DIN EN 508-3-2009 Roofing products from metal sheet - Specification for self-supporting products of steel aluminium or stainless steel sheet - Part 3 Stainless steel English versio.pdf

1、July 2009DEUTSCHE NORM English price group 16No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91.060.20!$Xtn“1538175www

2、.din.deDDIN EN 508-3Roofing products from metal sheet Specification for self-supporting products of steel, aluminium orstainless steel sheet Part 3: Stainless steelEnglish version of DIN EN 508-3:2009-07Dachdeckungsprodukte aus Metallblech Festlegungen fr selbsttragende Bedachungselemente aus Stahlb

3、lech, Aluminiumblechoder nichtrostendem Stahlblech Teil 3: Nichtrostender StahlEnglische Fassung DIN EN 508-3:2009-07SupersedesDIN EN 508-3:2000-12www.beuth.deDocument comprises 40 pages2 National foreword This standard has been prepared by Technical Committee CEN/TC 128 “Roof covering products for

4、discontinuous laying and products for wall cladding” (Secretariat: NBN, Belgium). The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Technical Committee NA 005-02-06 AA Dacheindeckungsprodukte aus Metallblech

5、 (Sp CEN/TC 128/SC 7). Amendments This standard differs from DIN EN 508-3:2000-12 as follows: a) The standard has been revised in form and substance. b) Annex D has been deleted. Previous editions DIN EN 508-3: 2000-12 DIN EN 508-3:2009-07 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 508-3 J

6、uly 2008 ICS 91.060.20 Supersedes EN 508-3:2000 English Version Roofing products from metal sheet Specification for self-supporting products of steel, aluminium or stainless steel sheet Part 3: Stainless steel Produits de couverture en tle mtallique Spcification pour les plaques de couverture en tle

7、 dacier, daluminium ou dacier inoxydable Partie 3: Acier inoxydable Dachdeckungsprodukte aus Metallblech Festlegungen fr selbsttragende Bedachungselemente aus Stahlblech, Aluminiumblech oder nichtrostendem Stahlblech Teil 3: Nichtrostender Stahl This European Standard was approved by CEN on 30 May 2

8、008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained

9、 on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management

10、 Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

11、Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form an

12、d by any means reserved worldwide for CEN national Members. Ref. No. EN 508-3:2008: EEN 508-3:2008 (E) 2 Contents Page Foreword4 Introduction .5 1 Scope 6 2 Normative references 6 3 Terms and definitions, symbols and abbreviations.6 3.1 General6 3.2 Materials .6 3.3 Profiles7 3.4 Product geometry 9

13、3.5 Symbols and abbreviations 13 4 Requirements.13 4.1 General13 4.2 Materials .13 4.2.1 Grades.13 4.2.2 Chemical composition 14 4.2.3 Physical properties14 4.2.4 Surface finishes of stainless steel.14 4.2.5 Tin coated stainless steel .14 4.2.6 Organic coated stainless steel.14 4.3 Products .15 4.3.

14、1 Mechanical resistance.15 4.3.2 Calculation and tests of mechanical resistance.15 4.3.3 Dimensions.15 4.3.4 Dimensional tolerances for the profiled sheets .16 4.3.5 Safety in case of fire16 5 Test methods16 5.1 Material properties.16 5.2 Structural properties .16 6 Designation 16 7 Marking, labelli

15、ng and packaging 17 7.1 Marking and labelling 17 7.2 Packaging and special ordering conditions .17 7.3 Transport, storage and handling17 Annex A (informative) Physical properties.18 Annex B (normative) Dimensional tolerances .19 B.1 Tolerances for trapezoidal sheets19 B.1.1 General19 B.1.2 Depth of

16、profile 19 B.1.3 Depth of stiffeners .20 B.1.4 Pitch 20 B.1.5 Widths of crown and valley 21 B.1.6 Cover width 21 B.1.7 Radius of bends.22 B.1.8 Deviation from straightness .23 B.1.9 Deviation from squareness.24 B.1.10 Length .24 B.1.11 Deviation of side lap25 DIN EN 508-3:2009-07 EN 508-3:2008 (E) 3

