DIN EN 934-5-2008 Admixtures for concrete mortar and grout - Part 5 Admixtures for sprayed concrete - Definitions requirements conformity marking and labelling English version of D.pdf

1、February 2008DEUTSCHE NORM English price group 13No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91.100.10; 91.100.30!

2、L+4“1410817www.din.deDDIN EN 934-5Admixtures for concrete, mortar and grout Part 5: Admixtures for sprayed concrete Definitions, requirements, conformity, marking and labellingEnglish version of DIN EN 934-5:2008-02Zusatzmittel fr Beton, Mrtel und Einpressmrtel Teil 5: Zusatzmittel fr Spritzbeton B

3、egriffe, Anforderungen, Konformitt, Kennzeichnung und BeschriftungEnglische Fassung DIN EN 934-5:2008-02See start of validitywww.beuth.deDocument comprises 24 pages-DIN EN 934-5:2008-02 2 Start of validity This standard is due to be valid from 1 July 2008. It should be noted that, in Germany, CE con

4、formity marking of construction products will be permitted once this standard has been listed in the Bundesanzeiger (German Federal Law Gazette) and from the date given therein. National foreword This standard has been prepared by Technical Committee CEN/TC 104 “Concrete and related products” (Secre

5、tariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Technical Committee NA 005-07-02 AA Betontechnik, Subcommittee NA 005-07-23 AA Zusatzmittel fr Beton, Mrtel und Einpressmrtel. EUROPEA

6、N STANDARDNORME EUROPENNEEUROPISCHE NORMEN 934-5October 2007ICS 91.100.10English VersionAdmixtures for concrete, mortar and grout - Part 5: Admixturesfor sprayed concrete - Definitions, requirements, conformity,marking and labellingAdjuvants pour btons projets - Dfinitions, exigences,conformit, marq

7、uage et tiquetageZusatzmittel fr Beton, Mrtel und Einpressmrtel - Teil 5:Zusatzmittel fr Spritzbeton - Begriffe, Anforderungen,Konformitt, Kennzeichnung und BeschriftungThis European Standard was approved by CEN on 13 August 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulati

8、ons which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This Europe

9、an Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the nationa

10、l standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and Unite

11、d Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 934-5:2007: EAdju

12、vants pour bton, mortier et coulis - Partie 5:-EN 934-5:2007 (E) 2 Contents Page Foreword3 1 Scope 5 2 Normative references 5 3 Terms and definitions .6 3.1 General definitions 6 3.2 Specific definitions6 4 Requirements.7 4.1 General requirements7 4.2 Specific requirements .7 5 Sampling.10 6 Conform

13、ity control.10 7 Evaluation of conformity.11 8 Marking and labelling 11 8.1 General11 8.2 Designation of admixtures11 8.3 Additional information 11 Annex A (informative) Content and release of dangerous substances.12 Annex B (normative) Reference concrete for testing consistence control admixture 13

14、 B.1 General13 B.2 Cement content13 B.3 Aggregates .13 B.4 Consistence13 B.5 Compressive strength.14 B.6 Test report 14 Annex C (normative) Measurement of tensile bond strength.15 C.1 General15 C.2 Preparation of the control and test mix.15 C.3 Applying the concrete and storage of specimens .15 C.4

15、Testing 16 C.5 Test report 16 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive17 ZA.1 Scope and relevant characteristics .17 ZA.2 Procedure for attestation of conformity of admixtures for sprayed concrete.19 ZA.2.1 System of

16、 attestation of conformity 19 ZA.2.2 EC certificate and declaration of conformity 20 ZA.3 CE marking and labelling20 Bibliography 22 DIN EN 934-5:2008-02 - EN 934-5:2007 (E) 3 Foreword This document (EN 934-5:2007) has been prepared by Technical Committee CEN/TC 104 “Concrete and related products”,

17、the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2008, and conflicting national standards shall be withdrawn at the latest by July 2009. Attention is

18、drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the Eur

19、opean Free Trade Association, and supports essential requirements of EC Directive(s). For relationship with EC Directive(s), see informative Annex ZA, which is an integral part of this document. This European Standard is a part of the series EN 934 Admixtures for concrete, mortar and grout which is

