DIN EN 16232-2013 Child use and care articles - Infant swings German version EN 16232 2013《儿童使用和保育用品 婴儿秋千 德文版本EN 16232-2013》.pdf

1、December 2013 Translation by DIN-Sprachendienst.English price group 16No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).I

2、CS 97.190!%*z=“2078726www.din.deDDIN EN 16232Child use and care articles Infant swings;English version EN 16232:2013,English translation of DIN EN 16232:2013-12Artikel fr Suglinge und Kleinkinder Babyschaukeln;Englische Fassung EN 16232:2013,Englische bersetzung von DIN EN 16232:2013-12Articles de p

3、uriculture Balancelles suspendues pour enfant;Version anglaise EN 16232:2013,Traduction anglaise de DIN EN 16232:2013-12www.beuth.deDocument comprises 37 pagesIn case of doubt, the German-language original shall be considered authoritative.11.13 DIN EN 16232:2013-12 2 A comma is used as the decimal

4、marker. Start of application The start of application of this standard is 2013-12-01. National foreword This standard includes safety requirements. This document (EN 16232:2013) has been prepared by Technical Committee CEN/TC 252 “Child use and care articles” (Secretariat: AFNOR, France). The respon

5、sible German body involved in its preparation was the Normenausschuss Sicherheitstechnische Grundstze (Safety Design Principles Standards Committee), Working Committee NA 095-05-03 AA Artikel fr Suglinge und Kleinkinder Sitzen, Pflegen, Schtzen, Liegen und Transportieren. EUROPEAN STANDARD NORME EUR

6、OPENNE EUROPISCHE NORM EN 16232 August 2013 ICS 97.190 English Version Child use and care articles - Infant swings Articles de puriculture - Balancelles suspendues pour enfant Artikel fr Suglinge und Kleinkinder - Babyschaukeln This European Standard was approved by CEN on 5 July 2013. CEN members a

7、re bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to

8、 the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management C

9、entre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithu

10、ania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussel

11、s 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16232:2013: EEN 16232:2013 (E) 2 Contents Page Foreword 4 1 Scope . 5 2 Normative references 5 3 Terms and definitions . 5 4 Test equipment 5 4.1 Articulated test mass 5 4.2 Te

12、st mass A . 6 4.3 Test mass B . 7 4.4 Small parts cylinder 7 4.5 Feeler gauge 8 4.6 Test probes for finger entrapment 8 4.7 Test surface for static slippage 9 4.8 Test surface for stability . 9 4.9 Test equipment for sound level measurement 9 5 General requirements and test conditions . 9 5.1 Produc

13、t conditioning 9 5.2 Test conditions 9 5.3 Application of forces . 10 5.4 Tolerances . 10 5.5 Order of tests. 10 6 Chemical hazards migration of certain elements . 10 7 Thermal hazards 11 8 Mechanical hazards 11 8.1 General 11 8.1.1 Determination of the junction line 11 8.1.2 Determination of protec

14、ted volume 12 8.2 Hazards due to sound level 14 8.2.1 Requirement 14 8.2.2 Test method . 14 8.3 Entrapment hazards 14 8.3.1 Entrapment of fingers . 14 8.4 Hazards due to falling of the child 15 8.4.1 Angles 15 8.4.2 Restraint system . 21 8.5 Hazards due to moving parts 22 8.5.1 Requirements for comp

15、ression points . 22 8.5.2 Requirements for shear points . 22 8.6 Hazards due to folding of the product 22 8.6.1 Requirements 22 8.6.2 Test methods . 23 8.7 Hazards from entanglement in cords, ribbons and similar parts 23 8.7.1 Requirements 23 8.7.2 Test method . 23 8.8 Choking and ingestion hazard 2

16、3 8.8.1 Requirements 23 8.8.2 Test methods . 24 8.9 Suffocation hazards from packaging materials . 25 8.10 Hazards from edges, corners and protruding parts 25 DIN EN 16232:2013-12 EN 16232:2013 (E) 3 8.11 Hazards from inadequate structural integrity 25 8.11.1 Static strength . 25 8.11.2 Durability o

