1、May 2013 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91.
2、100.60!%$;T“2012449www.din.deDDIN EN 1607Thermal insulating products for building applications Determination of tensile strength perpendicular to faces;English version EN 1607:2013,English translation of DIN EN 1607:2013-05Wrmedmmstoffe fr das Bauwesen Bestimmung der Zugfestigkeit senkrecht zur Plat
3、tenebene;Englische Fassung EN 1607:2013,Englische bersetzung von DIN EN 1607:2013-05Produits isolants thermiques destins aux applications du btiment Dtermination de la rsistance la traction perpendiculairement aux faces;Version anglaise EN 1607:2013,Traduction anglaise de DIN EN 1607:2013-05Supersed
4、esDIN EN 1607:1997-01www.beuth.deDocument comprises 12 pagesIn case of doubt, the German-language original shall be considered authoritative.04.13DIN EN 1607:2013-05 2 A comma is used as the decimal marker. National foreword This document (EN 1607:2013) has been prepared by Technical Committee CEN/T
5、C 88 “Thermal insulating materials and products” (Secretariat: DIN, Germany) The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Working Committee NA 005-56-60 AA Wrmedmmstoffe. The DIN Standards corresponding
6、 to the International Standards referred to in this document are as follows: ISO 5725-1 DIN ISO 5725-1 ISO 5725-2 DIN ISO 5725-2 Amendments This standard differs from DIN EN 1607:1997-01 as follows: a) the standard has been editorially revised. Previous editions DIN 1101: 1938-09, 1952x-01, 1960-10,
7、 1970-04, 1980-03, 1989-11 DIN 18165: 1957-08, 1963-03 DIN 1104-1: 1970-04, 1980-03 DIN 18165-1: 1975-01, 1987-03, 1991-07 DIN 52274: 1986-07 DIN EN 1607: 1997-01 National Annex NA (informative) Bibliography DIN ISO 5725-1, Accuracy (trueness and precision) of measurement methods and results Part 1:
8、 General principles and definitions DIN ISO 5725-2, Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1607 March 20
9、13 ICS 91.100.60 Supersedes EN 1607:1996English Version Thermal insulating products for building applications - Determination of tensile strength perpendicular to faces Produits isolants thermiques destins aux applications du btiment - Dtermination de la rsistance la traction perpendiculairement aux
10、 faces Wrmedmmstoffe fr das Bauwesen - Bestimmung der Zugfestigkeit senkrecht zur Plattenebene This European Standard was approved by CEN on 15 December 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard th
11、e status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, Fren
12、ch, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria,
13、 Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey
14、and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1607
15、:2013: EEN 1607:2013 (E) 2 Contents Page Foreword . 3 1 Scope 5 2 Normative references . 5 3 Terms and definitions 5 4 Principle 5 5 Apparatus . 5 6 Test specimens 6 7 Procedure . 8 8 Calculation and expression of results 9 9 Accuracy of measurement . 9 10 Test report 9 DIN EN 1607:2013-05 EN 1607:2
16、013 (E) 3 Foreword This document (EN 1607:2013) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text
17、 or by endorsement, at the latest by September 2013, and conflicting national standards shall be withdrawn at the latest by September 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held respo
18、nsible for identifying any or all such patent rights. This document supersedes EN 1607:1996. The revision of this standard contains no major changes, only minor corrections and clarifications of an editorial nature. This European Standard is one of a series of standards which specify test methods fo
19、r determining dimensions and properties of thermal insulating materials and products. It supports a series of product standards for thermal insulating materials and products which derive from the Council Directive of 21 December 1988 on the approximation of laws, regulations and administrative provi
20、sions of the Member States relating to construction products (Directive 89/106/EEC) through the consideration of the essential requirements. This European Standard has been drafted for applications in building, but it may also be used in other areas where it is relevant. This European test standard
21、is one of the following group of interrelated standards on test methods for determining dimensions and properties of thermal insulation materials and products, all of which fall within the scope of CEN/TC 88: EN 822, Thermal insulating products for building applications Determination of length and w
22、idth EN 823, Thermal insulating products for building applications Determination of thickness EN 824, Thermal insulating products for building applications Determination of squareness EN 825, Thermal insulating products for building applications Determination of flatness EN 826, Thermal insulating p
23、roducts for building applications Determination of compression behaviour EN 1602, Thermal insulating products for building applications Determination of the apparent density EN 1603, Thermal insulating products for building applications Determination of dimensional stability under constant normal la
24、boratory conditions (23 C/50 % relative humidity) EN 1604, Thermal insulating products for building applications Determination of dimensional stability under specified temperature and humidity conditions EN 1605, Thermal insulating products for building applications Determination of deformation unde
25、r specified compressive load and temperature conditions EN 1606, Thermal insulating products for building applications Determination of compressive creep DIN EN 1607:2013-05 EN 1607:2013 (E) 4 EN 1607, Thermal insulating products for building applications Determination of tensile strength perpendicu
26、lar to faces EN 1608, Thermal insulating products for building applications Determination of tensile strength parallel to faces EN 1609, Thermal insulating products for building applications Determination of short-term water absorption by partial immersion EN 12085, Thermal insulating products for b
27、uilding applications Determination of linear dimensions of test specimens EN 12086, Thermal insulating products for building applications Determination of water vapour transmission properties EN 12087, Thermal insulating products for building applications Determination of long-term water absorption