17、 B.1.12 Curve radius and angles.25 B.2 Tolerances for sinusoidal profiles.26 B.3 Tolerances on tiles 26 B.3.1 General .26 B.3.2 Depth of tile27 B.3.3 Web angular displacement (Figure B.12)28 B.3.4 Pitch28 B.3.5 Width of crown and valley (Figure B.14).29 B.3.6 Cover width 29 B.3.7 Radius of bends.29

18、B.3.8 Deviation from straightness.30 B.3.9 Deviation from squareness 31 B.3.10 Length.31 B.3.11 Contraction or bulging31 B.4 Methods for measuring profiles.32 B.4.1 General .32 B.4.2 Depth of profile 32 B.4.3 Depth of stiffeners.33 B.4.4 Pitch33 B.4.5 Width of crown and valley 34 B.4.6 Cover width 3

19、4 B.4.7 Radius of bends.34 B.4.8 Straightness.34 B.4.9 Squareness 34 B.4.10 Length.35 B.4.11 Side laps.35 B.4.12 Side lap ripple 35 Annex C (informative) Test methods for concentrated load 37 Bibliography38 Page DIN EN 508-3:2009-07 EN 508-3:2008 (E) 4 Foreword This document (EN 508-3:2008) has been

20、 prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying and products for wall cladding”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement

21、, at the latest by January 2009, and conflicting national standards shall be withdrawn at the latest by January 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying

22、 any or all such patent rights. This document supersedes EN 508-3:2000. EN 508 Roofing products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet consists of the following parts: Part 1: Steel; Part 2: Aluminium; Part 3: Stainless steel. Accor

23、ding to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvi

24、a, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 508-3:2009-07 EN 508-3:2008 (E) 5 Introduction Figure 1 indicates the position of this standard in the CEN framework of standards concerning

25、roofing products of metal. Roofing products of metal Self-supporting products Fully supported products EN 14782 Copper / Zinc EN 506 Steel EN 508-1 Aluminium EN 508-2 Stainless steel EN 508-3 Figure 1 Framework of standards In this standard the performance of the product has been defined in terms of

26、 calculation and a number of type tests. The performance of a roof constructed with these products depends not only on the properties of the product as required by this standard, but also on the design, construction and performance of the roof as a whole in relation to the environment and conditions

27、 of use. DIN EN 508-3:2009-07 EN 508-3:2008 (E) 6 1 Scope This Part of EN 508 specifies requirements for self-supporting roofing products for discontinuous laying made from stainless steel sheet with or without additional metallic and/or organic coatings. The standard establishes general characteris

28、tics, definitions, classifications and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that th

29、e products comply before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions. The standard applies to all discontinuously laid self-supporting external profiled sheets for roofing with the exception of tiles with a

30、surface area less than 1 m2and produced by stamping. These profiled roof sheets are designed to keep wind, rain and snow out of the building and to transfer any resultant loads and infrequent maintenance loads to the structure. No requirements for supporting construction, design of roof system and e

31、xecution of connections and flashings are included. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including

32、 any amendments) applies. EN 10088-1, Stainless steels - Part 1: List of stainless steels EN 10088-2, Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 10202, Cold reduced tinmill products Electrolytic tinplate an

33、d electrolytic chromium/chromium oxide coated steel EN ISO 9445, Continuously cold-rolled stainless steel narrow strip, wide strip, plate/sheet and cut lengths - Tolerances on dimensions and form (ISO 9445:2002) 3 Terms and definitions, symbols and abbreviations For the purposes of this document, th

34、e following terms and definitions apply. 3.1 General 3.1.1 self-supporting product Product which will, by virtue of its material and shape, support all applied loadings (e.g. snow, wind, foot traffic) and transmit these loadings to spaced structural supports. 3.2 Materials 3.2.1 stainless steel stee

35、l sheets with at least a content of 10,5 % chromium and max 1,2 % carbon NOTE For roofing products the stainless steel grades are: DIN EN 508-3:2009-07 EN 508-3:2008 (E) 7 ferritic; austenitic with or without molybdenum; austenitic ferritic (duplex); and higher alloyed grades. 3.2.2 terne coated sta

36、inless steel stainless steel continuously hot dip coated with a lead-tin alloy 3.2.3 tin coated stainless steel stainless steel continuously coated with tin by electrodeposition 3.2.4 organic coated stainless steel stainless steel, terne coated stainless steel or tin coated stainless steel which is

