DIN EN 15250-2007 Slow heat release appliances fired by solid fuel - Requirements and test methods English version of DIN EN 15250 2007-06《固体燃料点燃的慢放热器具 要求和试验方法》.pdf

1、June 2007DEUTSCHE NORM English price group 20No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 97.100.30!,y$U“9860150www

2、.din.deDDIN EN 15250Slow heat release appliances fired by solid fuel Requirements and test methodsEnglish version of DIN EN 15250:2007-06Speicherfeuersttten fr feste Brennstoffe Anforderungen und PrfverfahrenEnglische Fassung DIN EN 15250:2007-06SupersedesDIN 18840:2005-08See start of validitywww.be

3、uth.deDocument comprises 65 pages 09.07DIN EN 15250:2007-06 2 Start of validity This standard is intended to be valid from 01 June 2008. It should be noted that, in Germany, CE conformity marking of construction products conforming to this standard will be permitted once the standard has been listed

4、 in the Bundesanzeiger (German Federal Law Gazette). National foreword This standard includes safety requirements. This standard has been prepared by CEN/TC 295 “Residential solid fuel burning appliances” (Secretariat: BSI, United Kingdom). The responsible German body involved in its preparation was

5、 the Normenausschuss Heiz-, Koch- und Wrmgert (Heating and Cooking Equipment Standards Committee). This standard specifies requirements together with associated test methods for type testing slow heat release appliances fired by solid fuel. Amendments This standard differs from DIN 18840:2005-08 as

6、follows: a) The safety test has been modified. Previous editions DIN 18840: 2005-08 EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15250March 2007ICS 97.100.30English VersionSlow heat release appliances fired by solid fuel - Requirementsand test methodsAppareils de chauffage domestique combustibl

7、e solide libration lente de chaleur - Exigences et mthodes dessaiSpeicherfeuersttten fr feste Brennstoffe - Anforderungenund PrfverfahrenThis European Standard was approved by CEN on 13 January 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditi

8、ons for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three off

9、icial versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria,

10、Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FO

11、R STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15250:2007: EEN 15250:2007 (E) 2 Contents Page F

12、oreword .4 1 Scope 5 2 Normative references5 3 Terms and definitions .6 4 Materials, design and construction .9 4.1 Production documentation.9 4.2 Construction 10 4.2.1 General construction.10 4.2.2 Cleaning of heating surfaces .10 4.2.3 Flue spigot or socket.10 4.2.4 Flueways.10 4.2.5 Ashpan and as

13、h removal 11 4.2.6 Bottomgrate .11 4.2.7 Combustion air supply11 4.2.8 Control of flue gas.11 4.2.9 Firedoors and charging doors .12 4.2.10 Flue bypass device12 4.2.11 Front firebars and/or deepening plate.12 5 Safety 12 5.1 Temperature rise in the fuel storage container 12 5.2 Temperature rise of t

14、he operating components.12 5.3 Temperature of adjacent combustible materials12 5.4 Electrical safety .13 6 Performance.13 6.1 Flue gas temperature 13 6.2 Carbon monoxide emission .13 6.3 Efficiency13 6.4 Flue draught .13 6.5 Refuelling intervals13 6.6 Thermal storage capacity .13 7 Appliance instruc

15、tions14 7.1 General .14 7.2 Installation instructions 14 7.3 User operating instructions15 8 Marking .16 9 Evaluation of conformity 16 9.1 General .16 9.2 Type testing17 9.2.1 Initial type testing 17 9.2.2 Further type testing.18 9.3 Factory production control (FPC)20 9.3.1 General .20 9.3.2 Raw mat

16、erials and components.20 9.3.3 Control of inspection, measuring and test equipment20 9.3.4 Process control20 9.3.5 Product inspection, testing and evaluation21 9.3.6 Non conforming products 22 9.3.7 Corrective and preventive action.22 9.3.8 Handling, storage, packaging, preservation and delivery.22

