DIN EN 15719-2016 Sanitary appliances - Baths made from impact modified coextruded ABS acrylic sheets - Requirements and test methods German version EN 15719 2015《卫生用具 冲击改良型共挤ABS 丙.pdf

1、February 2016 English price group 14No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91.140.70!%LSJ“2414839www.din.d

2、eDIN EN 15719Sanitary appliances Baths made from impact modified coextruded ABS/acrylic sheets Requirements and test methods;English version EN 15719:2015,English translation of DIN EN 15719:2016-02Sanitrausstattungsgegenstnde Badewannen, hergestellt aus schlagzh-modifizierten coextrudierten ABS/Acr

3、ylplatten Anforderungen und Prfverfahren;Englische Fassung EN 15719:2015,Englische bersetzung von DIN EN 15719:2016-02Appareils sanitaires Baignoires en feuilles coextrudes ABS/acrylique modifi choc Prescriptions et mthodes dessai;Version anglaise EN 15719:2015,Traduction anglaise de DIN EN 15719:20

4、16-02SupersedesDIN EN 15719:2010-04www.beuth.deDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.Document comprises 29 pages 03.16 DIN EN 15719:2016-02 2 A comma is used as the decimal marker. National foreword This document (EN 15719

5、:2015) has been prepared by Technical Committee CEN/TC 163 “Sanitary appliances” (Secretariat: UNI, Italy). The preliminary work was done by Working Group WG 4 “Baths (W/Pools), shower trays (performance testing) of CEN/TC 163. The responsible German body involved in its preparation was DIN-Normenau

6、sschuss Wasserwesen (DIN Standards Committee Water Practice), Working Committee NA 119-5-18-10 UA Bade- und Duscheinrich-tungen. Amendments This standard differs from DIN EN 15719:2010-04 as follows: a) the method for determining the resistance of surfaces to scratching has been modified; b) the sta

7、ndard has been editorially revised. Previous editions DIN EN 15719: 2010-04 ”EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15719 November 2015 ICS 91.140.70 Supersedes EN 15719:2009English Version Sanitary appliances - Baths made from impact modified coextruded ABS/acrylic sheets - Requiremen

8、ts and test methods Appareils sanitaires - Baignoires en feuilles coextrudes ABS/acrylique modifi choc - Prescriptions et mthodes dessai Sanitrausstattungsgegenstnde - Badewannen, hergestellt aus schlagzh-modifizierten coextrudierten ABS/Acrylplatten - Anforderungen und PrfverfahrenThis European Sta

9、ndard was approved by CEN on 20 September 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concern

10、ing such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into

11、its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Ger

12、many, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE F

13、R NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15719:2015 EEN 15719:2015 (E) 2 Contents Page European foreword . 4 1 Scope 5 2 Normative references 5

14、3 Terms and definitions . 5 4 Requirements . 5 4.1 General 5 4.2 Material . 5 4.3 Surface appearance 5 4.4 Waste outlet hole . 5 4.5 Overflow hole . 6 4.6 Hole edges 6 4.7 Bath-mounted tapware . 6 4.8 Handgrips . 6 4.9 Dimensional deviations 6 4.10 Geometric deviations . 6 4.10.1 General 6 4.10.2 Sq

15、uaring 6 4.10.3 Straightness of the rim sides . 6 4.10.4 Straightness of the bottom edge of the rim 6 4.10.5 Flatness of the top surface of the rim . 7 4.11 Bottom of the bath 7 4.12 Resistance to temperature changes . 7 4.13 Resistance to impact 7 4.14 Permitted deflections 7 4.15 Bath rims 7 4.16

16、Surface mechanical resistance . 8 4.17 Chemical and stain resistance 8 5 Marking . 8 Annex A (normative) Bath test methods 9 A.1 Sequence of tests . 9 A.2 Geometric deviations . 9 A.2.1 Test apparatus 9 A.2.2 Squaring 9 A.2.3 Straightness of the rim side 10 A.2.4 Straightness of the bottom edge of t

17、he rim . 11 A.2.5 Flatness of the top surface of the rim 12 A.3 Resistance to temperature change 13 A.3.1 Test apparatus. 13 A.3.2 Procedure 13 A.4 Resistance to impact . 14 DIN EN 15719:2016-02 EN 15719:2015 (E) 3 A.4.1 Test apparatus . 14 A.4.2 Test procedure 14 A.5 Determination of deflections 15