28、by immersion EN 12088, Thermal insulating products for building applications Determination of long-term water absorption by diffusion EN 12089, Thermal insulating products for building applications Determination of bending behaviour EN 12090, Thermal insulating products for building applications Det
29、ermination of shear behaviour EN 12091, Thermal insulating products for building applications Determination of freeze-thaw resistance EN 12429, Thermal insulating products for building applications Conditioning to moisture equilibrium under specified temperature and humidity conditions EN 12430, The
30、rmal insulating products for building applications Determination of behaviour under point load EN 12431, Thermal insulating products for building applications Determination of thickness for floating floor insulating products EN 13793, Thermal insulating products for building applications Determinati
31、on of behaviour under cyclic loading EN 13820, Thermal insulating materials for building applications Determination of organic content According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Aus
32、tria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swed
33、en, Switzerland, Turkey and the United Kingdom. DIN EN 1607:2013-05 EN 1607:2013 (E) 5 1 Scope This European Standard specifies the equipment and procedures for determining the tensile strength of a product perpendicular to its faces. It is applicable to thermal insulating products. 2 Normative refe
34、rences The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
35、EN 12085, Thermal insulating products for building applications Determination of linear dimensions of test specimens ISO 5725-1, Accuracy (trueness and precision) of measurement methods and results Part 1: General principles and definitions ISO 5725-2, Accuracy (trueness and precision) of measuremen
36、t methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method 3 Terms and definitions For the purposes of this document, the following term and definition applies. 3.1 tensile strength perpendicular to faces mtmaximum recorded
37、tensile force perpendicular to the product faces during the pulling operation, divided by the cross-sectional area of the test specimen 4 Principle A test specimen is attached between two rigid plates or blocks, fastened in a tensile testing machine and pulled apart at a given speed. The maximum ten
38、sile force is recorded and the tensile strength of the test specimen is calculated. 5 Apparatus 5.1 Tensile testing machine, appropriate for the range of force and displacement involved, capable of having a constant crosshead speed adjusted to (10 1) mm/min and capable of measuring the force to an a
39、ccuracy of 1 %. 5.2 Rigid plates or blocks, with self-aligning attachment to avoid uneven distribution of tensile stress during the test. Examples of suitable arrangement to bond the test specimen are shown in Figure 1. 5.3 Adhesive, used to bond the test specimen between the rigid plates or blocks:
40、 The adhesive shall not reinforce or damage the surface layers of the product. Hot adhesives shall be avoided if they damage the product. Any solvent used shall be compatible with the product. Any test equipment which provides the same result with at least the same accuracy may be used. DIN EN 1607:
41、2013-05 EN 1607:2013 (E) 6 6 Test specimens 6.1 Dimensions of test specimens The thickness of test specimens shall be equal to the original product thickness including any skins, facings and/or coatings. The test specimens shall be prisms of square cross section having sides of the following recomme
42、nded dimensions: 50 mm 50 mm or 100 mm 100 mm or 150 mm 150 mm or 200 mm 200 mm or 300 mm 300 mm. Dimensions used shall be as specified in the relevant product standard. In the absence of a product standard or any other European technical specification, the dimensions of test specimens may be agreed
43、 between parties. The linear dimensions shall be determined in accordance with EN 12085 to an accuracy of 0,5 %. DIN EN 1607:2013-05 EN 1607:2013 (E) 7 Figure 1 a) Key 1 bolt 2 connecting shaft 3 metal blocks 4 adhesive 5 test specimen Figure 1 b) Key 1 rigid plate 2 adhesive 3 test specimen Figure
44、1 Examples of suitable arrangement to bond the specimen DIN EN 1607:2013-05 EN 1607:2013 (E) 8 6.2 Number of test specimens The number of test specimens shall be as specified in the relevant product standard. If the number is not specified, then at least five test specimens shall be used. In the abs
45、ence of a product standard or any other European technical specification, the number of test specimens may be agreed between parties. 6.3 Preparation of test specimens The test specimens shall be cut from the product so that the test specimen base is normal to the direction of the tensile force appl
46、ied to the product in use. Test specimens shall be prepared by methods that do not change the original structure of the product. Any skins, facings and/or coatings shall be retained. The test specimens shall be representative of the product and preferably not taken closer than 15 mm from the edges o
47、f the product to avoid the influence of any handling damage. For products with non-plane or non-parallel faces, or which have skins, facings and/or coatings, preparation of test specimens shall be as specified in the relevant product standard. The tolerance on parallelism and flatness between the tw
48、o faces of a test specimen shall be not more than 0,5 % of the test specimen side length, with a maximum of 0,5 mm. Before conditioning, the test specimens shall be attached to the two rigid plates or blocks using a suitable adhesive. 6.4 Conditioning of test specimens The test specimens (including
49、the two rigid plates or blocks) shall be conditioned for at least 6 h at (23 5) C. In cases of dispute, they shall be conditioned at (23 2) C and (50 5) % relative humidity for the time specified in the relevant product standard. Other conditions may be used, provided that they give the same results. 7 Procedure 7.1 Test conditions Testing shall be carried out at (23 5) C. In cases of dispute, testing shall be c
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1