1、May 2013 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91.
2、100.60!%$;S“2012448www.din.deDDIN EN 1609Thermal insulating products for building applications Determination of short term water absorption by partial immersion;English version EN 1609:2013,English translation of DIN EN 1609:2013-05Wrmedmmstoffe fr das Bauwesen Bestimmung der Wasseraufnahme bei kurz
3、zeitigem teilweisem Eintauchen;Englische Fassung EN 1609:2013,Englische bersetzung von DIN EN 1609:2013-05Produits isolants thermiques destins aux applications du btiment Dtermination de labsorption deau court terme: essai par immersion partielle;Version anglaise EN 1609:2013,Traduction anglaise de
4、DIN EN 1609:2013-05SupersedesDIN EN 1609:2007-06www.beuth.deDocument comprises 12 pagesIn case of doubt, the German-language original shall be considered authoritative.04.13DIN EN 1609:2013-05 2 A comma is used as the decimal marker. National foreword This document (EN 1609:2013) has been prepared b
5、y Technical Committee CEN/TC 88 “Thermal insulating materials and products” (Secretariat: DIN, Germany) The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Working Committee NA 005-56-60 AA Wrmedmmstoffe. The
6、DIN Standard corresponding to the International Standard referred to in this document is as follows: ISO 5725-2 DIN ISO 5725-2 Amendments This standard differs from DIN EN 1609:2007-06 as follows: a) the standard has been editorially revised. Previous editions DIN EN 1609: 1997-01, 2007-06 National
7、Annex NA (informative) Bibliography DIN ISO 5725-2, Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1609 March 20
8、13 ICS 91.100.60 Supersedes EN 1609:1996English Version Thermal insulating products for building applications - Determination of short term water absorption by partial immersion Produits isolants thermiques destins aux applications du btiment - Dtermination de labsorption deau court terme: essai par
9、 immersion partielle Wrmedmmstoffe fr das Bauwesen - Bestimmung der Wasseraufnahme bei kurzzeitigem teilweisem EintauchenThis European Standard was approved by CEN on 15 December 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving
10、 this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three offici
11、al versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of A
12、ustria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sw
13、eden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national
14、 Members. Ref. No. EN 1609:2013: EEN 1609:2013 (E) 2 Contents Page Foreword . 3 1 Scope 5 2 Normative references . 5 3 Terms and definitions 5 4 Principle 5 5 Apparatus . 5 6 Test specimens 5 6.1 Dimensions of test specimens 5 6.2 Number of test specimens . 6 6.3 Preparation of test specimens . 6 6.
15、4 Conditioning of test specimens. 6 7 Procedure . 6 7.1 Test conditions . 6 7.2 Test procedure . 6 7.2.1 General . 6 7.2.2 Method A (drainage) . 6 7.2.3 Method B (deduction of initial water uptake) 7 8 Calculation and expression of results 8 9 Accuracy of measurement . 9 10 Test report 9 DIN EN 1609
16、:2013-05 EN 1609:2013 (E) 3 Foreword This document (EN 1609:2013) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of
17、 an identical text or by endorsement, at the latest by September 2013, and conflicting national standards shall be withdrawn at the latest by September 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall
18、 not be held responsible for identifying any or all such patent rights. This document supersedes EN 1609:1996. The revision of this standard contains no major changes, only minor corrections and clarifications of an editorial nature. This European Standard is one of a series of standards which speci
19、fy test methods for determining dimensions and properties of thermal insulating materials and products. It supports a series of product standards for thermal insulating materials and products which derive from the Council Directive of 21 December 1988 on the approximation of laws, regulations and ad
20、ministrative provisions of the Member States relating to construction products (Directive 89/106/EEC) through the consideration of the essential requirements. This European Standard has been drafted for applications in building, but it may also be used in other areas where it is relevant. This Europ
21、ean test standard is one of the following group of interrelated standards on test methods for determining dimensions and properties of thermal insulation materials and products, all of which fall within the scope of CEN/TC 88: EN 822, Thermal insulating products for building applications Determinati
22、on of length and width EN 823, Thermal insulating products for building applications Determination of thickness EN 824, Thermal insulating products for building applications Determination of squareness EN 825, Thermal insulating products for building applications Determination of flatness EN 826, Th
23、ermal insulating products for building applications Determination of compression behaviour EN 1602, Thermal insulating products for building applications Determination of the apparent density EN 1603, Thermal insulating products for building applications Determination of dimensional stability under
24、constant normal laboratory conditions (23 C/50 % relative humidity) EN 1604, Thermal insulating products for building applications Determination of dimensional stability under specified temperature and humidity conditions EN 1605, Thermal insulating products for building applications Determination o
25、f deformation under specified compressive load and temperature conditions EN 1606, Thermal insulating products for building applications Determination of compressive creep DIN EN 1609:2013-05 EN 1609:2013 (E) 4 EN 1607, Thermal insulating products for building applications Determination of tensile s
26、trength perpendicular to faces EN 1608, Thermal insulating products for building applications Determination of tensile strength parallel to faces EN 1609, Thermal insulating products for building applications Determination of short-term water absorption by partial immersion EN 12085, Thermal insulat
27、ing products for building applications Determination of linear dimensions of test specimens EN 12086, Thermal insulating products for building applications Determination of water vapour transmission properties EN 12087, Thermal insulating products for building applications Determination of long-term