18、 A.5.1 General . 15 A.5.2 Test apparatus . 15 A.5.3 Installation methods . 16 A.5.4 Preloading . 18 A.5.5 Deflection test 1 Deflection of the rim and the bottom due to a load on the bottom 18 A.5.6 Deflection test 2 Deflection of the bottom and rim due to a load on the bottom . 20 A.5.7 Deflection t

19、est 3 Deflection of the rim due to a load on the long side of the rim 21 A.5.8 Deflection test 4 Deflection of the rim due to a load on the end of the bath 22 A.6 Handgrip tests 24 A.6.1 General . 24 A.6.2 Test apparatus . 24 A.6.3 Procedure 24 A.7 Resistance to scratching . 24 A.7.1 Test apparatus

20、. 24 A.7.2 Test specimen 25 A.7.3 Procedure 25 Bibliography . 27 DIN EN 15719:2016-02 EN 15719:2015 (E) 4 European foreword This document (EN 15719:2015) has been prepared by Technical Committee CEN/TC 163 “Sanitary appliances”, the secretariat of which is held by UNI. This European Standard shall b

21、e given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2016, and conflicting national standards shall be withdrawn at the latest by May 2016. Attention is drawn to the possibility that some of the elements of this document may be

22、 the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 15719:2009. The only change from the previous edition is in A.7.3 where “50 %” has been changed to “25 %”. According to the CEN/CENELEC Internal

23、Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Irelan

24、d, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 15719:2016-02 EN 15719:2015 (E) 5 1 Scope This European Standard specifies requirements for baths for domestic purpose

25、s made from impact modified coextruded ABS/acrylic sheets conforming to EN 13559 with the aim of ensuring that the product, when installed in accordance with the manufacturers instructions, will provide satisfactory performance in use. This European Standard is applicable to all sizes and shapes of

26、baths. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including an

27、y amendments) applies. EN 232, Baths Connecting dimensions EN 13559:2003, Specifications for impact modified coextruded ABS/Acrylic sheets for baths and shower trays for domestic purposes ISO 4586-2:2004, High-pressure decorative laminates Sheets made from thermosetting resins Part 2: Determination

28、of properties 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 domestic purposes use in homes, hotels, accommodation for students, hospitals and similar buildings, except when special medical provisions are required 4 Requirements 4.1 General

29、The manufacturer shall provide instructions for installation and care with each bath. The bath shall be free from sharp edges that would be exposed after the installation of the bath in accordance with the manufacturers instructions. 4.2 Material The bath shall be manufactured from impact modified c

30、oextruded ABS/acrylic sheet material complying with EN 13559. 4.3 Surface appearance When the bath is visually inspected under strong and oblique illumination there shall be no evidence of cracks, chips, or other surface defects, such as unexpected changes in colours, etc. that will impair the appea

31、rance or performance of the bath. 4.4 Waste outlet hole The bath shall have at least one outlet hole. The dimensions of the waste outlet hole and the clearance around the waste outlet hole shall either be in accordance with the requirements of EN 232 or the manufacturer shall supply or recommend a s

32、uitable waste outlet fitting. DIN EN 15719:2016-02 EN 15719:2015 (E) 6 4.5 Overflow hole When the bath is provided with an overflow hole the dimensions of the overflow hole and the clearance around the overflow hole shall either be in accordance with the requirements of EN 232 or the manufacturer sh

33、all supply or recommend a suitable overflow fitting. 4.6 Hole edges The edges of any holes in the bath shall not show evidence of chips, cracks, or any other defects that may impair the appearance or performance of the bath. 4.7 Bath-mounted tapware When the bath is intended to accommodate bath-moun

34、ted tapware the space and area provided shall either comply with the requirements of EN 232 or the manufacturer shall supply or recommend a suitable tapware. 4.8 Handgrips When a handgrip(s) is fitted it shall be tested in accordance with A.6 and the bath and the handgrip shall be free from any perm

35、anent deformation or other defects that will impair the functioning and/or the appearance of the bath. If not pre-fitted by the manufacturer, the manufacturers instructions shall indicate how and where the handgrips are fitted. 4.9 Dimensional deviations The dimensions of baths shall not deviate fro

