DIN EN 16083-2012 Paddles and oars for recreational boats - Safety requirements and test methods German version EN 16083 2012《游艇的船桨和桨 安全要求和试验方法 德文版本 EN 16083-2012》.pdf

1、March 2012 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 4

2、7.080!$zV$“1875101www.din.deDDIN EN 16083Paddles and oars for recreational boats Safety requirements and test methodsEnglish translation of DIN EN 16083:2012-03Paddel und Ruder/Riemen fr Freizeitboote Sicherheitstechnische Anforderungen und PrfverfahrenEnglische bersetzung von DIN EN 16083:2012-03Pa

3、gaies et rames pour bateaux de loisirs Exigences de scurit et mthodes d essaisTraduction anglaise de DIN EN 16083:2012-03SupersedesDIN 32929:2005-04www.beuth.deDocument comprises 12 pagesIn case of doubt, the German-language original shall be considered authoritative.03.12 DIN EN 16083:2012-04 2 A c

4、omma is used as the decimal marker. Start of validity This standard takes effect on 1 March 2012. National foreword This standard includes safety requirements within the meaning of the Produktsicherheitsgesetz (ProdSG) (German Product Safety Act). This standard has been prepared by Technical Committ

5、ee CEN/TC 136 “Sports, playground and other recreational facilities and equipment”, Working Group WG 13 “Floating leisure articles for use on and in water” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Sport- und Freizeitgert (Sports Equ

6、ipment Standards Committee), Working Committee NA 112-05-09 AA Aufblasbare schwimmende Freizeitgerte einschlielich aufblasbarer Boote und Zubehr. Where this standard has been identified by the Ausschuss fr Produktsicherheit (German Committee for Product Safety) and reference to it has been published

7、 in the Gemeinsames Ministerialblatt (German Joint Ministerial Gazette) by the Bundesanstalt fr Arbeitsschutz und Arbeitsmedizin (BAuA) (German Federal Institute for Occupational Safety and Health), it is to be presumed that paddles and oars for recreational boats which comply with this standard ful

8、fil the relevant health and safety requirements. Where they comply with the provisions laid down in Section 5 of the Product Safety Act, such products may then be marked with the GS mark (German “safety tested” mark) as awarded to the manufacturer by an authorized “GS organization”. Amendments This

9、standard differs from DIN 32929:2005-04 as follows: a) the standard has been adopted as a European Standard; b) the content has been editorially revised; c) the scope of the standard has been revised; d) the tolerance for the test temperature has been modified; e) specifications for materials (forme

10、rly in Subclause 5.3) are no longer included; f) specifications for paddle and oar grips (formerly in Subclause 5.8) are no longer included. Previous editions DIN 32929: 1987-03, 2005-04 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16083 January 2012 ICS 47.080 English Version Paddles and oa

11、rs for recreational boats - Safety requirements and test methods Pagaies et rames pour bateaux de loisirs - Exigences de scurit et mthodes dessais Paddel und Ruder/Riemen fr Freizeitboote - Sicherheitstechnische Anforderungen und Prfverfahren This European Standard was approved by CEN on 29 October

12、2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtaine

13、d on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-C

14、ENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Ma

15、lta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All right

16、s of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16083:2012: EEN 16083:2012 (E) 2 ContentsPage Foreword 31 Scope 42 Terms and definitions .43 Classes and types43.1 Classes .43.2 Types .44 Safety requirements and testing 64.1 General 64.2 Tempera

17、ture .64.3 Bending strength of paddles and oars 64.4 Resistance against buckling of oars and paddles .94.5 Combined parts, couplings 94.6 Floatability . 105 Marking and labelling . 10DIN EN 16083:2012-04EN 16083:2012 (E) 3 Foreword This document (EN 16083:2012) has been prepared by Technical Committ

18、ee CEN/TC 136 “Sports, playground and other recreational facilities and equipment”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2012, and conflict

19、ing national standards shall be withdrawn at the latest by July 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the

20、 CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

21、 Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. DIN EN 16083:2012-04EN 16083:2012 (E) 4 1 Scope This European Standard specifies safety requirements and test methods for paddles and oars for non

22、-rigid hull water crafts. Paddles and oars are classified in two performance levels A and B. This standard is not applicable for paddles and oars for: training and competitive sports; white water; items covered by EN 71-1; folding/rigid framed boats/kayaks. This standard does not apply to wooden pad

23、dles and oars. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 paddle manually operated means of propulsion operated free-handed by a person NOTE It consists of a shaft with a (paddle) blade at the end. The double paddle has a blade at each e

24、nd of the shaft. 2.2 oar manually operated means of propulsion consisting of a shaft and a blade at the end NOTE The oar is pivot-mounted at the hull of a boat in eye lets or oarlocks. Oars can be operated by a person in pair or as single device. 3 Classes and types 3.1 Classes The following perform