17、f powered swinging mechanisms 25 8.11.3 Reclining system . 26 8.12 Hazards from inadequate stability 26 8.12.1 Requirements 26 8.12.2 Test method for static stability . 26 8.12.3 Test method for dynamic stability 27 8.13 Hazards from possible movement of the infant swing on the floor 27 8.13.1 Requi

18、rement 27 8.13.2 Test method . 27 8.14 Electrical hazards 28 8.14.1 General 28 8.14.2 Leakage prevention . 28 8.14.3 Test methods . 28 9 Product information 29 9.1 General 29 9.2 Marking of the product 29 9.2.1 General requirements . 29 9.2.2 Requirements for infant swings with electrical components

19、 30 9.2.3 Durability of marking . 30 9.2.4 Test method for durability of marking 30 9.3 Purchase information 30 9.4 Instructions for use . 31 9.4.1 General 31 9.4.2 Warnings 31 9.4.3 Additional information 31 9.4.4 Requirements for infant swings with electrical components 32 Annex A (informative) Ra

20、tionales 33 A.1 General (see Clause 1) 33 A.2 Protective volume and protective barriers (see 8.1.2 and 8.1.2.2) 33 A.3 Hazards due to sound level (see 8.2) 33 A.4 Hazards due to detachment of toy bars . 33 A.5 Hazards from possible movement of the infant swing on the floor (see 8.13) . 33 Annex B (i

21、nformative) A-deviation . 34 Bibliography . 35 DIN EN 16232:2013-12 EN 16232:2013 (E) 4 Foreword This document (EN 16232:2013) has been prepared by Technical Committee CEN/TC 252 “Child use and care articles”, the secretariat of which is held by AFNOR. This European Standard shall be given the statu

22、s of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2014, and conflicting national standards shall be withdrawn at the latest by February 2014. Attention is drawn to the possibility that some of the elements of this document may be the su

23、bject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium,

24、Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland

25、, Turkey and the United Kingdom. DIN EN 16232:2013-12 EN 16232:2013 (E) 5 1 Scope This European Standard specifies safety requirements and the corresponding test methods for infant swings intended for children up to a weight of 9 kg or unable to sit up unaided. If an infant swing has several functio

26、ns or can be converted into another function, the relevant European Standards apply to it. Swings falling under the scope of EN 71-8 are excluded from the scope of this European Standard. See rationale in A.1. 2 Normative references The following documents, in whole or in part, are normatively refer

27、enced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 71-3:1994, Safety of toys Part 3: Migration of certain elements EN 1103

28、 Textiles Fabrics for apparel Detailed procedure to determine the burning behaviour EN 61558-2-7, Safety of power transformers, power supplies, reactors and similar products Part 2-7: Particular requirements and tests for transformers and power supplies for toys (IEC 61558-2-7) EN 61558-2-16, Safety

29、 of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode power supply units (IEC 61558-2-16) EN 61672-1, Electroacoustics Sound level meters P

30、art 1: Specifications (IEC 61672-1) EN 61672-2, Electroacoustics Sound level meters Part 2: Pattern evaluation tests (IEC 61672-2) EN 62115:2005, Electric toys Safety (IEC 62115:2003, modified + A1:2004) EN ISO 3746:2010, Acoustics Determination of sound power levels and sound energy levels of noise

31、 sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 infant swing stationary unit with a frame and mechanism that enables a

32、 child unable to sit up unaided to be swung 3.2 junction line intersection of the seat and the backrest 4 Test equipment 4.1 Articulated test mass 9 kg articulated test mass made of steel (see Figure 1). DIN EN 16232:2013-12 EN 16232:2013 (E) 6 Dimensions in millimetres Key 1 part to be placed onto

33、the seat surface 2 part to be placed onto the backrest surface 3 hinge pin made of steel E mass: (4 495 50) g F mass: (4 501 50) g G mass of hinge axle: (17 0,5) g, length: 79,5 mm Mass tolerance: (9 0,1) kg Dimensions tolerance: 2 mm All edges shall be chamfered. Figure 1 Articulated test mass 4.2

34、Test mass A Test mass A is a rigid cylinder (160 5) mm in diameter and (300 5) mm in height, having a mass of ( )0100 9,+kg and with its centre of gravity in the centre of the cylinder. All edges shall have a radius of (5 1) mm. DIN EN 16232:2013-12 EN 16232:2013 (E) 7 Two anchorage points shall be