36、m the size quoted by the manufacturer by greater than 5 mm. If the manufacturer states two sizes (e.g. both a work size and a nominal size) he shall state to which size the permitted deviations apply. For round baths, length and width correspond to the diameter. 4.10 Geometric deviations 4.10.1 Gene

37、ral The straight sides or edges of the bath that might abut independent surroundings or supporting structures shall comply with the requirements of 4.10.2 to 4.10.4 and all baths shall comply with 4.10.5. These requirements are not applicable to sides or edges that are purposely designed as curves o

38、r slopes. 4.10.2 Squaring When tested in accordance with A.2.2 the deviation from square, q, shall be less than or equal to 5 mm. 4.10.3 Straightness of the rim sides When tested in accordance with A.2.3 the deviation from straightness of the rim sides, s, shall be less than or equal to 5 mm. 4.10.4

39、 Straightness of the bottom edge of the rim When tested in accordance with A.2.4 the deviation from straightness of the bottom edge of the rim, r, shall be less than or equal to 5 mm. DIN EN 15719:2016-02 EN 15719:2015 (E) 7 4.10.5 Flatness of the top surface of the rim When tested in accordance wit

40、h A.2.5 the deviation from flatness of the top surface of the rim, c, shall be less than or equal to 5 mm. 4.11 Bottom of the bath When the bath is installed in accordance with the manufacturers instructions and the waste outlet hole is open, all water shall empty from the bath unless prevented by s

41、urface tension. 4.12 Resistance to temperature changes When tested in accordance with A.3 baths shall show no evidence of distortion or other defects that impair the appearance or functioning of the bath and any deflection shall be less than or equal to 4 mm. 4.13 Resistance to impact When tested in

42、 accordance with A.4 the bottom and the rim of the bath shall show no evidence of distortion or other defects that impair the appearance or functioning of the bath. 4.14 Permitted deflections When tested in accordance with A.5 the deflections shall be less than or equal to the values given in Table

43、1. Table 1 Permitted deflections Test method Maximum deflections aunder load and permitted residual deflections for installation methods bmm a) b) c) d) e) A.5.5 1 on the four free rims 2 on the bottom 1 on the three free rims 0,5 on the fixed rim 2 on the bottom 1 on the two free rims 0,5 on the tw

44、o fixed rims 2 on the bottom 1 on the free rim 0,5 on the three fixed rims 2 on the bottom 0,5 on all rims 2 on the bottom A.5.6 2 on the four free rims 3 on the bottom 2 on the three free rims 0,5 on the fixed rim 3 on the bottom 2 on the two free rims 0,5 on the two fixed rims 3 on the bottom 2 on

45、 the free rim 0,5 on the three fixed rims 3 on the bottom 0,5 on all rims 3 on the bottom A.5.7 4 on the rim 0,3 residual 4 on the rim 0,3 residual 4 on the rim 0,3 residual 4 on the rim 0,3 residual Not applicable A.5.8 4 on the rim 0,3 residual 4 on the rim 0,3 residual 4 on the rim 0,3 residual N

46、ot applicable Not applicable aValues in addition to any deflection of the test rig (see A.5.2). bSee A.5.3. 4.15 Bath rims When a bath incorporating a nominally flat top surface of the rim is installed in accordance with the manufacturers instructions, the rim shall not encourage water to drain away

47、 from the inside of the DIN EN 15719:2016-02 EN 15719:2015 (E) 8 bath. Roll top rims and rims incorporating special features, e.g. headrests, are not subject to this requirement. 4.16 Surface mechanical resistance When tested in accordance with A.7, any scratch shall not exceeded 0,1 mm or the total

48、 thickness of the top layer whichever is the least. 4.17 Chemical and stain resistance When tested in accordance with EN 13559:2003, 5.4, baths shall show no permanent staining or deterioration. 5 Marking Baths shall be legibly marked with the following information: a) reference to this European Sta

49、ndard (EN 15719); b) the name or trademark of the manufacturer or supplier. DIN EN 15719:2016-02 EN 15719:2015 (E) 9 Annex A (normative) Bath test methods A.1 Sequence of tests The tests shall be carried out on one bath of each type in the sequence A.2, A.3, A.5, A.4, A.6, A.7. A.2 Geometric deviations A.2.1 Test apparatus a) length measuring device with an accuracy of 0,5 mm;