25、ance classes apply: class A: higher requirements, appropriate for touring purposes; class B: lower requirements, appropriate for bathing and leisure. 3.2 Types Depiction of examples of paddles and oars: see Figures 1a) to 1e). DIN EN 16083:2012-04EN 16083:2012 (E) 5 a) Type O Oar b) Type S1 Single p

26、addle c) Type S2 Single paddle d) Type D Double paddle e) Type K Combined paddle (convertible single double paddle via couplings) Key 1 shaft 2 blade 3 knob handle 4 gripping area 5 coupling Figure 1 Paddles and oars DIN EN 16083:2012-04EN 16083:2012 (E) 6 4 Safety requirements and testing 4.1 Gener

27、al 4.1.1 Requirement Paddles and oars shall be entirely free from sharp edges, burrs or splinters. There shall be no irregularities which could cause injury. 4.1.2 Testing Visual and tactile testing. 4.2 Temperature Testing shall be done at an air temperature of (20 3) C. 4.3 Bending strength of pad

28、dles and oars 4.3.1 Requirements When tested in accordance with 4.3.2 paddles and oars shall neither break (shaft and blade) nor permanently deform (shaft) in a way that function is impaired. Load for blades of class A paddles/oars: 0,45 N/cm2; Load for blades of class B paddles/oars: 0,30 N/cm2. Th

29、e determination of the blade surface shall be done according to Figure 2. Key B max. width of blade L length up to 0,75 B Figure 2 Loading point DIN EN 16083:2012-04EN 16083:2012 (E) 7 4.3.2 Testing The shaft of the paddle/oar shall be clamped on a rigid surface as shown in Figure 3. The blade shall

30、 be loaded quasi statically (F1) at a loading point on the centre line of the blade (150 5) mm from its end with a vertical force as given in 4.4.1. Duration of each load application: 1 min; Number of applications: 25; In case of double paddles the testing force shall be applied on one blade side on

31、ly. DIN EN 16083:2012-04EN 16083:2012 (E) 8 Dimensions in millimetres a) Type S2 b) Type D c) Type K d) Example of the clamping Key F1test force (see 4.3.1) asectional view; soft foam pad 80 mm x 80 mm x 20 mm (shore hardness A 10 to 20) l length Figure 3 Testing of paddles / oars for bending streng

32、th DIN EN 16083:2012-04EN 16083:2012 (E) 9 Load speed for blades of class A paddles/oars: (0,45 N/cm)/min. Load speed for blades of class B paddles/oars: (0,30 N/cm)/min. 4.4 Resistance against buckling of oars and paddles 4.4.1 Requirements The blade of oars / paddles shall be resistant against buc

33、kling. When loaded with a force of 800 N class A or 400 N class B in axial direction the blade shall not break, sliver or become permanently deformed (bended or buckled) in a way that impairs function. 4.4.2 Testing The blade is loaded during (15 1) s, then release for (15 1) s. Thus, each load last

34、s 30 s, and there are 25 applications, so 13 min 30 s altogether. The paddle/oar may be cut so that the shaft shall be built-in. A compression plate shall load the end of the blade. The blade shall not slip on the compression plate. 4.5 Combined parts, couplings 4.5.1 Requirements After being tested

35、 in accordance with 4.5.2 all parts shall remain fully functional. Couplings shall be capable of manual assembly, without the need for any tool, before and after testing in accordance with 4.5.2. 4.5.2 Testing The shaft of paddle / oar shall be put on a rigid surface. The assembled coupling shall be

36、 loaded quasi statically with a force F2of: 0,45 N/cm blade surface for class A; 0,30 N/cm blade surface for class B. The determination of the blade surface shall be done according to Figure 2. Duration of load application: 2 s; Number of applications: 1 000. Inspection, practical check for function

37、ality. For the testing of coupling to bending see Figure 3. Load speed for blades of class A paddles/oars: (0,225 N/cm)/s. Load speed for blades of class B paddles/oars: (0,15 N/cm)/s. DIN EN 16083:2012-04EN 16083:2012 (E) 10 4.6 Floatability 4.6.1 Requirements Paddles and oars shall remain at a dis

38、tance less than 10 cm from water surface for a duration of not less than 10 min (separable types: each main part of the combined paddle). 4.6.2 Testing Practical test in fresh water. 5 Marking and labelling Paddles, oars or their packaging shall be labelled with the following data: Name or logo of m

39、anufacturer respectively distributor; At least on the packaging: the intended use (sport or bathing/leisure); The conformity of paddles/oars with this standard may be declared in manufacturers responsibility by marking the product with the number of this European Standard. EN 16083 Application; touring application EN 16083 Application; bathing/leisure EXAMPLE EN 16083 Bathing/leisure DIN EN 16083:2012-04