DIN EN 603-3-2000 Aluminium and aluminium alloys - Wrought forging stock - Part 3 Tolerances on dimensions and form German version EN 603-3 2000《铝和铝合金 锻造坯料 第3部分 尺寸和形状公差》.pdf

1、DEUTSCHE NORM June 2000 Aluminium and aluminium alloys - Wrought forging stock Part 3: Tolerances on dimensions and form English version of DIN EN 603-3 DIN - EN 603-3 ICs 77.150.10 Aluminium und Aluminiumlegierungen - Stranggepresstes oder gewalztes Schmiedevormaterial - Teil 3: Grenzabmae und Form

2、toleranzen European Standard EN 603-3 : 2000 has the status of a DIN Standard. A comma is used as the decimal marker. National foreword This standard has been prepared by CEN/TC 132. The responsible German body involved in its preparation was the Normenausschuss Nichteisenmetalle (Nonferrous Metals

3、Standards Committee), Technical Committee Schmiedestcke. EN comprises 19 pages. No pari of this standard may be reproduced without the prior permission of Ref. No. DIN EN 603-3 : 2000-0 Y Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, s the exclusive right of

4、sale for German Standards (DIN-Normen). English price group 11 Sales No. 11 11 10.00 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 603-3 March 2000 ICs 77.150.10 English version Aluminium and aluminium alloys - Wrought forging stock Part 3: Tolerances on dimensions and form Aluminium et allia

5、ges daluminium - Produits corroys destins la forge - Partie 3: Tolrances sur dimensions et forme Aluminium und Aluminiumlegie- rungen - Stranggepresstes oder gewalztes Schmiedevormaterial - Teil 3: Grenzabmae und Formtoleranzen This European Standard was approved by CEN on 2000-02-1 7 CEN members ar

6、e bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stand- ards may be obtained on application to

7、 the Central Secretariat or to any CEN member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same st

8、atus as the official versions. CEN members are the national standards bodies of Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. CEN European Co

9、mmittee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels O 2000. CEN - All rights of exploitation in any form and by any means reserved worldwide for CEN national members. Ref. No. EN 603-3 : 2000 E Page 2 EN 6

10、03-3 : 2000 Contents Foreword 2 1 Scope 3 2 Normative references 3 Terms and definitions . 3 3 4 Dimensional ranges 3 5 Alloys 4 5.1 Chemical composition 4 5.2 Alloy groups 4 6 Tolerances on dimensions and form 5 6.1 General . 5 6.2 Extruded round bar . 5 6.3 Extruded square bar . 7 6.4 Extruded rec

11、tangular bar 12 6.5 Hot rolled plate 18 Bibliography 19 Foreword This European Standard has been prepared by Technical Committee CENITC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. Within its programme of work, Technical Committee CENITC 132 entrusted CENTTC 132NV

12、G 3 “Forgings and cast and wrought forging stock” to prepare the following Standard: EN 603-3, Aluminium and aluminium alloys - Wrought forging stock - Part 3: Jolerances on dimensions and form This standard is part of a set of three standards. The other standards deal with: EN 603- i , Aluminium an

13、d aluminium alloys - Wrought forging stock - Part i: Techntcal conditions for inspection and delivery EN 603-2, Aluminium and aluminium alloys - Wrought forging stock - Part 2: Mechanicalproperties This European Standard shall be given the status of a national standard, either by publication of an i

14、dentical text or by endorsement, at the latest by September 2000, and conflicting national standards shall be withdrawn at the latest by September 2000. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. This Euro

15、pean Standard is considered to be a supporting standard to those application and product standards which in themselves support an essential safety requirement of a New Approach Directive and which make reference to this European Standard. According to the CENKENELEC Internal Regulations, the nationa

16、l standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Page

17、 3 EN 603-3 : 2000 1 Scope This part of EN 603 specifies the tolerances on dimensions and form of wrought aluminium and aluminium alloy forging stock. It applies to extruded and rolled products. 2 Normative references This standard incorporates, by dated or undated reference, provisions from other p

18、ublications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this standard only when incorporated in it by amendment or revision. Fo

19、r undated references, the latest edition of the publication referred to applies. EN 573-3, Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3 : Chemical composition EN 573-4, Aluminium and aluminium alioys - Chemical composition and form of wrought products -

20、 Part 4 Form of products EN 603- 1, Aluminium and aluminium alloys - Wrought forging stock - Parf 1 : Technical conditions for inspection and delivery EN 603-2, Aluminium and aluminium alloys - Wrought forging stock - Part 2 : Mechanical properties EN 12258-1, Aluminium and aluminium alloys - Terms

21、and definifions - Part 1 : General terms 3 Terms and definitions For the purposes of this part of this European Standard the terms and definitions given in EN 12258-1 apply. 4 Dimensional ranges The tolerances on dimensions and form expressed in this European Standard cover extruded products of regu

