1、December 2009DEUTSCHE NORM English price group 10No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 13.220.40; 13.310!$ZJ
2、“1559639www.din.deDDIN EN 15659Secure storage units Classification and methods of test for resistance to fire Light fire storage unitsEnglish version of DIN EN 15659:2009-12Wertbehltnisse Klassifizierung und Methoden zur Prfung des Widerstandes gegen Brand Leichte BrandschutzschrnkeEnglische Fassung
3、 DIN EN 15659:2009-12www.beuth.deDocument comprises pages15DIN EN 15659:2009-12 Start of validity This standard takes effect on 1 December 2009. National foreword This standard has been prepared by Technical Committee CEN/TC 263 “Secure storage of cash, valuables and data media” (Secretariat: BSI, U
4、nited Kingdom). The responsible German body involved in its preparation was the Normenausschuss Maschinenbau (Mechanical Engineering Standards Committee), Technical Committee NA 060-20-01 AA Geldschrnke und Tresoranlagen. The European Standard referred to in Clause 2 has been published as the corres
5、ponding DIN EN Standard with the same number. 2 EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15659April 2009ICS 13.220.40; 91.060.01English VersionSecure storage units - Classification and methods of test forresistance to fire - Light fire storage unitsUnits de stockage en lieu sr - Classificat
6、ion et mthodesdessais de rsistance au feu - Meubles ignifuges premierniveauWertbehltnisse - Klassifizierung und Methoden zurPrfung des Widerstandes gegen Brand - LeichteBrandschutzschrnkeThis European Standard was approved by CEN on 19 March 2009.CEN members are bound to comply with the CEN/CENELEC
7、Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN m
8、ember.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN member
9、s are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Swit
10、zerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15
11、659:2009: EEN 15659:2009 (E) 2 Contents Page Foreword . 3 Introduction 4 1 Scope . 5 2 Normative references . 5 3 Terms and definitions 5 4 Requirements, classification and locks . 5 5 Test specimen, technical documentation and correlation . 6 5.1 Test specimen . 6 5.2 Technical documentation of the
12、 test specimen 6 5.3 Correlation of test specimens and technical documentation 7 6 Test methods . 7 6.1 Principle . 7 6.2 Test equipment . 7 6.3 Preparation for test . 8 6.4 Procedure 10 6.4.1 Correlation . 10 6.4.2 Fire endurance test . 11 6.4.3 Examination . 12 7 Test report . 12 8 Marking 12 Figu
13、res Figure 1 Measurement points . 9 Figure 2 Cable entry hole and sealing . 10 Figure 3 Protection of instrument cables 11 Tables Table 1 Protection level requirements . 6 DIN EN 15659:2009-12 EN 15659:2009 (E) 3 Foreword This document (EN 15659:2009) has been prepared by Technical Committee CEN/TC
14、263 “Secure storage of cash, valuables and data media”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards sh
15、all be withdrawn at the latest by October 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal
16、Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
17、Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 15659:2009-12 EN 15659:2009 (E) 4 Introduction The testing conditions given in this European Standard provide a basis for simulating fires to determine, in a reproducible way
18、, the fire resistance of light fire storage units at various protection levels. The protection levels enable a comparison to be made of the resistance against fire provided by different constructions. The threshold value for the maximum temperature increase of 150 K at every measuring point in the p
19、rotection levels LFS 30 P and LFS 60 P for light fire storage units from a starting temperature of (21 1)C, as defined in this European Standard, refers to the relatively short-term stress due to high temperatures during a fire test. It is not normally experienced by paper media stored in light fire
20、 storage units in the normal and correct way. DIN EN 15659:2009-12 EN 15659:2009 (E) 5 1 Scope This European Standard specifies requirements for light fire storage units providing protection against fire. The method of test is specified to determine the ability of light fire storage units to protect
21、 paper media from the effects of fire. Two levels of fire exposure periods (LFS 30 P and LFS 60 P) are specified using the maximum temperature increase permitted within the storage space of the light fire storage unit. Requirements are also specified for the test specimen, the technical documentatio
22、n for the test specimen, correlation of the test specimen with the technical documentation, preparation for type testing and test procedures. A scheme to classify the light fire storage units from the test results is also given (see Table 1). 2 Normative references The following referenced documents
23、 are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1363-1:1999, Fire resistance tests Part 1: General requirements EN 60584-1, Ther
24、mocouples Part 1: Reference tables (IEC 60584-1:1995). 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 light fire storage unit storage unit designed to protect paper media, except for paper grades where data loss occurs at temperatures below
25、172C, as well as valuables against the effects of temperatures up to 172C NOTE A light fire storage unit can have doors, drawers, lids, connections and fittings. 3.2 compartment part of a light fire storage unit which can be closed with a separate door, lid or cover NOTE A compartment formed by inse
26、rting a shelf board is not a compartment within the meaning of this standard. 3.3 lock device which verifies an entered code and performs a blocking function on the boltwork or the door 4 Requirements, classification and locks 4.1 Light fire storage units shall provide protection against the effects
27、 of fire (see Clause 6) and be classified as specified in Table 1. DIN EN 15659:2009-12 EN 15659:2009 (E) 6 Table 1 Protection level requirements Protection level Maximum temperature increase 30 min 60 min LFS 30 P LFS 60 P 150 K NOTE 1 Where LFS is the symbol applied for light fire storage units. N
28、OTE 2 The numerical values in the protection level are the duration of fire exposure during the type test in minutes. NOTE 3 P represents protection of data on paper, excluding those paper grades which lose data below 172C. 4.2 Light fire storage units shall be fitted with a lock. 5 Test specimen, t