20、comprised of the following parts: Part 1: Common requirements1)Part 2: Concrete admixtures Definitions, requirements, conformity, marking and labelling Part 3: Admixtures for masonry mortar Definitions, requirements, conformity, marking and labelling Part 4: Admixtures for grout for prestressing ten

21、dons Definitions, requirements, conformity, marking and labelling Part 5: Admixtures for sprayed concrete Definitions, requirements, conformity, marking and labelling Part 6: Sampling, conformity control and evaluation of conformity. This European Standard is used with the standards of the series EN

22、 480 which comprises test methods for admixtures. Subject to the provisions in EN 14487-1, Sprayed concrete Part 1: Definitions, specifications and conformity admixtures covered by EN 934-2 may also be considered for the use in sprayed concrete. A previous draft of EN 934-5 had been submitted to For

23、mal Vote in 2004 and had formally passed the vote by majority of CEN-members in 2005. Together with this vote, however, some members presented severe technical comments which were agreed upon by the relevant CEN/TC 104/SC 3 to be taken into account by an amendment. In order to avoid the need of usin

24、g two separate papers in practice, CEN/TC 104 decided, however, not to publish the agreed document but to submit a further consolidated version including the amended issues to UAP, which finally should be published. The amendments to the final draft prEN 934-5:2004-11 are the following: - Table 1: r

25、equirements in line 5 (Conventional dry material content), 7 (Total chlorine) and 8 (Water soluble chloride); - Table 2: heading of table; curing conditions in footnote d; 1) This document is under preparation. DIN EN 934-5:2008-02 - EN 934-5:2007 (E) 4 - Table 3: heading of table; - Table 4: headin

26、g of table; - Table 5: minimum frequency of testing of alkali content; - Annex B: new clauses B.4 and B.5 with more details of testing; new clause B.6, extending the test report; - Annex C: detailing the testing in clause C.4. According to the CEN/CENELEC Internal Regulations, the national standards

27、 organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portug

28、al, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 934-5:2008-02 EN 934-5:2007 (E) 5 1 Scope This European Standard defines and specifies requirements and conformity for admixtures specifically intended for use in sprayed concrete. The types of admixtures cove

29、red are: set accelerating and non-alkaline set accelerating admixtures; consistence control admixtures; bond improving admixtures. Provisions governing the practical application of these admixtures in the production of sprayed concrete are not part of this European Standard. 2 Normative references T

30、he following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 196-1, Methods of testing cement Part 1: Determ

31、ination of strength EN 196-3, Methods of testing cement Part 3: Determination of setting times and soundness EN 197-1, Cement Part 1: Composition, specifications and conformity criteria for common cements EN 480-1, Admixtures for concrete, mortar and grout Test methods Part 1: Reference concrete and

32、 reference mortar for testing EN 480-2, Admixtures for concrete, mortar and grout Test methods Part 2: Determination of setting time EN 480-6, Admixtures for concrete, mortar and grout Test methods Part 6: Infrared analysis EN 480-8, Admixtures for concrete, mortar and grout Test methods Part 8: Det

33、ermination of the conventional dry material content EN 480-10, Admixtures for concrete, mortar and grout Test methods Part 10: Determination of water soluble chloride content EN 480-12, Admixtures for concrete, mortar and grout Test methods Part 12: Determination of the alkali content of admixtures

34、EN 934-6:2001, Admixtures for concrete, mortar and grout Part 6: Sampling, conformity control and evaluation of conformity EN 1542:1999, Products and systems for the protection and repair of concrete structures Test methods Measurement of bond strength by pull-off EN 12350-2, Testing fresh concrete

35、Part 2: Slump test EN 12350-5, Testing fresh concrete Part 5: Flow table test EN 12390-3, Testing hardened concrete Part 3: Compressive strength of test specimens DIN EN 934-5:2008-02 -EN 934-5:2007 (E) 6 EN ISO 1158, Plastics Vinyl chloride homopolymers and copolymers Determination of chlorine cont

