1、October 2011 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC
2、S 97.140!$t“1819395www.din.deDDIN EN 16014Hardware for furniture Strength and durability of locking mechanismsEnglish translation of DIN EN 16014:2011-10Mbelbeschlge Festigkeit und Dauerhaltbarkeit von VerschlussmechanismenEnglische bersetzung von DIN EN 16014:2011-10Quincaillerie dameublement Rsist
3、ance mcanique et endurance des mcanismes de verrouillageTraduction anglaise de DIN EN 16014:2011-10SupersedesDIN 68852:2004-06www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.09.1124DIN EN 16014:2011-10 A comma is used as the decima
4、l marker. National foreword This standard has been prepared by Technical Committee CEN/TC 207 “Furniture”, (Secretariat:UNI, Italy). The responsible German body involved in its preparation was the Normenausschuss Holzwirtschaft und Mbel (Timber and Furniture Standards Committee), Working Committee N
5、A 042-05-06 AA SpA zu CEN/TC 207/WG 8 Anforderungen und Prfverfahren fr Mbelbeschlge. Amendments This standard differs from DIN 68852:2004-06 as follows: a) the DIN Standard has been changed to a European Standard; b) types and designations have been deleted; c) Annex A “Product information system”
6、has been added; d) Annex B “Test parameters” has been added; e) the standard has been editorially revised. Previous editions DIN 68852: 1981-07, 2004-06 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16014 August 2011 ICS 97.140 English Version Hardware for furniture - Strength and durabilit
7、y of locking mechanisms Quincaillerie dameublement - Rsistance mcanique et endurance des mcanismes de verrouillage Mbelbeschlge - Festigkeit und Dauerhaltbarkeit von Verschlussmechanismen This European Standard was approved by CEN on 1 July 2011. CEN members are bound to comply with the CEN/CENELEC
8、Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to
9、 any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the officia
10、l versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak
11、ia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide f
12、or CEN national Members. Ref. No. EN 16014:2011: EEN 16014:2011 (E) 2 Contents Page Foreword 3Introduction .31 Scope 42 Normative references 43 Terms and definitions .44 General test conditions .54.1 Preliminary preparation 54.2 Test equipment 54.3 Application of forces .54.4 Tolerances (allowed var
13、iation from the nominal values).64.5 Test sequence 64.6 Inspection and assessment of results 65 Test apparatus .65.1 Loading pad 65.2 Test plates 75.3 Particle board properties 76 Test procedure and requirements 76.1 General 76.2 Overload tests 76.2.1 General 76.2.2 Lock .76.2.3 Bolt 86.2.4 Shooting
14、 bar .96.2.5 Locking hook . 106.3 Functional tests 116.3.1 General . 116.3.2 Locks 126.3.3 Bolt . 126.3.4 Shooting bar 136.3.5 Locking hook . 146.3.6 Torque test 156.4 Durability tests 166.4.1 Locks 166.4.2 Cylinder and key . 186.5 Corrosion resistance 187 Test report . 19Annex A (informative) Produ
15、ct information system . 20A.1 General . 20A.2 Field of application . 20A.3 Corrosion resistance 20Annex B (normative) Test parameters . 21Bibliography . 22DIN EN 16014:2011-10 EN 16014:2011 (E) 3 Foreword This document (EN 16014:2011) has been prepared by Technical Committee CEN/TC 207 “Furniture”,
16、the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2012, and conflicting national standards shall be withdrawn at the latest by February 2012. Attent
17、ion is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of t
18、he following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romani
19、a, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Introduction The aim of this European Standard is to provide furniture manufacturers, designers and developers with comparable information regarding the performance of all types of locking mechanisms. NOTE Examples of typical
20、locking mechanisms are given in CEN/TR 16015. DIN EN 16014:2011-10 EN 16014:2011 (E) 4 1 Scope This European Standard specifies test methods and requirements for the strength and durability of all types of locking mechanisms for furniture and their components for all fields of application. This Euro
21、pean Standard does not apply to latching mechanisms. The tests consist of the application of loads, forces simulating normal functional use, as well as misuse that might reasonably be expected to occur. With the exception of the corrosion test in 6.5, the tests are designed to evaluate properties wi
22、thout regard to materials, design/construction or manufacturing processes. The strength and durability tests only relate to the locking mechanisms and their components and the parts used for the attachment, e.g. screws. The strength and durability tests are carried out in particle board with specifi
23、ed properties. The test results can only be used as a guide to the performance of a piece of furniture. The test results are only valid for the locking mechanisms and their components tested. These results may be used to represent the performance of production models provided that the tested model i
24、s representative of the production model. With the exception of corrosion, ageing and influences of heat and humidity is not included. Annex A (normative): Product information system. Annex B (normative): Test parameters. 2 Normative references The following referenced documents are indispensable fo
25、r the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 320:2011, Particleboards and fibreboards - Determination of resistance to axial withdrawal of screws
26、EN 323:1993, Wood-based panels Determination of density EN ISO 6270-2:2005, Paints and varnishes Determination of resistance to humidity Part 2: Procedure for exposing test specimens in condensation-water atmospheres (ISO 6270-2:2005) 3 Terms and definitions For the purposes of this document, the fo
27、llowing terms and definitions. 3.1 locking mechanism mechanism that limits access to the interior of a unit or a storage element NOTE It requires a key or a combination in order to activate it or to make it possible to activate it. ISO 7170:2005 and EN 14074:2004 DIN EN 16014:2011-10 EN 16014:2011 (
28、E) 5 3.2 latch mechanism which retains an extension element or a door in the closed position NOTE It requires a second action in order to release it. 3.3 stop part of hardware in the cabinet which works together with the locking hook CEN/TR 16015:2010, 2.5.1 4 General test conditions 4.1 Preliminary
