DIN EN 485-4-1994 Aluminium and aluminium alloys sheet strip and plate part 4 tolerances on shape and dimensions for cold-rolled products German version EN 485-4 1993《铝和铝合金 带材、薄板、板.pdf

1、UDC 669.71-122.2-41 : 669.715.01 8.26-122.2-41 : 621.713.14 DEUTSCHE NORM January 1994 Aluminium and aluminium alloy sheet, strip and plate Tolerances on shape and dimensions for cold-rolled products English version of DIN EN 485 Part 4 c a a a 1 C E L / c : 2 2 C C E C Li E .i i a f C f T i s L a T

2、 r E I 7 u f ; E C C 2 DIN EN 485 Part 4 Aluminium und Aluminiumlegierungen; Bnder, Bleche und Platten: Grenzabmae und Formtoleranzen fr kaltgewalzte Erzeugnisse Supersedes DIN 1783 and parts of 1784, April 1981 editions. European Standard EN 485-4: 1993 has the status of a DIN Standard. A comma is

3、used as the decimal marker. National foreword This standard has been prepared by CEN/TC 132. The responsible German body involved in its preparation was the Normenausschu Nichteisenmetalle (Nonferrous Metals Standards Committee). Standards referred to See Normative references. Previous editions DIN

4、1753: 07.25, 10.27, 12.33, 11.41, 03.54; DIN 1783: 03.40, 12.52, 10.63, 04.81; DIN 1784: 03.40x, 12.52, 04.81; DIN 1784 Part 1 : 10.63; DIN 1793: 12.33, 07.42, 03.54. Amendments In comparison with DIN 1783 and DIN 1784, April 1981 editions, the following amendments have been made. a) Since the scope

5、 of EN 485-4 covers thicknesses above 0,20 mm up to 50 mm, that of DIN 1783 has been restricted to cover thicknesses from 0,02 mm to 0,20 mm, and that of DIN 1784 has been extended to cover thicknesses above 0,20 mm. b) Closer tolerances on flatness have been specified. International Patent Classifi

6、cation B21 BOO1/28 B21 BOO1/36 c 22 c 021/00 G O1 B 021/00 EN comprises 8 pages. euth Verlag GmbH. Berlin. has the exclusive right of sale for German Standards (DIN-Normen). DIN EN 485 Part 4 Engl. Price group 8 Sales No. 1108 08.94 COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed

7、by Information Handling ServicesCOPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesEUROPEAN STANDARD NORME EUROPENNE EUROPAISCHE NORM EN 485-4 October 1993 UDC 669.71 -122.2-41 :669.715.018.26-122.2-41 :621.713.14 Descriptors: Aluminium, aluminium allo

8、ys, sheet, plate, form tolerances, dimensional tolerances, cold-rolled products. English version Aluminium and aluminium alloys Sheet, strip and plate Part 4: Tolerances on shape and dimensions for cold-rolled products Aluminium et alliages d?aluminium; tles, bandes et tles paisses. Partie 4: Tolran

9、ces sur forme et dimensions de produits lamins froid Aluminium und Aluminiumlegierungen; Bnder, Bleche und Platten. Teil 4: Grenzabmae und Formtoleranzen fr kaltgewalzte Erzeugnisse This European Standard was approved by CEN on 1993-10-08. CEN members are bound to comply with the CENKENELEC Internal

10、 Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. T

11、his European Standard exists in three official versions (English, French, German). A version in any other language made by translation underthe responsibilityof a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are th

12、e national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal. Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee

13、 fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels O 1993. Copyright reserved to all GEN members. Ref. No. EN 485-4: 1993 E COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesPage 2 EN 485-4 : 1993 Contents list Page Foreword . 2 2 No

14、rmativereferences . 3 3 Dimensional tolerances . 3 3.1 Thickness 3 3.2 Width . 3 3.3 Length 3 1 scope . . 3 4 Shape tolerances . . 3 4.1 Lateral curvature . 3 4.2 Flatness . 3 4.3 Squareness . . 3 Annex A (normative) Alloy sp nto group I and group II . . . 8 Annex B (normative) Other thickness toler

15、ances . 8 Foreword This European Standard has been prepared by CENTTC 132 Aluminium and aluminium alloys, the Secretariat of which is held by AFNOR. Within its programme of work, Technical Committee CEN/TC 132 entrusted CENTTC 132/WG 7 Sheet, strip and plate to work out the following standard: EN 48

16、5-4 Aluminium and aluminium alloys; sheet, strip and plate. Part 4: Tolerances on shape and dimensions for coid- rolled products This standard is part of a set of four standards. The other standards deal with: EN 485-1 Aluminium and aluminium alloys; sheet, strip and plate. Part 1: Technical conditi