17、EN 15250:2007 (E) 3 Annex A (normative) Test methods.23 A.1 Test environment.23 A.1.1 Ambient room temperature.23 A.1.2 Cross-draught 23 A.1.3 External sources23 A.2 Test assembly 23 A.2.1 General23 A.2.2 Trihedron 24 A.2.3 Measurement section 24 A.2.4 Connection of appliance to measurement section

18、25 A.2.5 Measurement of appliance surface temperature for slow heat release appliances .25 A.3 Measurement equipment 26 A.4 Test procedures.27 A.4.1 Appliance installation27 A.4.2 Fuel load .27 A.4.3 Fuelling and de-ashing the fire.28 A.4.4 Flue gas losses 28 A.4.5 Combustible heat losses in the res

19、idue28 A.4.6 Burning rate performance test .28 A.4.7 Temperature safety test for woodburning and multifuel appliances .29 A.5 Test results.30 A.6 Calculation methods .31 A.6.1 Notations and units used31 A.6.2 Equations32 A.7 Test report 36 Annex B (normative) Test fuels and recommended fuels 47 B.1

20、General47 B.2 Test fuel 47 B.2.1 Selection of test fuel47 B.2.2 Storage, preparation and analysis.47 B.3 Tests for recommended fuels 48 B.3.1 Basis of testing 48 B.3.2 Test methods and criteria.48 Annex C (informative) Calculation of an approximate heat release curve against time54 Annex ZA (informa

21、tive) Clauses of this European standard addressing the provisions of the EU Construction Products Directive .57 ZA.1 Scope and relevant characteristics .57 ZA.2 Procedure for the attestation of conformity of slow heat release appliances fired by solid fuels.59 ZA.2.1 System of attestation of conform

22、ity 59 ZA.2.2 EC Declaration of conformity .60 ZA.3 CE Marking and labelling60 Bibliography63 EN 15250:2007 (E) 4 Foreword This document (EN 15250:2007) has been prepared by Technical Committee CEN/TC 295 “Residential solid fuel burning appliances”, the secretariat of which is held by BSI. This Euro

23、pean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2007, and conflicting national standards shall be withdrawn at the latest by September 2007. This document has been prepared under a mandate given

24、to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the natio

25、nal standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, P

26、oland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 15250:2007 (E) 5 1 Scope This European Standard specifies requirements relating to the design, manufacture, construction, safety and performance (efficiency and emission) instructions and marking together

27、 with associated test methods and test fuels for type testing residential slow heat release appliances fired by solid fuel. This European Standard is applicable to hand fuelled intermittent burning slow heat release appliances having thermal storage capacity such that they can provide heat for a dec

28、lared period of time after the fire has gone out. This European Standard also specifies a minimum time period from the appliance achieving the maximum differential surface temperature and falling to 50 % of that maximum value. These appliances provide heat into the space where they are installed. Th

29、ese slow heat release appliances may be supplied either as an assembled appliance or as a manufacturers pre-designed unit consisting of pre-fabricated components designed to be built on site in accordance with the manufacturers specified assembly instructions. One off installations are not included.

30、 These appliances may burn either solid mineral fuels, peat briquettes, natural or manufactured wood logs or be multi-fuel in accordance with the appliance manufacturers instructions. Wood pellets which are hand fuelled may also be burned either on the existing appliance bottomgrate or in a special

31、basket arrangement which is placed by the user into the existing firebox. This European Standard is not applicable to mechanically fed appliances, appliances having fan assisted combustion air or appliances with boiler. 2 Normative references The following referenced documents are indispensable for

32、the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 50165:1997, Electrical equipment for non-electric appliances for household and similar purposes Safety

33、requirements ISO 334:1992, Solid mineral fuels Determination of total sulfur Eschka method ISO 351:1996, Solid mineral fuels Determination of total sulfur High temperature combustion method ISO 501:2003, Hard coal Determination of the crucible swelling number ISO 562:1998, Hard coal and coke Determi

34、nation of volatile matter ISO 609:1996, Solid mineral fuels Determination of carbon and hydrogen High temperature combustion method ISO 687:2004, Solid mineral fuels Coke Determination of moisture in the general analysis test sample ISO 1171:1997, Solid mineral fuels Determination of ash ISO 1928:19

