DIN EN 840-4-2013 Mobile waste and recycling containers Part 4 Containers with 4 wheels with a capacity up to 1 700 l with flat lid(s) for wide trunnion or BG- and or wide comb lif.pdf

1、February 2013 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).I

2、CS 13.030.40!$R0“1944713www.din.deDDIN EN 840-4Mobile waste and recycling containers Part 4: Containers with 4 wheels with a capacity up to 1 700 l with flatlid(s), for wide trunnion or BG- and/or wide comb lifting devices Dimensions and design;English version EN 840-4:2012,English translation of DI

3、N EN 840-4:2013-02Fahrbare Abfall- und Wertstoffbehlter Teil 4: Behlter mit 4 Rdern und einem Nennvolumen bis 1 700 l mit Flachdeckel(n), frbreite Schttungen mit Zapfenaufnahme oder BG-Schttungen und/oder fr breiteKammschttungen Mae und Formgebung;Englische Fassung EN 840-4:2012,Englische bersetzung

4、 von DIN EN 840-4:2013-02Conteneurs roulants ordures mnagres et recyclables Partie 4: Conteneurs 4 roues de capacit infrieure ou gale 1 700 l couvercle(s)plat(s), pour lve-conteneurs par tourillon large ou BG-basculeurs et/ou lve-conteneurs peigne large Dimensions et conception;Version anglaise EN 8

5、40-4:2012,Traduction anglaise de DIN EN 840-4:2013-02SupersedesDIN EN 840-4:2004-07www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 20 pages 02.13 DIN EN 840-4:2013-02 2 A comma is used as the decimal marker. National foreword This docum

6、ent (EN 840-4:2012) has been prepared by Technical Committee CEN/TC 183 “Waste management” (Secretariat: DIN, Germany), Working Group WG 1 “Waste containers” (lead-management: UNI, Italy). The responsible German body involved in its preparation was the Normenausschuss Kommunale Technik (Municipal Se

7、rvices Standards Committee), Working Committee NA 051-02-01 AA Abfallentsorgung; Umleer-behlter bis 5 m3und Abfallbehlterschrnke (Spiegelgremium fr CEN/TC 183/WG 1). Amendments This standard differs from DIN EN 840-4:2004-07 as follows: a) the German title has been modified; b) the standard has been

8、 editorially revised and brought in line with the state of the art; c) frontal receivers Form B and Form C have been deleted and Figure 2 has been changed accordingly; d) Figure 3 has been deleted. Previous editions DIN EN 840-4: 1997-03, 2004-07 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN

9、840-4 December 2012 ICS 13.030.40 Supersedes EN 840-4:2004English Version Mobile waste and recycling containers - Part 4: Containers with 4 wheels with a capacity up to 1 700 l with flat lid(s), for wide trunnion or BG- and/or wide comb lifting devices - Dimensions and design Conteneurs roulants ord

10、ures mnagres et recyclables - Partie 4: Conteneurs 4 roues de capacit infrieure ou gale 1 700 l couvercle(s) plat(s), pour lve-conteneurs par tourillon large ou BG-basculeurs et/ou lve-conteneurs peigne large - Dimensions et conception Fahrbare Abfall- und Wertstoffbehlter - Teil 4: Behlter mit 4 Rd

11、ern und einem Nennvolumen bis 1700 l mit Flachdeckel(n), fr breite Schttungen mit Zapfenaufnahme oder BG-Schttungen und/oder fr breite Kammschttungen - Mae und Formgebung This European Standard was approved by CEN on 22 September 2012. CEN members are bound to comply with the CEN/CENELEC Internal Re

12、gulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN me

13、mber. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.

14、 CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Polan

15、d, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form a

16、nd by any means reserved worldwide for CEN national Members. Ref. No. EN 840-4:2012: EEN 840-4:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Volumes 55 Dimensions and design 56 Nominal mass .67 Safety and health requirements .68 Testing 69 Marking .6

17、10 Designation 7Annex A (informative) Recommendations for manufacturers of lifting devices . 15Annex B (informative) A-Deviations . 17Bibliography . 18DIN EN 840-4:2013-02EN 840-4:2012 (E) 3 Foreword This document (EN 840-4:2012) has been prepared by Technical Committee CEN/TC 183 “Waste management”

18、, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at the latest by June 2013. Attention is

19、 drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 840-4:2004. Technical changes since the latest edition: The content wa

20、s adapted to the current state of the art and revised editorially. Figure 3 has been deleted. Frontal receivers Form B and C have been deleted. Figure 2 has been changed accordingly. This European Standard is one part of the series of standards of EN 840 with the main title Mobile waste and recyclin

21、g containers comprising the following parts: Part 1: Containers with 2 wheels with a capacity up to 400 l for comb lifting devices Dimensions and design; Part 2: Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or comb lifting devices Dimensions and design; P

22、art 3: Containers with 4 wheels with a capacity up to 1 300 l with dome lid(s), for trunnion and/or comb lifting devices Dimensions and design; Part 4: Containers with 4 wheels with a capacity up to 1 700 l with flat lid(s), for wide trunnion or BG- and/or wide comb lifting devices Dimensions and de

23、sign (the present document); Part 5: Performance requirements and test methods; Part 6: Safety and health requirements. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium,

24、Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland

25、, Turkey and the United Kingdom. DIN EN 840-4:2013-02EN 840-4:2012 (E) 4 1 Scope This European Standard specifies dimensions and design requirements of mobile waste and recycling containers with 4 wheels, with flat lid(s) and capacity up to 1 700 l to be used by wide trunnion or BG-lifting device an

26、d/or wide comb lifting device. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the reference

27、d document (including any amendments) applies. EN 840-5, Mobile waste and recycling containers Part 5: Performance requirements and test methods EN 840-6:2012, Mobile waste and recycling containers Part 6: Safety and health requirements EN 1501-1, Refuse collection vehicles General requirements and

