DIN EN 15337-2007 Adhesives - Determination of shear strength of anaerobic adhesives using pin-and-collar specimens (ISO 10123 1990 modified) English version of DIN EN 15337 2007-1.pdf

1、November 2007DEUTSCHE NORM English price group 8No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 83.180!$JI“1393825www.

2、din.deDDIN EN 15337Adhesives Determination of shear strength of anaerobic adhesives usingEnglish version of DIN EN 15337:2007-11Klebstoffe Bestimmung der Scherfestigkeit von anaeroben Klebstoffen unter Verwendung vonEnglische Fassung DIN EN 15337:2007-11SupersedesDIN 54452:1981-11www.beuth.deDocumen

3、t comprises 13 pagespin-and-collar specimens (ISO 10123:1990 modified)Bolzen-Hlse-Probekrpern (ISO 10123:1990 modifiziert)DIN EN 15337:2007-11 2 National foreword This standard has been prepared by Technical Committee CEN/TC 193 “Adhesives” (Secretariat: AENOR, Spain). The responsible German body in

4、volved in its preparation was the Normenausschuss Materialprfung (Materials Testing Standards Committee), Technical Committee NA 062-04-55 AA Prfung von Konstruk-tionsklebstoffen, -klebverbindungen und Kernverbunden. The incorporated changes as compared with ISO 10123:1990 are marked by vertical lin

5、es in the left margin. Amendments This standard differs from DIN 54452:1981-11 as follows: a) The title has been modified. b) The designation has been deleted. c) The preparation of test specimens has been modified and described in more detail. d) The loading rate has been modified. e) The pin lengt

6、h has been modified. f) The standard has been editorially revised. Previous editions DIN 54452: 1981-11 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15337 September 2007 ICS 83.180 English Version Adhesives - Determination of shear strength of anaerobic adhesives using pin-and-collar specime

7、ns (ISO 10123:1990 modified) Adhsifs - Dtermination de la rsistance au cisaillement des adhsifs anarobies sur assemblage de type axe-bague (ISO 10123:1990 modifie) Klebstoffe - Bestimmung der Scherfestigkeit von anaeroben Klebstoffen unter Verwendung von Bolzen-Hlse-Probekrpern (ISO 10123:1990 modif

8、iziert) This European Standard was approved by CEN on 28 July 2007. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographica

9、l references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN

10、member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Ital

11、y, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-10

12、50 Brussels 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15337:2007: EEN 15337:2007 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Principle4 4 Apparatus .4 5 Preparation of test specimens .4 6 Procedure

13、 .5 7 Precision.6 8 Test report 6 Annex A (informative) Example of adoption for tensile testing machine10 Bibliography 11 EN 15337:2007 (E) 3 Foreword This document (EN 15337:2007) has been prepared by Technical Committee CEN/TC 193 “Adhesives”, the secretariat of which is held by AENOR. This Europe

14、an Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2008, and conflicting national standards shall be withdrawn at the latest by March 2008. Attention is drawn to the possibility that some of the elements

15、of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Europea

16、n Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Ki

17、ngdom. Safety statement Persons using this document should be familiar with the principles of normal laboratory practices. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and h

18、ealth practices and ensure compliance with any regulatory conditions. EN 15337:2007 (E) 4 1 Scope This European Standard specifies a method for the determination of the shear strength of anaerobic-curing liquid adhesives used for retaining cylindrical assemblies pin-and-collar type, or for locking a

19、nd sealing threaded fasteners. This test method may also be used for other adhesives. The test is for ranking and quality control of adhesives. The result does not necessarily reflect the performance of the materials in service and the test is not suitable for providing numerical data for design pur

20、poses. NOTE Numerical design data may be obtained from tests using the materials and configurations used in the actual structure. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. Fo

21、r undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 7500-1, Metallic materials Verification of static uniaxial testing machines Part 1: Tension/compression testing machines Verification and calibration of the force-measuring system (ISO 7500

22、1:2004) 3 Principle The force required to shear the adhesive joint formed between a metal pin and a metal collar is determined. The static shear strength is calculated from this force. 4 Apparatus 4.1 Universal testing machine, complying with EN ISO 7500-1, class 1. The machine shall be able to appl

23、y a compressive force directly or indirectly. An example of a jig for compression testing for use on a pure tensile testing machine is shown in Annex A. 4.2 Test specimen support, made of hardened steel, as shown in Figure 1, for positioning the test specimen on the universal testing machine. 4.3 No

