DIN EN 825-2013 Thermal insulating products for building applications - Determination of flatness German version EN 825 2013《建筑用热绝缘产品 平整度的测定 德文版本EN 825-2013》.pdf

1、May 2013 Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91.

2、100.60!%$*“2010758www.din.deDDIN EN 825Thermal insulating products for building applications Determination of flatness;English version EN 825:2013,English translation of DIN EN 825:2013-05Wrmedmmstoffe fr das Bauwesen Bestimmung der Ebenheit;Englische Fassung EN 825:2013,Englische bersetzung von DIN

3、 EN 825:2013-05Produits isolants thermiques destins aux applications du btiment Dtermination de la planit;Version anglaise EN 825:2013,Traduction anglaise de DIN EN 825:2013-05SupersedesDIN EN 825:1994-11www.beuth.deDocument comprises 10 pagesIn case of doubt, the German-language original shall be c

4、onsidered authoritative.04.13 DIN EN 825:2013-05 2 A comma is used as the decimal marker. National foreword This document (EN 825:2013) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products” (Secretariat: DIN, Germany) The responsible German body involved in i

5、ts preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Working Committee NA 005-56-60 AA Wrmedmmstoffe. Amendments This standard differs from DIN EN 825:1994-11 as follows: a) the standard has been editorially revised. Previous editions DIN 18165: 1957-

6、08, 1963-03 DIN 18164: 1963-01, 1966-08 DIN 18164-1: 1972-12, 1979-06, 1991-12, 1992-08 DIN 18165-1: 1975-01, 1987-03, 1991-07 DIN 18161-1: 1976-12 DIN 18174: 1981-01 DIN EN 825: 1994-11 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 825 March 2013 ICS 91.100.60 Supersedes EN 825:1994 English

7、Version Thermal insulating products for building applications Determination of flatness Produits isolants thermiques destins aux applications du btiment Dtermination de la planit Wrmedmmstoffe fr das Bauwesen Bestimmung der Ebenheit This European Standard was approved by CEN on 15 December 2012. CEN

8、 members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on appl

9、ication to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Ma

10、nagement Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lat

11、via, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-10

12、00 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 825:2013: E 2 Contents Page Foreword . 3 1 Scope 5 2 Normative references . 5 3 Terms and definitions 5 4 Principle 5 5 Apparatus . 5 6 Test specimens 5 7 Procedure .

13、 6 8 Calculation and expression of results 7 9 Accuracy of measurement . 7 10 Test report 7 EN 825:2013 (E) DIN EN 825:2013-053 Foreword This document (EN 825:2013) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products”, the secretariat of which is held by DIN

14、. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2013, and conflicting national standards shall be withdrawn at the latest by September 2013. Attention is drawn to the possibility that

15、some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 825:1994. The revision of this standard contains no major changes, only minor corrections and clarifi

16、cations of an editorial nature. This European standard has been drafted for applications in building but it may also be used in other areas where it is relevant. This European test standard is one of the following group of interrelated standards on test methods for determining dimensions and propert

17、ies of thermal insulation materials and products, all of which fall within the scope of CEN/TC 88: EN 822, Thermal insulating products for building applications Determination of length and width EN 823, Thermal insulating products for building applications Determination of thickness EN 824, Thermal

18、insulating products for building applications Determination of squareness EN 825, Thermal insulating products for building applications Determination of flatness EN 826, Thermal insulating products for building applications Determination of compression behaviour EN 1602, Thermal insulating products

19、for building applications Determination of the apparent density EN 1603, Thermal insulating products for building applications Determination of dimensional stability under constant normal laboratory conditions (23 C/50 % relative humidity) EN 1604, Thermal insulating products for building applicatio

20、ns Determination of dimensional stability under specified temperature and humidity conditions EN 1605, Thermal insulating products for building applications Determination of deformation under specified compressive load and temperature conditions EN 1606, Thermal insulating products for building appl

21、ications Determination of compressive creep EN 1607, Thermal insulating products for building applications Determination of tensile strength perpendicular to faces EN 1608, Thermal insulating products for building applications Determination of tensile strength parallel to faces EN 825:2013 (E) DIN E

22、N 825:2013-054 EN 1609, Thermal insulating products for building applications Determination of short-term water absorption by partial immersion EN 12085, Thermal insulating products for building applications Determination of linear dimensions of test specimens EN 12086, Thermal insulating products f

23、or building applications Determination of water vapour transmission properties EN 12087, Thermal insulating products for building applications Determination of long-term water absorption by immersion EN 12088, Thermal insulating products for building applications Determination of long-term water abs