36、ent (ISO 1158:1998) ISO 758, Liquid chemical products for industrial use Determination of density at 20 degrees C ISO 4316, Surface active agents Determination of pH of aqueous solutions Potentiometric method 3 Terms and definitions For the purposes of this European Standard, the following terms and

37、 definitions apply. 3.1 General definitions 3.1.1 performance ability of an admixture to be effective in its intended use without detrimental effects 3.1.2 compliance dosage dosage of an admixture, expressed in % by mass of cement, stated by the manufacturer, which will meet the requirements of this

38、 European Standard NOTE The compliance dosage should be within the recommended range of dosage. 3.1.3 recommended range of dosage dosages between limits expressed in % by mass of cement that the manufacturer recommends for the product based on experience on site NOTE The use of the recommended dosag

39、e does not imply that compliance with this European Standard will be met over the whole range. Trial tests should be carried out with the materials to be used on site to find the dosage necessary to achieve the required result. 3.1.4 maximum recommended dosage upper limit of the recommended range of

40、 dosage 3.1.5 control mix prescribed mix without admixture 3.1.6 test mix prescribed mix incorporating an admixture 3.2 Specific definitions 3.2.1 sprayed concrete admixture material added to the concrete mix before or during the spraying process, in a quantity not exceeding 5 % by mass of cement, e

41、xcept for sprayed concrete set accelerating admixture, where the dosage should not exceed 12 %, to modify the properties of the mix in the fresh and/or hardened state 3.2.2 sprayed concrete set accelerating admixture admixture to develop very early setting of the sprayed concrete differing from set

42、accelerating admixtures as defined and specified in EN 934-2 DIN EN 934-5:2008-02 EN 934-5:2007 (E) 7 3.2.3 non-alkaline sprayed concrete set accelerating admixture sprayed concrete set accelerating admixture according to 3.2.2 with an alkali content (given as Na2O-equivalent) not exceeding 1,0 % by

43、 mass of the admixture 3.2.4 consistence control admixture admixture that retains consistency for a long period NOTE This type of admixture is normally used in combination with a compatible sprayed concrete set accelerating admixture. 3.2.5 bond improving admixture admixture added to the concrete mi

44、x before or during the process of spraying and which improves the bond between the sprayed concrete layers and/or the substrate surface 4 Requirements 4.1 General requirements All the admixtures defined in this European Standard shall conform to the general requirements given in Table 1. NOTE For re

45、quirements that lead to the CE-marking, see Table ZA.1. 4.2 Specific requirements Additional to the general requirements in 4.1, the admixtures defined in 3.2.1 to 3.2.5 shall conform to the following specific requirements: Sprayed concrete set accelerating admixture Table 2 Non-alkaline sprayed con

46、crete set accelerating admixture Table 2 Consistence control admixture Table 3 Bond improving admixture Table 4 These requirements shall be satisfied within the recommended range of dosage. DIN EN 934-5:2008-02 -EN 934-5:2007 (E) 8 Table 1 General requirements iProperty Test method Requirements 1 Ho

47、mogeneity aVisual Homogeneous when used. Segregation shall not exceed the limit stated by the manufacturer. 2 ColouraVisual Uniform and similar to the description declared by the manufacturer. 3 Effective component aEN 480-6 bInfrared spectra to show no significant change with respect to the effecti

48、ve component when compared to reference spectrum provided by the manufacturer. 4 Relative density aISO 758 D 0,03 if D 1,10 D 0,02 if D 1,10 Where D is the manufacturers stated value of density. 5 Conventional dry material content aEN 480-8 c0,95 T X 1,05 T, if T 20 % 0,90 T X 1,10 T, if T 20 % T is

49、 manufacturers stated value % m/m.; X is test result % by mass on dry material content. 6 pH-Value a(only for liquid admixtures) ISO 4316 Manufacturers stated value 1 or within manufacturers stated range. 7 Total chlorine a dEN ISO 1158 eEither 0,10 % by mass or not above the manufacturers stated range. 8 Water soluble chloride aEN 480-10 Either 0,10 % by masshor not above the manufacturers stated range. 9 Alkali content (Na2O-equivalent) aEN 480-12 Not above the ma