29、echnical documentation and correlation 5.1 Test specimen Of several models of a series (with one door, two doors, drawers, etc.) having the same design, protection and construction features (type and thickness of construction and protective materials, rabbet geometry, etc.) as well as the same base
30、(with a tolerance of 15 % each applicable to the internal dimensions of width and depth), the models with the smallest and largest internal height resp. the lowest and highest number of drawers shall be tested. Light fire storage units with double doors shall be regarded as a separate model range. W
31、here a variety of locking options is available, the test specimen used in the type test shall be coordinated with the testing laboratory. Two identical light fire storage units shall be available: one for the fire endurance test, the other for verifying correlation of the filling material with the t
32、echnical documentation. The testing laboratory shall decide which test specimen will be used for the type test. The test specimen shall be modified at its base for installing the measuring instrumentation (see 6.3.1 and Figure 2) and may have, but need not have a plinth. 5.2 Technical documentation
33、of the test specimen Detailed technical documentation about the range and test specimen (drawings, specifications of materials, installation and processing advice) shall be submitted to the testing laboratory before the type test. The drawings shall give specifications as to height, width and depth
34、of the test specimens, materials and their thicknesses, dimensions of rabbet edges, locking system, welds including the method of their execution, seals, etc. The mass of the plinth shall be given. Samples and detailed specifications of all heat protection materials and seals used in the test specim
35、ens shall accompany the test specimens. The date(s) on which the test specimens were filled with fire protection materials shall be given. NOTE 1 With reference to all heat protection materials, the technical documentation should include: a) quality control parameters, and b) details of the performa
36、nce characteristics, or c) details of the constituent materials and processing methods. DIN EN 15659:2009-12 EN 15659:2009 (E) 7 NOTE 2 In connection with the type test, the testing laboratory should mark three sets of the technical documentation with signature, stamp and date. One set is sent to th
37、e applicant. One set is added to the monitoring documentation for certification and quality assurance. One set is kept in the testing files of the test laboratory. 5.3 Correlation of test specimens and technical documentation The test specimens and the supplied technical documentation must correlate
38、. As to mass, the two test specimens shall not differ by more than 10 %. In series production, the wall, ceiling and door thicknesses must not be below the specified minimum limit of the type-tested thickness by more than 3 %. 6 Test methods 6.1 Principle The fire endurance of the test specimen is a
39、ssessed by heating in a furnace. During the type test the temperature in the interior of the test specimen is measured. 6.2 Test equipment 6.2.1 The furnace which must be capable of providing the uniform heating conditions specified in this standard, and constructed so that the four vertical walls o
40、f the test specimen can each be exposed to the same heating conditions with no direct flame impingement onto the test specimen. The distance between the interior walls of the furnace and the surface of the test specimen shall be 750 mm. The furnace conditions shall conform to EN 1363-1. To meet thes
41、e conditions, the setting of the neutral pressure level shall be made in accordance with 6.2.2 and the measurement of the temperature in the interior of the furnace shall be made with instrumentation in accordance with 6.2.3. 6.2.2 The furnace shall be operated such that the neutral pressure level i
42、s reached after 5 min of firing, measured at 5 Pa 1,000 mm above the furnace base. Test specimens with an external height of 1,000 mm shall be placed on the furnace base during the type test. Test specimens with an external height of 1,000 mm shall be positioned on a plinth of brick with a height of
43、 500 mm. For pressure measurements, pressure measuring heads in accordance with 4.5.2 of EN 1363-1:1999 shall be used. NOTE In order to ensure consistent heating conditions, the width of the plinth area around the projected cross-sectional area of the test specimen should not exceed 200 mm. 6.2.3 Th
44、ermocouples of type K (NiCr-Ni) with a measurement uncertainty in accordance with EN 60584-1 for measuring the furnace temperature. The furnace thermocouples shall be plate thermometers according to 4.5.1.1 of EN 1363-1:1999. 6.2.4 Thermocouples consisting of 0.5 mm diameter wires of type K (NiCr-Ni
45、) or type J (Fe-CuNi) with a measurement uncertainty in accordance with EN 60584-1 for measuring the air and surface temperatures in the test specimen. The measurement results shall be recorded at intervals not greater than 1 min. The contact measurement points shall be assembled in accordance with
46、4.5.1.2 and 4.5.1.4 of EN 1363-1:1999, respectively. 6.2.5 Timing device, capable of running continuously throughout the test period. 6.2.6 Equipment for weighing test specimens, with an error limit of 3 %. DIN EN 15659:2009-12 EN 15659:2009 (E) 8 6.3 Preparation for test 6.3.1 Suitably modify the b
47、ase (see 6.3.3) of the test specimen for the fire endurance test (see 6.4.2) to allow the entry of thermocouple cables. Plinths and other elements that may prevent proper protection of the thermocouple cables may be removed. 6.3.2 For the fire endurance test (see 6.4.2) install thermocouples (see 6.
48、2.4) at the following measuring points in the test specimen to enable temperature measurement: a) Four thermocouples for measuring the air temperature in the upper corners each (26.5 1.5) mm from the walls, interior door surface and ceiling (see measuring points 1, 2, 3 and 4 of Figure 1). b) One th
49、ermocouple for measuring the surface temperature on each of the ceiling, side walls, rear wall, and door, approximately in the centre of each surface (see measuring points 5, 6, 7, 8 and 9 of Figure 1). c) For two-door cabinets only, two additional thermocouples for measuring the air temperature at (26.5 1.5) mm from the centre door joint, one (26.5 1.5) mm from the ceiling and the other approximately half-way up the cabinet (see measuring points 10 and 11 of Figure 1). d) For test specimens with several compartments (e.g. dr
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1