24、n-adhering material sheet (e.g. polyethylene sheet). 5 Preparation of test specimens 5.1 General Assemble no less than five specimens for each test as described below. 5.2 Each specimen shall be comprised of a pin of diameter (20 ) mm and a slip collar (20 ) mm in inside diameter and 18 mm 0,05 mm i

25、n width, both components being finished to 0,8 m to 1,6 m (see Figure 2). The material used for the collar and pin shall be stated in the test report. EN 15337:2007 (E) 5 NOTE Unless there is a specific requirement to test the adhesive with a specific material, low-grade carbon-steel (complying with

26、 grade 2 of ISO 683-9) is generally used and has been found to be satisfactory. The cutting oil used in the manufacture of specimens and any corrosion protection agent shall be completely soluble in the solvents used for degreasing at room temperature and shall contain no lanolin. 5.3 Clean all pins

27、 and collars with suitable cleaning agents to degrease them and allow them to dry. The cleaning agents used shall not leave any visually detectable residue on the surface. Allow the pins and collars to attain (23 2) C for at least 30 min before proceeding further with assembling, or store them in a

28、desiccator at (23 2) C. When stored use degreased specimens within four days or discard (oxidation affects the test results after this period of time). In any case, take precautions to avoid contamination in subsequent handling. Do not prime or activate unless specified for the material to be tested

29、 (if the specimen is primed or activated, state this in the test report). 5.4 Pre-assemble pins and collars before application of the adhesive, to ensure a smooth and sliding fit. Disassemble the parts. Apply sufficient adhesive to the surface of each pin, beginning at one end, to completely cover a

30、 length corresponding to the width of the collar in its final position. Also apply sufficient adhesive to completely cover the interior of the collar. Slip the collar over the pin completely, with a helicoidal back-and-forth movement (this operation shall not take longer than 6 s). 5.5 Place the ass

31、embly vertically with the fillet upwards on a non-adhering material (e.g. polyethylene sheet) (Figure 3). Take care that the assembly is at the required temperature, and do not place on a hot or cold surface. 5.6 Before application of the adhesive, an activator may be applied as recommended by the m

32、anufacturer. 5.7 Cure the adhesive in accordance with the manufacturers instructions. At the end of the curing period, remove by wiping excess of uncured material from the surfaces of the pin-and-collar assemblies. 6 Procedure After allowing for cure and any predetermined environmental conditioning,

33、 determine the static shear strength as follows: Place the pin-and-collar assembly in the steel specimen support and place the support on the test device (see Figure 4). Load the specimen smoothly using a constant crosshead speed between 1 mm/min and 2 mm/min. Record the maximum load in Newtons. Cal

34、culate the static shear strength , expressed in Megapascals, using the equation: = F/A (1) where F is the maximum load, in Newtons; A is the bond area, in square millimetres. Test no fewer than five specimens. The bond area shall be calculated from the dimensions of the pin-and collar assembly given

35、 in Figure 3, while the effective bond length derives to 16 mm from the nominal collar width by subtracting the length of both chamfers. EN 15337:2007 (E) 6 7 Precision The precision of this test method is not known because inter-laboratory data are not available. 8 Test report The test report shall

36、 include the following information: a) reference to this European Standard (EN 15337:2007); b) complete identification of the adhesive tested, including type, form, source, date manufactured and manufacturers code number; c) complete identification of the material used and the method of cleaning and

37、 surface preparation prior to bonding; d) adhesive-application and bonding conditions used in preparing the specimens; e) conditioning procedure used for the specimens prior to testing; f) number of specimens tested; g) crosshead speed; h) average value of the maximum load and the standard deviation

38、, as well as the average value and the standard deviation of the shear strength. EN 15337:2007 (E) 7 Dimensions in millimetres Key a Chamfers 0,5 x 45 Figure 1 Test specimen support EN 15337:2007 (E) 8 Dimensions in millimetres (except where otherwise stated) A) Pin B) Collar Key a Break edge Figure

39、 2 Pin-and-collar assembly EN 15337:2007 (E) 9 Key 1 Pin 2 Collar 3 Non-adhering sheet (e.g. polyethylene sheet) Figure 3 Test specimens positioned for curing Key 1 Specimen support 2 Specimen 3 Upper compression plate 4 Lower compression plate 5 Axis of cell for measurement of breaking strain Figur

40、e 4 Test device EN 15337:2007 (E) 10 Annex A (informative) Example of adoption for tensile testing machine Key a Applied force Figure A.1 Jig for compression testing on tensile testing machines EN 15337:2007 (E) 11 Bibliography 1 ISO 683-9, Heat-treatable steels, alloy steels and free-cutting steels Part 9: Wrought free-cutting steels