22、lar cross-section in the form of round bars having diameters up to and including 320 mm, square bars having width across flats up to and including 220 mm, rectangular bars having widths up to and including 600 mm in thicknesses up to and including 240 mm and hot rolled plate in widths up to and incl

23、uding 3 500 mm in thicknesses from 1 O mm up to and including 200 mm. Tolerances on dimensions and form of such products in excess of these ranges shall be subject to agreement between supplier and purchaser and stated on the order or drawing. Page 4 EN 603-3 : 2000 5 Alloys 5.1 Chemical composition

24、 The chemical composition limits of the alloys shall be as specified in EN 573-3. 5.2 Alloy groups For the purposes of this part of this European Standard the alloys are divided into two groups which correspond to varying difficulty when manufacturing the extruded forging stock. The division into Gr

25、oup I and Group II of these alloys is specified in Table 1. The division into Class A and Class B alloys shall be as specified in EN 573-4. Class A covers aluminium and aluminium alloys produced in large volume as wrought forging stock for which mechanical properties are specified in EN 603-2. Class

26、 B covers aluminium and aluminium alloys produced in limited volume as wrought forging stock for which mechanical properties are not specified. Table 1 - Alloy Groups Alloy Group I (extrude with I Alloy designation EN AW-1050A Al 99,5 EN AW-6005A AI SiMg(A) EN AW-6060 AI MgSi EN AW-6061 AI MglSiCu E

27、N AW-6082 AI Sil MgMn ice) Class B B B B A Other alloys shall be grouped as follows : Alloy Group I - unalloyed aluminium - alloys AI Mn - alloys AI Mg with a maximum of 2,8% Mg - alloys AI MgSi Alloy Group II (difficult to ext Alloy designation EN AW-2011 AI CuGBiPb EN AW-2014 EN AW-2017A EN AW-261

28、8A EN AW-2219 EN AW-2024 EN AW-2031 EN AW-4032 EN AW-5454 EN AW-5754 EN AW-5019 EN AW-5083 EN AW-701 O EN AW-7012 EN AW-7020 EN AW-7075 AI Cu4SiMgI AI CuMgSi(A) AI Cu2Mg1,5Ni AI CuGMn AI Cu4MglI AI Cu2,5NiMg AI Sil2,5MgCuNi AI Mg3MnI Al Mg31 Al Mg51 AI Mg4,5Mn0,7 AI ZnGMgCu AI Zn6Mg2Cuj AI Zn4,5Mgl

29、AI Zn5,5MgCu ide) Class B A B B B A B B B A B A B B B A Alloy Group II - alloys AI Mg with more than 2,8% Mg - alloys AI CuMg - alloys AI ZnMg Page 5 EN 603-3 : 2000 6 Tolerances on dimensions and form 6.1 General The technical conditions for inspection and delivery of wrought forging stock are spec

30、ified in EN 603-1. NOTE These products are normally supplied in the F temper as defined in EN 515. 6.2 Extruded round bar 6.2.1 Diameter Tolerances on diameter shall be as specified in Table 2. Tolerances on diameter can vary dependent on the method of extrusion (direct or indirect) and the type of

31、extrusion die used (single hole or multi hole). With Group II alloys closer tolerances are possible when the indirect method of extrusion is employed using either a single hole or multi hole die at the discretion of the supplier. In diameters up to and including 120 mm, however, the forging requirem

32、ent can demand restricted tolerances combined with a more uniform material structure obtainable only with the use of a single hole die. In such cases the purchaser shall specify this special requirement on the order. Table 2 - Tolerances on diameter Dimensions in millimetres Page 6 EN 603-3 : 2000 D

33、iameter Over Up to and including 1 O0 1 O0 200 200 320 6.2.2 Ovality Tolerances on lengths L L 5 2 O00 2000 5 O00 +5 +7 +I o O O O +7 +9 +I 2 O O O +a +11 Ovality shall be determined by calculating the difference between the maximum and minimum diameters measured at one cross section. O The maximum

34、permissible ovality shall be 50% of the tolerance range specified in Table 2; e.g. for a diameter tolerance of i 0,22 mm, the maximum permissible ovality shall be 0,22 mm. 6.2.3 Length The tolerances on fixed length shall be as specified in Table 3. If fixed lengths are to be supplied, this shall be

35、 stated on the order. O If no fixed or minimum length is specified in the order, round extruded bars may be delivered in random lengths. The actual lengths and tolerances on random lengths shall be agreed between supplier and purchaser. 6.2.4 Perpendicularity of cut ends The maximum deviation from p

36、erpendicularity of cut ends shall be within half of the fixed length tolerance range (see Table 3) for both fixed and random lengths, e.g. for a tolerance on fixed length of +IO mm, the perpendicularity of cut ends shall be within 5 mm. O 6.2.5 Straightness The maximum deviations from straightness,