35、provided. These shall be positioned (150 2,5) mm from the base and at 180 to each other around the circumference (see Figure 2). Dimensions in millimetres Key 1 radius: (5 1) mm 2 two anchorage points Figure 2 Test mass A 4.3 Test mass B Test mass B is a (150 30) mm by (200 30) mm rectangular shaped

36、 sand bag with a mass of (3 0,1) kg. 4.4 Small parts cylinder Small parts cylinder for the assessment of small components, having dimensions in accordance with Figure 3. DIN EN 16232:2013-12 EN 16232:2013 (E) 8 Dimension in millimetres Figure 3 Small parts cylinder 4.5 Feeler gauge Gauge with a thic

37、kness of (0,4 0,02) mm and an insertion edge radius of (3 0,5) mm (see Figure 4). Dimensions in millimetres Figure 4 Feeler gauge 4.6 Test probes for finger entrapment Probes made from plastics or other hard, smooth material of diameters ( )01,0-7 mm and ( )1,0012+mm with a full hemispherical end th

38、at can be mounted on a force-measuring device, see Figure 5. Mesh probe made from plastics or other hard, smooth material as shown in Figure 6. DIN EN 16232:2013-12 EN 16232:2013 (E) 9 Dimensions in millimetres Key (dimensions in millimetres) Probe type 7mm probe 12mm probe Diameter A 01,0-71,0012+R

39、adius RB 3,5 0,2 6 0,2 1 line scribed around circumference showing depth of penetration Figure 5 Test probes with hemispherical end Figure 6 Test probe for mesh 4.7 Test surface for static slippage Rigid plane covered with uncoated tempered float glass with a smooth surface and thickness of (6 0,5)

40、mm, inclined at angle of (12 + 0,5/0) to the horizontal. 4.8 Test surface for stability Test surface, inclined at (15 + 0,5/0) to the horizontal, covered with aluminium oxide paper of grade 80. 4.9 Test equipment for sound level measurement The instrumentation system, including the microphone and ca

41、ble, shall meet the requirements of a type 1 or type 2 instrument specified in EN 61672-1 and EN 61672-2. When measuring high peak emission sound pressure levels, the microphone and the entire instrumentation system shall have the capability of handling linear peak levels at least up to 125 dB. 5 Ge

42、neral requirements and test conditions 5.1 Product conditioning Before testing, any fabrics used shall be cleaned or washed and dried twice in accordance with the manufacturers instructions. 5.2 Test conditions The tests shall be carried out in ambient conditions of (20 5) C. DIN EN 16232:2013-12 EN

43、 16232:2013 (E) 10 The tests are designed to be applied to infant swings that are fully assembled and ready for use in accordance with the manufacturers instructions. If the infant swing can be assembled or adjusted in different ways, the most onerous combinations shall be used for each test. If the

44、 infant swing has any battery-powered mechanism, it shall be tested using new non-rechargeable alkaline batteries; if the infant swing is supplied with its own rechargeable battery pack, it shall be tested with the battery pack fully charged in accordance with the instructions for use. The batteries

45、 used are those with the voltage and size specified on the infant swing or in the instructions. Lithium batteries or rechargeable batteries shall not be used unless their use is recommended in the instructions. If the infant swing fails to withstand a test and this could be due to a defective batter

46、y, the test shall be repeated with a new set of batteries. 5.3 Application of forces The forces in the static load tests shall be applied sufficiently slowly to ensure that negligible dynamic force is applied. 5.4 Tolerances Unless otherwise stated, the accuracy of the test equipment shall be: Force

47、s: 5 % of the nominal force; Masses: 0,5 % of the nominal mass; Dimensions: 0,5 mm of the nominal dimension; Angles: 0,5 of the nominal angle; The tests are described in terms of the application of forces. Masses can however be used. The relationship 10 N = 1 kg may be used for this purpose. Unless

48、otherwise specified, the test forces may be applied by any suitable device which does not adversely affect the results. 5.5 Order of tests Unless otherwise stated in the test methods, the tests shall be carried out on the same infant swing in the order listed in this standard. 6 Chemical hazards migration of certain elements The migration of synthetic or natural elements from coatings of paint, varnish, lacquer, polymer and similar coating