35、95, Solid mineral fuels Determination of gross calorific value by the bomb calorimetric method, and calculation of net calorific value ISO 2859 (all parts), Sampling procedures for inspection by attributes ISO 11722:1999, Hard coal Determination of moisture in the general analysis test sample by dry

36、ing in nitrogen EN 15250:2007 (E) 6 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 air grilles components in the inlet and outlet openings to distribute and direct convection air flow 3.2 air inlet control manual or automatic device which co

37、ntrols the quantity of air supplied for combustion 3.3 appliance family group of appliances of similar construction and/or performance characteristics where it is permissible to test only selected appliances in accordance with the requirements of this standard 3.4 ash content of the fuel solid matte

38、r remaining after the complete combustion of solid fuel 3.5 ashpan removable receptacle shaped to receive the residue falling from the firebed 3.6 ashpit enclosed chamber designed to receive the residue or the ashpan 3.7 ashpit loss part of the residue which is combustible 3.8 basic firebed quantity

39、 of glowing embers which ensures ignition of the test fuel to be charged NOTE The basic firebed may be specified by the manufacturer. 3.9 batch charge proportion of the test load as declared by the manufacturer that can be added at specified intervals during the test period of the burning rate perfo

40、rmance test 3.10 bottomgrate part of the appliance at the base of the firebox which supports the firebed through which the residue falls into the ashpan or ashpit and through which combustion air and/or combustion gases may be drawn 3.11 bottomgrate bars; firebars bars supporting the fuelbed, separa

41、te or integral with a surrounding frame 3.12 charging door door which covers the refuelling opening 3.13 combustion air air supplied to the firebox which is entirely or partially used to burn the fuel EN 15250:2007 (E) 7 3.14 combustion gases compounds in gaseous form produced inside an appliance wh

42、en fuel is burned 3.15 de-ashing process of clearing a fuelbed and discharging the residue into the collecting receptacle 3.16 de-ashing mechanism device to agitate or disturb the ash to facilitate its removal from the firebed NOTE It may also be used to change the bottomgrate operating position on

43、some appliances. 3.17 draught regulator inlet device for admission of air downstream of the firebed, enabling the flue draught to be controlled 3.18 efficiency ratio of total heat output to the total heat input during the burning period expressed as a percentage 3.19 firebox; combustion chamber part

44、 of the appliance in which the fuel is burned 3.20 firebox opening aperture in the firebox through which an appliance may be fuelled 3.21 firedoor door through which the fire may be viewed and which may be opened to allow refuelling of the firebed 3.22 flue by-pass device device which in the open po

45、sition allows flue gases to pass directly to the flue spigot/socket NOTE This can be used as a preheating aid to overcome chimney condensation. 3.23 flue damper mechanism to change the flow of the combustion gases 3.24 flue draught differential between the static pressure in the place of installatio

46、n and the static pressure at the flue gas measurement point 3.25 flue gases gaseous compounds leaving the appliance flue spigot or socket and entering the flue gas connector 3.26 flue gas connector duct through which flue gases are conveyed from the flue spigot of the appliance into the chimney flue

47、 3.27 flue gas mass flow mass of flue gas drawn off from the appliance per unit of time EN 15250:2007 (E) 8 3.28 flue gas temperature temperature of the flue gas at the specified point in the measurement section 3.29 flue spigot; flue socket integral part of the appliance for connecting the flue gas

48、 connector thus permitting the deliberate escape of products of combustion into the chimney flue 3.30 flueway part of an appliance designed to convey combustion gases from the firebox to the flue spigot/socket 3.31 front firebars grating or plate fitted at the front of the firebox opening to prevent

49、 spillage of fuel and ash or to change the firebox capacity, or both 3.32 integral fuel storage container enclosed area forming part of the appliance, but not connected directly to the fuel charging area, in which fuel is stored prior to it being physically transferred by the user to the fuel charging 3.33 total heat input positionquantity of energy which the fuel provides to the appliance during 3.34 operating tool device supplied with the appliance for handling movable and/or hot components 3.35 primary air combustion air which passes