28、 water absorption by immersion EN 12088, Thermal insulating products for building applications Determination of long-term water absorption by diffusion EN 12089, Thermal insulating products for building applications Determination of bending behaviour EN 12090, Thermal insulating products for buildin
29、g applications Determination of shear behaviour EN 12091, Thermal insulating products for building applications Determination of freeze-thaw resistance EN 12429, Thermal insulating products for building applications Conditioning to moisture equilibrium under specified temperature and humidity condit
30、ions EN 12430, Thermal insulating products for building applications Determination of behaviour under point load EN 12431, Thermal insulating products for building applications Determination of thickness for floating floor insulating products EN 13793, Thermal insulating products for building applic
31、ations Determination of behaviour under cyclic loading EN 13820, Thermal insulating materials for building applications Determination of organic content According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this Euro
32、pean Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slo
33、venia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 1609:2013-05 EN 1609:2013 (E) 5 1 Scope This European Standard specifies the equipment and procedures for determining the short-term water absorption of test specimens by partial immersion. It is applicable to thermal insulatin
34、g products. NOTE It is intended to simulate the water absorption caused by a 24 h raining period during construction work. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references,
35、 only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12085, Thermal insulating products for building applications Determination of linear dimensions of test specimens ISO 5725-2, Accuracy (trueness and precision
36、) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method 3 Terms and definitions This European Standard contains no terms and definitions. 4 Principle A test specimen is placed with its lower part in water,
37、for a period of 24 h, and its change in mass is measured. The excess water adhering to the surface but not absorbed by the test specimen is removed by drainage (method A) or taken into account by deduction of the initial water uptake (method B). 5 Apparatus 5.1 Balance, capable of determining the ma
38、ss of a specimen to an accuracy of 0,1 g. 5.2 Water tank, with a device for keeping the water level constant to within 2 mm, and a device to keep the test specimen in position. The device to keep the test specimen in position shall not cover more than 15 % of the cross-sectional area of the test spe
39、cimen, which is exposed to water. An example is shown in Figure 1. 5.3 Tap water, adjusted to a temperature of (23 5) C. In case of dispute, deionised water shall be used. 5.4 Equipment for drainage. Examples are shown in Figures 2a) and 2b). 6 Test specimens 6.1 Dimensions of test specimens The thi
40、ckness of test specimens shall be the original product thickness. The test specimens shall be prisms of square cross section having a side length of (200 1) mm. DIN EN 1609:2013-05 EN 1609:2013 (E) 6 6.2 Number of test specimens The number of test specimens shall be as specified in the relevant prod
41、uct standard. If the number is not specified, then at least four test specimens shall be used. In the absence of a product standard or any other European Technical Specification, the number of test specimens may be agreed between parties. 6.3 Preparation of test specimens The test specimens shall be
42、 cut so that they do not include product edges. The test specimens shall be prepared by methods that do not change the original structure of the product. Any skins, facings and/or coatings shall be retained. Special methods of preparation, when needed, are given in the relevant product standard or a
43、ny other European Technical Specification. 6.4 Conditioning of test specimens The test specimens shall be conditioned for at least 6 h at (23 5) C. In case of dispute, they shall be conditioned at (23 2) C and (50 5) % relative humidity for the time stated in the relevant product standard. 7 Procedu
44、re 7.1 Test conditions Testing shall be carried out at (23 5) C. In case of dispute, it shall be carried out at (23 2) C and (50 5) % relative humidity. 7.2 Test procedure 7.2.1 General The choice of the method (A or B) shall be as specified in the relevant product standard. In the absence of a prod
45、uct standard or any other European Technical Specification, the method may be agreed between parties. The dimensions of the test specimens shall be measured in accordance with EN 12085. 7.2.2 Method A (drainage) Weigh the test specimen to the nearest 0,1 g to determine its initial mass, m0. Testing
46、shall be carried out with half the number of specimens with one larger face up and the other half with the same larger face down. Place the test specimen in the empty water tank and apply a sufficient load to keep it partially immersed when water is added. Carefully add the water to the tank until t
47、he bottom face of the test specimen is (10 2) mm below the surface of the water (see example in Figure 1). Ensure that the water level remains constant during the test. DIN EN 1609:2013-05 EN 1609:2013 (E) 7 After 24 h 30 min, remove the test specimen; drain it for (10 0,5) min by placing it vertica
48、lly an a mesh, inclined at 45 as shown in Figure 2a) or 2b). Then weigh the test specimen to determine its mass, m24. Key 1 water tank 2 load to keep the test specimen in position 3 test specimen Figure 1 Examples of partial immersion test device a) b) Key 1 stainless steel mesh 2 test specimen 3 pe
49、rforated stainless steel Figure 2 Examples of suitable equipment for drainage 7.2.3 Method B (deduction of initial water uptake) Weigh the test specimen to an accuracy of 0,1 g to determine its initial mass, m0. Testing shall be carried out with half the number of specimens with one larger face up and the other half with the same larger face down. Place the test specimen in the water tank in such position that it is
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1