17、ons of inspection and delivery EN 485-2 Aluminium and aluminium alloys; sheet, strip and plate. Part 2: Mechanical properties EN 485-3 Aluminium and aluminium alloys: sheet, strip and plate. Part 3: Tolerances on shape and dimensions for hot- rolled products This European Standard shall be given the

18、 status of a national standard, either by publication of an identical text or by en- dorsement, and conflicting national standards withdrawn, by April 1994 at the latest. The Standard was approved and in accordance with the CENKENELEC Internal Regulations, the following countries are bound to implem

19、ent this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling Servi

20、cesPage 3 EN 485-4 : 1993 1 Scope This Part of EN 485 specifies tolerances on shape and di- mensions for wrought aluminium and aluminium alloy sheet, strip and plate obtained by cold-rolling, for general engineering applications. It applies to products with a thickness over 0,20 mm up to and includi

21、ng 50 mm. It does not apply to semi-finished products in coiled form to be subjected to further rolling (reroll stock), or to special productssuch as corrugated, embossed sheet and strip, or to special applications such as aerospace, can stock etc. which are dealt with in separate European Standards

22、. Technical delivery conditions for products covered by this standard are specified in EN 485-1. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These nor- mative references are cited at the appropriate places in the text

23、 and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For un- dated references, the latest edition of the publication re- ferred to ap

24、plies. EN 485-1 Aluminium and aluminium alloys; sheet, strip and plate. Part 1 : Technical conditions of in- spection and delivery EN 573-3 Aluminium and aluminium alloys; chemical composition and form of wrought products. Part 3: Chemical composition 3 Dimensional tolerances 3.1 Thickness 3.1.1 For

25、 the purposes of this European Standard, the alloys are divided into two groups which correspond to varying difficulty when manufacturing the products. Closer thickness tolerances apply to group I alloys (soft alloys). The grouping is carried out according to the specified chemical composition limit

26、s of the alloys (see EN 573-3) as follows: Group I alloys: - 1 O00 series alloys; - non heat-treatable 7000 and 8000 series alloys; - 4000 series alloys with less than 2% maximum specified silicon content; - 3000 and 5000 series alloys for which the maximum specified magnesium and manganese contents

27、 are each not greater than 1.8 % and their sum not greater than 2,3 %. Group II alloys: The split into group I and group II of the most commonly used general engineering alloys is given in Annex A (see table A.l). - all alloys which do not belong to group I. 3.1.2 Thickness tolerances for sheet, str

28、ip and plate are specified in table 1. 3.1.3 Other thickness tolerances may be agreed between supplier and purchaser. They are specified in Annex B. 3.2 Width 3.2.1 Width tolerances for strip are specified in table 2. 3.2.2 Width tolerances for sheet and plate are specified in table 3. 3.3 Length 3.

29、3.1 Length tolerances for strip are not specified. 3.3.2 Length tolerances for sheet and plate are specified in table 4. 4 Shape tolerances 4.1 Lateral curvature 4.1.1 Lateral curvature tolerances for strip with a width up to and including 3500 mm are specified in table 5. The deviation from straigh

30、tness, d, is measured as indi- cated in figure 1, for a length, L, of 2000 mrn, from one end of the strip, while the strip is resting on a horizontal base- plate. 4.1.2 Lateral curvature tolerances for sheet and plate are specified in table 6. The deviation from straightness, d, is measured as indi-

31、 cated in figure 1, while the sheet or plate is resting on a horizontal baseplate. 4.2 Flatness 4.2.1 Flatness tolerances for strip are not specified. 4.2.2 Flatness tolerances for sheet and plate are speci- fied in table 7 and are expressed as a percentage of the length, L, and/or the width, W, and

32、/or the measured chord length, 1. Deviation from flatness, d, resulting from arching, buckling or egde waves, is measured as shown in figures 2 to 5, using a lightweight straightedge and a feeler gauge, dial gauge or scale, while the sheet or plate is resting on a horizontal baseplate, with its conc

33、ave side facing up- wards. These tolerances do not apply to sheet and plate supplied in the O (annealed) or F (asfabricated) tempers, or to bright sheet. These tolerances do not include end or corner turn-up. 4.3 Squareness 4.3.1 Squareness tolerances for strip are not specified. 4.3.2 Squareness to

34、lerances for sheet and plate are specified in table8. The squareness tolerance is ex- pressed as the maximum allowable difference in length of diagonals AA and BB as shown in figure 6. COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesPage 4 EN 485-4:

35、 1993 Specified thickness Table 1: Thickness tolerances Dimensions in millimetres Over 1000 Over 1250 Over 1600 Over 2000 Over 2500 Over 3000 Upto1000 upto 1250 UptO 1600 upto 2000 upto 2500 upto 3000 upto 3500 Alloy group I Thickness tolerance for specified width COPYRIGHT DIN DEUTSCHES Institut Fu

