DIN EN 16065-2012 Packaging - Rigid plastic containers - PET finish 30 25 Low (16 8) German version EN 16065 2011《包装 硬质塑料容器 聚酯修饰30 25低(16 8) 德文版本EN 16065-2011》.pdf

1、February 2012 Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 55.100!$ya$“1866201www.din.deDDIN EN 16065Packaging Rigid plastic containers PET finish 30/25 Low (16,8)English translation of DIN EN 16065:2012-02Verpackung Kunststoffbehltnisse PET-Verschlussmundstck 30/25 flach (16,8)Englische bersetzung von DIN EN 16065:2012-02Emballage Rcipients en plastique

3、rigide Bague PET 30/25 Basse (16,8)Traduction anglaise de DIN EN 16065:2012-02www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.901.12 DIN EN 16065:2012-02 2 A comma is used as the decimal marker. National foreword This standard has

4、been prepared by Technical Committee CEN/TC 261 “Packaging” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Verpackungswesen (Packaging Standards Committee), Working Committee NA 115-02-09 AA Behltnisse aus Kunststoff. EUROPEAN STANDARD N

5、ORME EUROPENNE EUROPISCHE NORM EN 16065 November 2011 ICS 55.100 English Version Packaging - Rigid plastic containers -(16,8) Emballage - Rcipients en plastique rigide -30/25 Basse (16,8) Verpackung - Kunststoffbehltnisse -Verschlussmundstck 30/25 flach (16,8) This European Standard was approved by

6、CEN on 29 October 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standa

7、rds may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and not

8、ified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuan

9、ia, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN

10、 All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16065:2011: EPET finish 30/25 Low Bague PET PET-EN 16065:2011 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Dimensions .53 Requirements .5Bibliography 7DIN EN 16065:2012-02 EN

11、16065:2011 (E) 3 Foreword This document (EN 16065:2011) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, a

12、t the latest by May 2012, and conflicting national standards shall be withdrawn at the latest by May 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all

13、 such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hung

14、ary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 16065:2012-02 EN 16065:2011 (E) 4 Introduction This European Standard is based on CE.T.I.E. (International

15、 Technical Centre for Bottling and Packaging) data sheet GME 30.22 (2007) 1. Efficient packaging is of great importance for the distribution and the protection of goods. Insufficient or inappropriate packaging can lead to damage or wastage of the contents of the pack. DIN EN 16065:2012-02 EN 16065:2

16、011 (E) 5 1 Scope This European Standard specifies the dimensions and requirements of the 30 mm low screw finish with three (3) thread starts for flat waters and non-carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. The dimension (16,8) is t

17、he height in millimetres from the top of finish to the bottom of the support ledge. This finish is designed to take a tamper evident plastic closure only. During first opening, the tamper evident band will separate from the closure shell and stay on a one way bottle neck or like bottles in the retur

18、nable market, the tamper evident band will tear but will remain connected to the closure shell. 2 Dimensions 2.1 The design and dimensions of the finish shall be as shown in Figure 1. 2.2 Dimensions of the 3 thread starts 120 apart. 180 of full depth thread per lead R 6,25 thread lead-in R 6,25 thre

19、ad run-out Lead: 9 mm (travel per turn) 2.3 General tolerance for others radii: 0,13 mm. 2.4 Weight on height 16,8 mm: 3,73 g (density = 1,335). 3 Requirements The following requirements apply. This finish is a top, side and inside seal finish. This finish shall be smooth and free of any defects tha

20、t will contribute to leaks. Flash shall not exceed 0,13 mm per side, and shall not be continuous. On the blown bottle, the control diameter C shall be free of any defects up to 4 mm down for the internal bore and across the sealing surface of the finish. Requirements for good closure application on

21、finish: 0,13 mm max. out-of-parallel sealing surface with neck support ledge is allowed; an offset or vertical mismatch of thread is not to exceed 0,10 mm at the mould seam. T dimension is not measured in the depressed area. Variations in E are to follow uniformly those of T. No overhang allowed at

22、any point in 360 between F and G. A flash to 0,15 mm maximum step is allowable on one side only. G does not exceed E. DIN EN 16065:2012-02 EN 16065:2011 (E) 6 Dimensions in millimetres Key 1 start thread 5 above parting line 2 below parting line 6 thread lead-in 3 thread starts 120 apart 7 thread ru

23、n-out 4 straight NOTE * = includes ovality. Figure 1 Design and dimensions of the finish DIN EN 16065:2012-02 EN 16065:2011 (E) 7 Bibliography 1 CE.T.I.E. data sheet GME 30.22 PET finish 30/25 L (16,8) C.E.T.I.E. : International Technical Centre for Bottling and related Packaging 112 114 rue La Botie 75008 Paris www.cetie.org DIN EN 16065:2012-02