37、h, and h, shall be as specified in Table 4. They shall be measured as shown in Figure 1 with the bar placed on a horizontal baseplate so that its mass decreases the deviation. These straightness tolerances shall be applied only when requested by the purchaser and stated on the order. Page 7 EN 603-3

38、 : 2000 L 1 - 1 Baseplate 2 Straightedge Figure 1 - Measurement of deviation from straightness Table 4 - Straightness tolerances Dimensions in millimetres 6.3 Extruded square bar 6.3.1 Width across flats The width across fiats tolerances shall be as specified in Table 5. Table 5 - Width across flats

39、 tolerances Dimensions in millimetre Page 8 EN 603-3 : 2000 Specified corner radius mm 55 5 6.3.2 Corner radius Maximum allowable deviation from specified corner radius i 0,50 mm k 10 % 6.3.2.1 When a corner radius is specified by the purchaser, the maximum allowable corner radius shall be as specif

40、ied in Table 6. deviation from the specified 6.3.2.2 When a corner radius is not specified by the purchaser, the sharp edges may be slightly rounded. maximum allowable comer radius shall be as specified in Table 7. Table 7 - Maximum corner radius Dimensions in millimetres 6.3.3 Perpendicularity The

41、maximum deviation from perpendicularity rshall be as specified in Table 8. The deviation from perpendicularity shall be measured as shown in Figure 2. The Figure 2 - Measurement of deviation from perpendicularity Page 9 EN 603-3 : 2000 Width across flats S Over I Uptoand Maximum deviation from perpe

42、ndicularity 10 a 1 O0 180 6.3.4 Convexity - concavity The tolerances for convexity - concavity fshali be as specified in Table 9. Convexity - concavity shall be measured as shown in Figure 3. including Z 1 O0 0,Ol x width 180 1 ,O 220 1,5 f - S I t Figure 3 - Measurement of convexity - concavity Pag

43、e 10 EN 603-3 : 2000 Width across flats S Over Up to and Including 10 a 18 18 25 25 40 40 50 50 65 65 80 Rn I nn Tolerances for Convexity - concavity f 0,15 0,20 0,25 0,30 0,35 0,40 n 5n 1 O0 120 150 180 6.3.5 Straightness Maximum deviations from straightness h, and h, shall be as specified in Table

44、 10. They shall be measured as shown in 6.2.5. 120 0,60 150 0,75 180 0,90 220 1,1 Table 10 - Straightness tolerances Dimensions in millimetres I Width across flats S Over 1 Uptoand I Maximum deviation Maximum localiced from straightness I kink in any 300 mm portion loa 80 120 I a Incliiriinn width a

45、m-r=s flats 10 I Including h, in mm/m h, 80 2,O 0,80 120 2,5 1 ,o 200 3,O 1,s 6.3.6 Twist The twist tolerances Tshall be as specified in Table 11. The measurement of twist shall be carried out as shown in Figure 4. Page 11 EN 603-3 : 2000 Over I Uptoand I per 1 O00 mrn 1 Baseplate Over the Figure 4

46、- Measurement of twist Table 11 - Twist tolerances Dimensions in millimetres 10 a 50 120 30 including of length Total length 30 1 ,O 3,O 120 290 5,O 220 3-0 68 50 13 4,o 6.3.7 Length The tolerances on fixed length shall be as specified in Table 12. If fixed lengths are to be supplied, this shall be

47、stated on the order. Table 12 - Fixed length tolerances Dimensions in millimetres If no fixed or minimum length is specified on the order, square extruded bars may be delivered in random lengths. The actual lengths and tolerances on random lengths shall be agreed between supplier and purchaser. Page

48、 12 EN 603-3 : 2000 6.3.8 Perpendicularity of cut ends The maximum deviation from perpendicularity of cut ends shall be within half of the fixed length tolerance range (see Table 12) for both fixed and random lengths, e.g. for a tolerance on fixed length of +10 rnm, the perpendicularity of cut ends

49、shall be within 5 mm. 6.4 Extruded rectangular bar O 6.4.1 Thickness and width Tolerances on thickness and width shall be in accordance with Table 13 (Alloy Group I) and Table 14 (Alloy Group Il). Page 13 EN 603-3 : 2000 +I +I +I +I +I +I +I +I +I - O Tt Cu VI m V O 4 4 - O VI V O 4 2 - O (u VI m V O Q) 7- - O Q) VI V O m % O ro VI V O m L - O m VI V 00 4 r _ Qi VI V O r 4 7 - 0 VI c. - v) $5 CE 23 SC 00 I- - QU cc OJ lu, au 3 E c- Pj 8 - wmm -Cu I +I +I u2bY +I +I ,;(u- I m*Q)cC +I +I + 7777 rab* +I +I + FYY7 E8-a 0-0 - +I +I