36、r Normung E.V.- EnglishLicensed by Information Handling ServicesPage 5 EN 485-4: 1993 Specified thickness Over up to 0.20 0,6 Tolerance for specified width - Over 100 Over 300 Over 500 Over 1250 Over 1650 Up to100 upto 300 upto 500 up to 1250 up to 1650 upto 2600 + 0,3 + 0.4 + 0.6 + 1.5 + 2.5 +3 O O

37、 O O O 0 0,6 1 ,o I + 0.3 + 0.5 +1 + 1.5 + 2.5 +3 + 0.4 + 0.7 + 1.2 +2 + 2.5 +3 1 ,o O O O O O 0 2,o O O O O O 0 Table 3: Width tolerances for sheet and plate Dimensions in millimetres 2,o 3,O +1 +l + 1,5 +2 + 2.5 +4 + 15 +2 +3 +3 +5 3,O O O O O O 0 5,o O O O O 0 - 1 Specified thickness Over up to 0

38、,20 3,O 3,O 6,O 6,O 50 Table 5: Lateral curvature tolerances for strip (measured on 2000 rnrn strip length) Dimensions in millimetres Tolerance for specified width Over 500 Over 1250 Over 2000 Over 3000 Upto500 upto 1250 upto 2000 upto 3000 upto 3500 + 1.5 +3 +4 +5 - O O O O +3 +4 +5 +8 +8 O O O O 0

39、 +4 +5 +5 +8 +8 O O O O 0 Specified thickness Over up to 0,20 30 3,o 6,O 6,O 50 300 I 600 Tolerance for specified length Over 1 O00 Over 2000 Over 3000 Over 5000 Upto1000 upto 2000 upto 3000 up to 5000 +3 +4 +6 +8 O O O O +4 +6 +a + 10 O O O O +6 +8 + 10 + 10 O O O O + 0,2 % of specified length I 5

40、Specified width Over up to 2 25) 1 O0 1 O0 300 I 600 I 1 O00 I 4 Lateral curvature, dlnax 8 6 1 O00 2 O00 2 O00 3 3 500 3 1) For widths less than 25 rnrn, the tolerances are to be agreed betweei purchaser and supplier. COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information

41、 Handling ServicesPage 6 EN 485-4: 1993 Upto 1000 2 Table 6 Lateral curvature tolerances for sheet and plate Dimensions in millimetres Lateral curvature, d, for specified length, L Over 1 O00 Over 2000 Over 3500 Over 5000 upto 2000 upto 3500 upto 5000 upto 15000 - - 4 8 Specified width Over 1 up to

42、600 1 O00 2 O00 - 2100) I 1 O00 1 2 4 5 2 O00 - 3 500 0,l % length 2 4 5 of specified 4 5 - - 300 Specified length Over up to 1 O00 - Squareness tolerance for specified width Specified thickness Over 1 O00 Over 1500 Over 2000 Up to 1000 up to 1500 up to 2000 up to 3500 - - - 6 5 - - - . .6 1) For wi

43、dths less than 100mm, the tolerances are to be agreed between purchaser and supplier. - 6 7 8 Table 7: Flatness tolerances for sheet and plate I 1 I 56 6 2000 1 3000 Specified thickness mm 5 5 7 8 7 7 9 10 Total deviation Partial deviation % % (for a chord of at least 300 mm) on length on width drna

44、xiL drnadw By agreement 3 O00 5 O00 S6 6 8 8 10 6 8 10 10 12 $6 10 10 12 12 6 12 12 15 15 5 O00 15 O00 1000 1 2000 COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesPage 7 EN 485-4 : i 993 -a I Side edge (concave side) Straightedge / Or sheet d = devi

45、ation from straightness L = length of sheet or plate Figure 1: Lateral curvature of plate or sheet of length L (see 4.1.2) A- A d = deviation from flatness W = width of sheet or plate Figure 2: Transverse arch (see 4.2.2) , 1 -1 I L A-A d = deviation from flatness L = length of sheet or plate Figure

46、 3: Longitudinal arch (see 4.2.2) c. I. COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesPage 8 EN 485-4:1993 *I I I IA I 1 I A-A d = deviation from flatness 1 = length of buckle (chord) Figure 4 Buckles (see 4.2.2) A -A d = deviation from flatness 1

47、 = length of edge wave (chord) Figure 5: Edge wave (see 4.2.2) Figure 6 Measurement of squareness (see 4.3.2) Annex A (normative) Alloy split into group I and group II Table A.1: Alloy groups 1080A 1070A 1050A 1200 3003 3103 3005 3105 4006 4007 5005 5050 8011A 2014 2017A 2024 3004 5040 5049, 5251 50

48、52 5154A 5454 5754 5182 5082 5086 6061 6082 7020 7021 7022 7075 Amex B (normative) Other thickness tolerances If agreed between supplier and purchaser, group I alloys may be supplied with group II thickness tolerances. COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling Services