1、June 2013 Translation by DIN-Sprachendienst.English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 97
2、.220.40!%$l“2017391www.din.deDDIN EN 567Mountaineering equipment Rope clamps Safety requirements and test methods;English version EN 567:2013,English translation of DIN EN 567:2013-06Bergsteigerausrstung Seilklemmen Sicherheitstechnische Anforderungen und Prfverfahren;Englische Fassung EN 567:2013,E
3、nglische bersetzung von DIN EN 567:2013-06Equipement dalpinisme et descalade Bloqueurs Exigences de scurit et mthodes dessai;Version anglaise EN 567:2013,Traduction anglaise de DIN EN 567:2013-06SupersedesDIN EN 567:1997-04www.beuth.deDocument comprises 14 pagesIn case of doubt, the German-language
4、original shall be considered authoritative.06.13 DIN EN 567:2013-06 2 A comma is used as the decimal marker. Start of application The start of application of this standard is 2013-06-01. National foreword This standard includes safety requirements within the meaning of the Produktsicherheitsgesetz (
5、ProdSG) (German Product Safety Act). This document (EN 567:2013) has been prepared by Technical Committee CEN/TC 136 “Sports, playground and other recreational facilities and equipment” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Sport
6、- und Freizeitgert, Working Committee NA 112-04-05 AA Bergsteigerausrstung. Where this standard has been identified by the Ausschuss fr Produktsicherheit (German Committee for Product Safety) and reference to it has been published in the Gemeinsames Ministerialblatt (German Joint Ministerial Gazette
7、) by the Bundesanstalt fr Arbeitsschutz und Arbeitsmedizin (BAuA) (German Federal Institute for Occupational Safety and Health), it is to be presumed that rope clamps which comply with this standard fulfil the relevant health and safety requirements. Where they comply with the provisions laid down i
8、n Section 5 of the Product Safety Act, such products may then be marked with the GS mark (German “safety tested” mark) as awarded to the manufacturer by an authorized “GS organization”. Amendments This standard differs from DIN EN 567:1997-04 as follows: a) the standard has been editorially revised.
9、 b) new test methods have been introduced to test the prevention of an accidental detachment of the rope from the rope clamp; c) Annex A “Standards on mounteneering equipment” has been updated. Previous editions DIN 33947: 1988-12 DIN EN 567: 1993-01, 1997-04 EUROPEAN STANDARD NORME EUROPENNE EUROPI
10、SCHE NORM EN 567 March 2013 ICS 97.220.40 Supersedes EN 567:1997English Version Mountaineering equipment - Rope clamps - Safety requirements and test methods Equipement dalpinisme et descalade - Bloqueurs - Exigences de scurit et mthodes dessai Bergsteigerausrstung - Seilklemmen - Sicherheitstechnis
11、che Anforderungen und Prfverfahren This European Standard was approved by CEN on 12 January 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to
12、-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translat
13、ion under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland,
14、Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION CO
15、MIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 567:2013: EEN 567:2013 (E) 2 Contents Page Foreword 3 Introductio
16、n .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Safety requirements 5 4.1 Design .5 4.2 Strength 6 5 Test methods 6 5.1 Test conditions 6 5.2 Examination of design 6 5.2.1 General 6 5.2.2 Function 6 5.2.3 Attachment .6 5.3 Strength test .7 5.3.1 Determination of the strength 7 5
17、.3.2 Pushing test .7 5.3.3 Pulling test 8 6 Marking .8 7 Information supplied by the manufacturer .9 Annex A (informative) Standards on mountaineering equipment . 10 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 89/686/EEC Personal
18、protective equipment . 11 Bibliography . 12 DIN EN 567:2013-06 EN 567:2013 (E) 3 Foreword This document (EN 567:2013) has been prepared by Technical Committee CEN/TC 136 “Sports, playground and other recreational facilities and equipment”, the secretariat of which is held by DIN. This European Stand
19、ard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2013, and conflicting national standards shall be withdrawn at the latest by September 2013. Attention is drawn to the possibility that some of the elements
20、of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 567:1997. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Tr
21、ade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. In comparison with the previous edition EN 567:1997, the following significant changes have been made: a) editorial re
22、vision; b) introduction of new test methods to test the prevention of an accidentally detachment of the rope from the rope clamp; c) update of Annex A. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this Europ
23、ean Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slov
24、enia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 567:2013-06 EN 567:2013 (E) 4 Introduction The text is based on UIAA-Standard 126 (International Mountaineering and Climbing Federation), which has been developed with international participation. This European Standard is one o
25、f a package of standards for mountaineering equipment, see Annex A. DIN EN 567:2013-06 EN 567:2013 (E) 5 1 Scope This European Standard applies to rope clamps used with dynamic mountaineering ropes according to EN 892 or accessory cord according to EN 564 and low stretch kernmantel ropes according t
26、o EN 1891. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (includin
27、g any amendments) applies. EN 564, Mountaineering equipment Accessory cord Safety requirements and test methods EN 892, Mountaineering equipment Dynamic mountaineering ropes Safety requirements and test methods EN 1891, Personal protective equipment for the prevention of falls from a height Low stre
28、tch kernmantel ropes 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 rope clamp mechanical device which, if attached to a rope or an accessory cord of appropriate diameter, will clamp under load in one direction and move freely in the opposit
29、e direction 3.2 locking device device that, when closed around a rope, prevents the unintended removal of the rope from the rope clamp 4 Safety requirements 4.1 Design 4.1.1 Rope clamps shall have a locking device or similar mechanism that, if closed prevents a rope or an accessory cord with a diame