28、safety requirements Part 1: Rear loaded refuse collection vehicles EN ISO 11469, Plastics Generic identification and marking of plastics products (ISO 11469) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. NOTE Terms for components of mobile wast

29、e and recycling containers and lifting devices in three languages are given in Annex A of EN 840-1:2012. 3.1 mobile waste and recycling container appropriately designed container fitted with wheels intended to temporarily store waste 3.2 lifting device structure which picks-up, tilts and empties con

30、tainers 3.3 comb lifting device lifting device in which the picking-up system consists of a row of teeth and a locking system to retain the container during emptying 3.4 trunnion lifting device lifting device in which the picking-up system consists of a pair of arms with automatic locking mechanism

31、to fit the trunnion to retain the container during emptying 3.5 BG lifting device lifting device in which the picking-up system consists of a pair of arms with adaptors that fit the BG receivers and locks them in order to retain the container during emptying Note 1 to entry: See Figures 5 and 6. DIN

32、 EN 840-4:2013-02EN 840-4:2012 (E) 5 3.6 volume total space inside the container when the lid is closed 3.7 nominal volume capacity volume stated by the manufacturer Note 1 to entry: See Table 1 without tolerances. Note 2 to entry: The English term “capacity“ and the French term “capacit“ are transl

33、ated in the German version by the term “Nennvolumen“. 3.8 nominal mass mass, which is calculated as given in Clause 6 3.9 total permissible mass mass of the container plus the nominal load 3.10 functional and safety dimensions essential dimensions which ensure the functionality and interchangeabilit

34、y of the container with the compatible lifting device and which are necessary for the operators safety and health 4 Volumes This part of EN 840 identifies the two classes of containers: Class I - small size (nominal volume up to 1 050 l); Class II - large size (nominal volume between 1 050 l and 1 7

35、00 l). Within the two above-mentioned classes of containers the following volumes are identified: 750 l, 1 000 l, 1 300 l, 1 400 l, 1 500 l, 1 600 l and 1 700 l. Nominal volumes different from those referenced can be used by agreement between user and manufacturer. The tolerance of the volumes shall

36、 be 5 % maximum measured according to EN 840-5. 5 Dimensions and design 5.1 The design of the containers do not need to correspond to the drawings given in Figure 1. The functional dimensions given in Table 1 shall be respected. Recommendations for manufacturers of lifting devices are given in Annex

37、 A (see also EN 1501-1). 5.2 The container shall be constructed so that when it is unloaded or loaded with a nominal load (see Clause 6), it fits on an approved compatible lifting device. It shall be automatically locked safely into the lifting device during the lifting operation. If the container i

38、s equipped with a comb receiver, it shall correspond to Figure 2. 5.3 The lid(s) shall cover the opening of the container completely. It shall be opened easily by itself during the emptying cycle It/they shall be made with at least two fixing points and have at least one means of opening. DIN EN 840

39、-4:2013-02EN 840-4:2012 (E) 6 5.4 Handles fitted in front of the trunnion shall have a measurement over the handles of 10 mm less than the actual measurement in Table 1, dimension N 33. The handles and their location also shall be designed so that they do not damage the operator. 5.5 If the containe

40、r has ribs in the frontal receiver they shall meet the requirements of Figure 4. 5.6 The container shall have four swivel castors. Each swivel castor shall be capable of withstanding 1/3 of the total permissible mass. Each castor shall meet the requirements of EN 840-5. The container shall have faci

41、lities for mounting the castor platine according to at least one of the measurements as shown in Figure 7. 5.7 All the surfaces of the container including design features shall be smooth and free of any foreign bodies or flaws. 5.8 The container should have a drain plug. 5.9 When direction locks are

42、 fitted they shall be fixed on at least 2 castors. 5.10 The container should be fitted with 2 braked wheels to requirements of EN 840-5. In case of centralised braking and locking system the brake pedal and the lock shall be fixed on a lateral side of the container. The centralised locking shall be

43、able to be unlocked with a standard triangular key as shown in Figure 8. The effectiveness of this centralised braking system shall conform to EN 840-5. 6 Nominal mass The container shall be constructed strongly enough to carry a mass of 0,4 kg/dm x nominal volume. Containers with a nominal volume o

44、f more than 1 100 l shall be constructed strongly enough to carry a load of 440 kg. 7 Safety and health requirements The container shall meet the safety and health requirements according to EN 840-6. 8 Testing The container shall fulfil the performance requirements and the tests of EN 840-5. 9 Marki

45、ng 9.1 Each container complying with the requirements of this part of EN 840 shall be durably and readably marked on the body in a visible part with: number of this European Standard (EN 840-4); nominal volume; manufacturers name or trademark; total permissible mass, in kilograms; year and month of

46、manufacturing. DIN EN 840-4:2013-02EN 840-4:2012 (E) 7 9.2 Additional marking for quality, recycling, etc. is allowed. Starting five years after the publication of this standard, plastic parts of containers, lids and wheels shall be marked in accordance with EN ISO 11469. The use of recycled materia

47、ls is allowed, presuming that all requirements of this standard are complied with. 10 Designation The container complying with the requirements of this European Standard shall be designated as follows: Container EN 840-4 1 700 A A 440 Description Standard number Nominal volume, in litres Frontal rec

48、eiver form: A =frontal receiver 0 = without frontal receiver Lateral receiver: A = trunnions B =BG receiver 0 = without lateral receiver Nominal load, in kilograms DIN EN 840-4:2013-02EN 840-4:2012 (E) 8 Table 1 Dimensions Dimensions in millimetres Dimen-sion N Class I - Small sizes 1 050 l Class II - Lar