29、 preparation The locking mechanism shall be assembled/mounted according to the instructions supplied with it. If mounting or assembly instructions are not supplied, the most adverse configuration shall be used and the mounting or assembly method shall be recorded in the test report. Fittings shall b
30、e tightened before testing and shall not be re-tightened unless specifically required in the manufacturers instructions. If the configuration must be changed to produce the worst-case conditions, this shall be recorded in the test report. For testing a range of related locks, only worst case(s) need
31、 to be tested. The tests shall be carried out in indoor ambient conditions at a temperature between 15 C and 25 C. If during a test the temperature is outside of the range of 15 C to 25 C, the maximum and/or minimum temperature shall be recorded in the test report. Locking mechanisms which include s
32、tructural hardware parts made of hygroscopic plastic materials, e.g. polyamide shall be conditioned at (23 5) C and a relative humidity of (50 5) % for at least 7 days before testing. If a test cannot be carried out as specified in this standard, e.g. because a loading pad cannot be used for the app
33、lication of a force due to the design of a product, the test shall be carried out as far as possible as specified. Before beginning the testing, visually inspect the lock thoroughly. Record any defects so that they are not assumed to have been caused by the tests. Carry out measurements when specifi
34、ed. 4.2 Test equipment The equipment shall not inhibit deformation of the lock, i.e. it shall be able to move so that it can follow the deformation of the lock during testing. All loading pads shall be capable of pivoting in relation to the direction of the applied force. The pivot point shall be as
35、 close as practically possible to the load surface. 4.3 Application of forces The forces in the static load tests shall be applied sufficiently slowly to ensure that negligible dynamic force is applied. Unless otherwise specified, each force shall be maintained for not less than 10 s and not more th
36、an 15 s. The forces in durability tests shall be applied at a rate to ensure that excessive heating does not occur. DIN EN 16014:2011-10 The forces may be replaced by masses. The relation 10 N = 1 kg shall be used for this purpose. EN 16014:2011 (E) 6 The forces may be replaced by masses. The relati
37、on 10 N = 1 kg shall be used for this purpose. 4.4 Tolerances (allowed variation from the nominal values) Unless otherwise stated, the following tolerances are applicable to the test equipment: Forces: 5 % of the nominal force; Velocities: 5 % of the nominal velocity; Masses: 1 % of the nominal mass
38、; Dimensions: 1 mm of the nominal dimension; Angles: 2 of the nominal angle. NOTE For the purposes of uncertainty measurement, test results are not considered to be adversely affected when the above tolerances are met. 4.5 Test sequence The tests shall be carried out in the same sequence as the clau
39、ses are numbered in this standard. If the clause sequence is not followed, the sequence shall be recorded in the test report. 4.6 Inspection and assessment of results Before and after completion of each test, carry out the inspection as specified, after using adjustment devices, if available. Record
40、 any changes that have taken place since the initial inspection. The inspection shall include at least the following: a) the fracture of any component or joint; b) the loosening of any joint intended to be rigid, which can be demonstrated by hand pressure; c) the deformation or wear of any part or c
41、omponent such that its functioning is impaired; d) the loosening of any means of fixing components; e) any impairment of a component or part. 5 Test apparatus 5.1 Loading pad Type A: rigid cylinder with a flat face; the diameter of which shall be 2/3 of the smallest width or diameter of the lock tes
42、ted; Type B: rigid cylinder, (5,0 0,1) mm diameter, with a hemispherical face; Type C: test bolt identical in shape and form to the part belonging to the locking mechanism. DIN EN 16014:2011-10 EN 16014:2011 (E) 7 5.2 Test plates The tests specified in 6.2 and 6.3 shall be carried out in a test plat
43、e, which is so constructed that the deformation at the measurement points under the applied load is no more than 1 mm. The test plate shall be at least 50 mm larger than the lock to be tested. Unless otherwise specified by the manufacturer, the locks shall be mounted on a 19 mm particle board, see 5
44、.3. 5.3 Particle board properties The properties of the particle board shall be as specified in Table 1. Table 1 Particle board properties Property Reference standard Requirement Axis withdrawal of screws EN 320 1 100 N 100 N Density EN 323 0,65 g/cm 0,05 g/cm 6 Test procedure and requirements 6.1 G
45、eneral For the following tests, five sets of locking mechanisms shall be used as follows: the first set shall be used for the tests specified in 6.2; the second set shall be used for the tests specified in 6.3; the third set shall be used for the test specified in 6.4.1; the fourth set shall be used
46、 for the test specified in 6.4.2; the fifth set shall be used for the test specified in 6.5. 6.2 Overload tests 6.2.1 General All locking mechanism shall be tested according to all relevant sub-clauses. The load shall be applied perpendicular to the face of the test plate. 6.2.2 Lock The overload te
47、st shall be carried out as shown in Figure 1 using loading pad A (see 5.1) with the static force F1and the cycles specified in Table B.1. The force shall be applied in the opposite direction of the fixing of the lock. Carry out inspection and assessment according to 4.6 without the test load. The lo
48、cking mechanism or parts of it shall not become detached. DIN EN 16014:2011-10 EN 16014:2011 (E) 8 Dimensions in mm Key 1 reference particle board 2 lock 3 fixing 4 loading pad 5 test plate F1force in N Figure 1 Example for an overload test of a lock 6.2.3 Bolt The overload test shall be carried out
49、 in the locked position as shown in Figure 2 using loading pad B (see 5.1) with the static force F1and the cycles specified in Table B.1. The force shall be applied in the centre of area of the bolt. Carry out inspection and assessment according to 4.6 without the test load. The locking mechanism or parts of it shall not become detached. DIN EN 16014:2011-10 EN 16014:2011 (E) 9 Dimensions in mm Key 1 ref
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1