30、ter within the range marked on the rope clamp (see Clause 6) from being removed from the rope clamp. The rope clamps shall be designed in such a way that when used in accordance with the manufacturers instructions, at least two independent actions shall be needed, before the rope or accessory cord c
31、an be released from the rope clamp. 4.1.2 When tested according to 5.2.2 rope clamps shall clamp onto a rope or an accessory cord in one direction and to move freely in the opposite direction. 4.1.3 When tested according to 5.3.1 rope clamps shall not completely break the rope or accessory cord. 4.1
32、.4 When tested according to 5.2.3 rope clamps shall have an attachment point of at least diameter 13 mm (see Figure 1). The edges of all openings for handles and connectors or sling attachment shall be as shown in Figure 1. 4.1.5 When tested according to 5.2.1 all edges of a rope clamp shall be free
33、 of burrs. DIN EN 567:2013-06 EN 567:2013 (E) 6 4.2 Strength 4.2.1 When tested according to 5.3.1, rope clamps with a rope or accessory cord of diameter within the range marked on the rope clamp (see Clause 6) attached shall show no visible signs of damage or deformation which can impair its functio
34、n. Dimensions in millimetres Figure 1 Edges of openings 4.2.2 When tested according to 5.3.2 the rope or accessory cord shall not be detached from the rope clamp at the force of at least 400 N. 4.2.3 When tested according to 5.3.3 the rope or accessory cord shall not be detached from the rope clamp
35、at the force of at least 2 000 N. 5 Test methods 5.1 Test conditions Carry out the tests at a temperature of (23 5) C. 5.2 Examination of design 5.2.1 General Test by tactile examination that the edges of the rope clamp are free of burrs. 5.2.2 Function With the locking device closed and a rope or a
36、ccessory cord of maximum diameter, as marked on the rope clamp, check that the rope or accessory cord cannot be removed sideways. Check also, by pulling by hand, that the rope clamp locks in one direction and can slip in the opposite direction. Repeat the checks using a rope or accessory cord of min
37、imum diameter as marked on the rope clamp. 5.2.3 Attachment Determine the dimension of the attachment opening (see 4.1.4) by measuring with a bar of (1301,00+) mm diameter. DIN EN 567:2013-06 EN 567:2013 (E) 7 5.3 Strength test 5.3.1 Determination of the strength Attach a rope according to EN 892 or
38、 EN 1891 or accessory cord according to EN 564 of maximum diameter as marked on the rope clamp, to the rope clamp as specified by the manufacturer and a connector in the attachment point of the rope clamp. Fix the system in a tensile testing machine and load it with a force of (4 0,1) kN using a tes
39、t speed of (100 50) mm/min. Release the load immediately. Repeat four more times. Move the rope clamp between application of each force, so that the locking force is applied to a previously unloaded point of the rope or accessory cord in each case. Repeat the procedure using a rope or accessory cord
40、 of minimum diameter, as marked on the rope clamp. Note any visible signs of damage or deformation, which can impair its function. 5.3.2 Pushing test Attach a loop of rope according to EN 892 or EN 1891 or accessory cord according to EN 564 of maximum diameter as marked on the rope clamp to the rope
41、 clamp as specified by the manufacturer and a connector in the upper hole of the rope clamp (see Figure 2). If there is no upper hole, clamp or use any other means of attachment without influence on the test. Fix the system in a tensile testing machine and load it with a force of (400 10) N, using a
42、 test speed of (100 50) mm/min. Release the load immediately. Repeat the procedure using a rope or accessory cord of minimum diameter, as marked on the rope clamp. Note any visible signs of damage or deformation, which can impair its function. Figure 2 Pushing test DIN EN 567:2013-06 EN 567:2013 (E)
43、 8 5.3.3 Pulling test Attach a rope according to EN 892 or EN 1891 or accessory cord according to EN 564 of maximum diameter as marked on the rope clamp to the rope clamp as specified by the manufacturer and a connector in the hole of the rope clamp (see Figure 3). Fix the system in a tensile testin
44、g machine and load it with a force of (2 0,01) kN using a test speed of (100 50) mm/min. Release the load immediately. The slack on the untensioned strand shall be at least 100 mm (see Figure 3). Repeat the procedure using a rope or accessory cord of minimum diameter, as marked on the rope clamp. No
45、te any visible signs of damage or deformation, which can impair its function. Figure 3 Pulling test 6 Marking Rope clamps shall be marked with at least the following information: a) name of the manufacturer or its authorised representative; NOTE For a definition of manufacturer and authorised repres
46、entative see Regulation 765/2008 1. b) range of rope or accessory cord diameters, in millimetres, to the nearest whole number, with which the rope clamp can be used. The symbol shall be used as a prefix to indicate the diameter, e.g. 7 mm to 11 mm; c) pictogram showing the direction of use; d) graph
47、ical symbol (see Figure 4), which advises the user to read the information given by the manufacturer. Figure 4 Operators manual (according to ISO 7000, Symbol No. 1641) DIN EN 567:2013-06 EN 567:2013 (E) 9 7 Information supplied by the manufacturer The information supplied by the manufacturer shall
48、contain at least the following elements: a) name and address of the manufacturer or its authorised representative 1; b) reference number of this European Standard: EN 567; c) the meaning of any markings on the product; d) the use of the product; 1) how to choose other components for use in the syste
49、m, e.g. how to select the right type and diameter of rope; 2) how to insert and extract the rope or accessory cord; 3) how the locking device works; 4) where and how to attach to the rope clamp; e) how to maintain and service the product; f) the lifespan of the product and factors affecting the lifespan; g) advice that the product shall only be used by trained and/or otherwise competent persons or the user should be under the direct supervision of a trained and/or otherwise competent persons; h) the effects of
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1