24、orption by diffusion EN 12089, Thermal insulating products for building applications Determination of bending behaviour EN 12090, Thermal insulating products for building applications Determination of shear behaviour EN 12091, Thermal insulating products for building applications Determination of fr

25、eeze-thaw resistance EN 12429, Thermal insulating products for building applications Conditioning to moisture equilibrium under specified temperature and humidity conditions EN 12430, Thermal insulating products for building applications Determination of behaviour under point load EN 12431, Thermal

26、insulating products for building applications Determination of thickness for floating floor insulating products EN 13793, Thermal insulating products for building applications Determination of behaviour under cyclic loading EN 13820, Thermal insulating materials for building applications Determinati

27、on of organic content According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of

28、Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. EN 825:2013 (E) DIN EN 825:2013-055 1 Scope This European Standar

29、d specifies the equipment and procedures for determining the deviation from flatness for full-size products. It is applicable to thermal insulating products. 2 Normative references This European Standard contains no normative references. 3 Terms and definitions For the purposes of this document, the

30、 following term and definition applies. 3.1 deviation from flatness maximum distance between the product placed on a flat surface with the convex side uppermost and the flat surface 4 Principle The maximum distance between the product placed on a flat surface and the flat surface is measured. 5 Appa

31、ratus 5.1 Flat surface. 5.2 Metal rule or metal tape, graduated in millimetres and permitting reading to 0,5 mm. 5.3 Rigid frame with a movable measuring device consisting of a disc with a diameter of 30 mm, fixed to a graduated pin or a dial gauge (graduated to at least 0,5 mm) applying a load of (

32、2,0 0,1) N. Any test equipment which provides the same result with at least the same accuracy may be used. 6 Test specimens 6.1 Dimensions of test specimens The test specimen shall be the full-size product. 6.2 Number of test specimens The number of test specimens shall be as specified in the releva

33、nt product standard. In the absence of a product standard, the number of test specimens may be agreed between parties. 6.3 Conditioning of test specimens The test specimens shall be stored for at least 6 h at (23 5) C. In cases of dispute, they shall be stored at (23 2) C and (50 5) % relative humid

34、ity for the time specified in the relevant product standard. EN 825:2013 (E) DIN EN 825:2013-056 7 Procedure 7.1 Test conditions The test shall be carried out at (23 5) C. In cases of dispute, it shall be carried out at (23 2) C and (50 5) % relative humidity. 7.2 Test procedure 7.2.1 Lay the test s

35、pecimen with the convex face, if any, uppermost on a flat surface. If there is a visible deviation from flatness only along the length or only along the width, make the measurement in accordance with 7.2.2 (see Figures 1a and 1b). If there is a deviation from flatness along both the length and width

36、 (warped products), make the measurement in accordance with 7.2.3 (see Figure 2). 7.2.2 Using the metal tape or rule, measure the maximum distance between the bottom edge of the specimen and the flat surface, Smax, to the nearest 0,5 mm. 7.2.3 Locate the maximum and minimum distances from the flat s

37、urface using the measuring device (see 5.3) as shown in Figure 2. At these positions read the distances Ymaxand Ymin,to the nearest 0,5 mm. If the test specimen only rests on three points, the possibility of alternative flatness measurements exists and all shall be measured. a) Measurement of deviat

38、ion from flatness in length b) Measurement of deviation from flatness in width Figure 1 Measurement of deviation from flatness EN 825:2013 (E) DIN EN 825:2013-057 Figure 2 Location of maximum and minimum distances 8 Calculation and expression of results For test specimens with deviation from flatnes

39、s in one direction only, report the deviation as the maximum value measured in millimetres. For warped products, calculate the deviation from flatness, Smax, in millimetres, using the following formula: Smax= Ymax Ymin (1) 9 Accuracy of measurement NOTE It has not been possible to include a statemen

40、t of the accuracy of the method in this edition of the standard, but it is intended to include such a statement when the standard is next revised. 10 Test report The test report shall include the following information: a) reference to this European Standard; b) product identification: 1) product nam

41、e, factory, manufacturer or supplier; 2) production code number; 3) type of product; 4) packaging; 5) the form in which the product arrived at the laboratory; 6) other information as appropriate, e.g. nominal thickness, nominal density; EN 825:2013 (E) DIN EN 825:2013-058 2) conditioning; 3) deviati

42、on from Clauses 6 and 7, if any; 4) date of test; 5) general information relating to the test; 6) any occurrences which may have affected the results. Information about the apparatus and identity of the technician should be available in the laboratory but it need not be recorded in the report; d) results: all individual values and the maximum value of the deviation from flatness and the position where it occurred. c) test procedure: 1) pre-test history and sampling (e.g. who sampled and place of sampling ); EN 825:2013 (E) DIN EN 825:2013-05