37、continuously (factory-)painted by roller or spray process NOTE EN 10169-1 refers to this type of coated steel. 3.3 Profiles 3.3.1 trapezoidal profiled sheet self-supporting sheet which is designed to allow it to be side and end lapped, the crowns of which may be rounded and, in addition, the crowns,

38、 webs and valleys may be stiffened NOTE See Figures 2 to 5. Figure 2 Part of typical trapezoidal profile Figure 3 Part of typical trapezoidal profile with rounded crowns Figure 4 Part of typical trapezoidal profile with stiffened crown and web DIN EN 508-3:2009-07 EN 508-3:2008 (E) 8 Figure 5 Part o

39、f typical trapezoidal profile with stiffened valley 3.3.2 sinusoidal profiled sheet self-supporting sheet which is designed to allow it to be side and end lapped, comprising a series of arc shaped crowns and valleys interconnected with tangential webs NOTE See Figure 6. Figure 6 Part of typical sinu

40、soidal profiled sheet 3.3.3 standing seam and concealed fix sheet self-supporting sheet profiled in such a way that the fixings are hidden within the construction and are not exposed to the weather NOTE 1 See Figures 7 and 8. NOTE 2 The profile shape is designed to allow the formation of side laps o

41、n site. NOTE 3 As these types of roof covering products are used in proprietary roofing systems, no structural requirements are given within the present standard. NOTE 4 These products are normally designed by testing. Figure 7 Typical standing seam profile DIN EN 508-3:2009-07 EN 508-3:2008 (E) 9 F

42、igure 8 Typical concealed fix profile 3.3.4 tile profiles parts of typical tile profiled sheets that can allow the sheet to be side and/or end lapped NOTE 1 See figures 9a, 9b and 9c. NOTE 2 The tile profiles may include transverse steps. NOTE 3 As these types of roof covering products are used in p

43、roprietary systems no structural requirements are given within this standard. NOTE 4 These products are normally designed by testing. Figure 9 Typical tile profiles 3.4 Product geometry NOTE The names for various parts of typical trapezoidal profiled sheets are given in Figures 10a) and 10b), with a

44、dditional definitions for sinusoidal profiles in Figure 11 and tile profiles in Figure 12. DIN EN 508-3:2009-07 EN 508-3:2008 (E) 10 Key 1 Cover width 7 Depth 2 Valley stiffener 8 Valley 3 Rib 9 Pitch 4 Web stiffener 10 Crown 5 Trough 11 Drainage groove 6 Web 12 Crown stiffener a) Definitions of the

45、 parts of typical trapezoidal profiled sheets DIN EN 508-3:2009-07 EN 508-3:2008 (E) 11 Key 1 Bend radius 4 Overlap 2 End lap 5 Underlap 3 Web angle 6 Side lap in principle the same on tiles b) Definitions of the parts of typical trapezoidal profiled sheets Figure 10: Definitions of the parts of typ

46、ical profiled sheets DIN EN 508-3:2009-07 EN 508-3:2008 (E) 12 Key 1 Depth 2 Pitch Key 1 Height of the step 2 Length of the step 3 Number of steps 4 End lap DIN EN 508-3:2009-07 Figure 11 Definitions of the parts of typical sinusoidal profiled sheets Figure 12 Definitions of the parts of typical til

47、e EN 508-3:2008 (E) 13 3.5 Symbols and abbreviations X Stainless steel X. +T Terne coated stainless steel X .+SE Terne coated stainless steel SP Polyester paint coating SP-SI Silicone-modified polyester paint coating PVDF Polyvinylidene fluoride paint coating PUR Polyurethane paint coating PUR-PA Po

48、lyurethane-modified polyester paint coating PVC(P) Polyvinylchloride(plastisol) coating applied by coil coating process PVC(F) Polyvinylchloride (plastisol) film coating PVF(F) Polyvinylfluoride film coating PE(F) Polyethylene film coating PET(F) Polyethylene terephthalate film coating PP(F) Polypro

49、pylene film coating 4 Requirements 4.1 General The product shall be manufactured from materials complying with Subclause 4.2 NOTE 1 The supplier of the materials is responsible for carrying out the tests necessary to verify that the materials supplied to the manufacturer comply with the requirements and should provide appropriate inspection documents (according to EN 10204) on request. NOTE 2 The symbols and abbreviations to be used to designate the steel grade, the type and mass of the metallic coating are those