DIN EN 16261-2-2013 Pyrotechnic articles - Fireworks Category 4 - Part 2 Requirements German version EN 16261-2 2012《烟火制品 4类烟火 第2部分 要求 德文版本EN 16261-2-2012》.pdf

1、March 2013 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、71.100.30!$0“1961394www.din.deDDIN EN 16261-2Pyrotechnic articles Fireworks, Category 4 Part 2: Requirements;English version EN 16261-2:2012,English translation of DIN EN 16261-2:2013-03Pyrotechnische Gegenstnde Feuerwerkskrper, Kategorie 4 Teil 2: Anforderungen;Englische Fassung EN 16261-2:2012,Eng

3、lische bersetzung von DIN EN 16261-2:2013-03Articles pyrotechniques Artifices de divertissement, Catgorie 4 Partie 2: Exigences;Version anglaise EN 16261-2:2012,Traduction anglaise de DIN EN 16261-2:2013-03www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.D

4、ocument comprises 22 pages 02.13 DIN EN 16261-2:2013-03 2 A comma is used as the decimal marker. National foreword This document (EN 16261-2:2013) has been prepared by Technical Committee CEN/TC 212 “Pyrotechnic articles” (Secretariat: NEN, Netherlands). The responsible German body involved in its p

5、reparation was the Normenausschuss Materialprfung (Materials Testing Standards Committee), Working Committee NA 062-08-81 AA Pyrotechnische Gegen-stnde. The Committee would like to bring attention to the fact that the following legal provisions are to be observed when applying DIN EN 16261-2 in Germ

6、any: Gesetz ber explosionsgefhrliche Stoffe (Sprengstoffgesetz - SprengG) (German Explosives Act) of 10 September 2002 (BGBl. I, p. 3518), as amended by the Viertes Gesetz zur nderung des Sprengstoffgesetzes (Fourth Act Amending the Explosives Act) of 17 July 2009 (BGBl. I, p. 2062)*) Erste Verordnu

7、ng zum Sprengstoffgesetz (1. SprengV) (First Ordinance on the Explosives Act) of 31 January 1991 (BGBl. I, p. 169), as amended by the Viertes Gesetz zur nderung des Spreng-stoffgesetzes (Fourth Act Amending the Explosives Act) of 17 July 2009 (BGBl. I, p. 2062)*) The DIN Standard corresponding to th

8、e International Standard referred to in this document is as follows: ISO 2859-1 DIN ISO 2859-1 National Annex NA (informative) Bibliography DIN ISO 2859-1, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection *)

9、Registered in the DITR database of DIN Software GmbH, obtainable from: Beuth Verlag GmbH, 10772 Berlin. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16261-2 January 2013 ICS 71.100.30 English Version Pyrotechnic articles - Fireworks, Category 4 - Part 2: Requirements Articles pyrotechniques

10、- Artifices de divertissement, Catgorie 4 - Partie 2: Exigences Pyrotechnische Gegenstnde - Feuerwerkskrper, Kategorie 4 - Teil 2: Anforderungen This European Standard was approved by CEN on 24 November 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate t

11、he conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standar

12、d exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the nation

13、al standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slova

14、kia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved wo

15、rldwide for CEN national Members. Ref. No. EN 16261-2:2013: EEN 16261-2:2013 (E) 2 Contents Page Foreword . 4 1 Scope 5 2 Normative references . 5 3 Terms and definitions 5 4 Pyrotechnic composition . 6 5 Construction (type test and batch test) . 6 6 Means of ignition 6 6.1 Identification (type test

16、 and batch test) . 6 6.2 Protection (type test and batch test) . 6 7 Performance . 6 7.1 Properties to be checked before functioning tests 6 7.1.1 Loose pyrotechnic composition after mechanical conditioning (type test) 6 7.1.2 Integrity (type test and batch test) 7 7.2 Properties to be checked durin

17、g functioning tests 7 7.2.3 Stability during functioning (type test and batch test) . 7 7.2.4 Performance parameters (type test and batch test) . 7 7.2.5 Sound pressure level (type test and batch test) . 8 7.3 Requirements for components (type test and batch test) 8 8 Protective pack (type test and

18、batch test) 8 9 Type testing 9 9.1 General . 9 9.2 Number of items to be tested 9 9.3 Fireworks supplied in protective packs 9 9.4 Test report 10 10 Batch testing 10 10.1 General . 10 10.2 Sampling plans. 10 10.2.1 General sampling plans . 10 10.2.2 Sample size for small batches (destructive tests)

19、10 10.3 Fireworks in protective packs . 10 10.4 Nonconformities . 10 10.4.1 Construction and performances 10 10.4.2 Labelling . 12 10.5 Test report 12 10.6 Acceptance or rejection of a batch 12 10.6.1 Nonconforming units . 12 10.6.2 Critical nonconforming units . 13 10.6.3 Major nonconforming units

20、. 13 10.6.4 Minor nonconforming units . 13 Annex A (normative) Mandatory performance parameters . 14 Annex B (normative) List of nonconformities for Category 4 fireworks regarding safety in functioning . 17 Annex C (informative) Overview of essential safety requirements and corresponding clauses of

21、all parts of this European Standard. 19 DIN EN 16261-2:2013-03 EN 16261-2:2013 (E) 3 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2007/23/EC on the placing on the market of pyrotechnic articles 20 DIN EN 16261-2:2013-03 EN 16261-2:

22、2013 (E) 4 Foreword This document (EN 16261-2:2013) has been prepared by Technical Committee CEN/TC 212 “Pyrotechnic articles”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorseme

23、nt, at the latest by July 2013, and conflicting national standards shall be withdrawn at the latest by July 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any

24、 or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral p

25、art of this document. This European Standard is one of the series of standards as listed below: EN 16261-1, Pyrotechnic articles Fireworks, Category 4 Part 1 Terminology; EN 16261-3, Pyrotechnic articles Fireworks, Category 4 Part 3 Test methods; EN 16261-4, Pyrotechnic articles Fireworks, Category

26、4 Part 4 Minimum labelling requirements and instructions for use. CEN/TC 212 has also developed European Standards for: Pyrotechnic articles Fireworks Categories 1, 2 and 3; Pyrotechnic articles Theatrical pyrotechnic articles; Pyrotechnic articles Pyrotechnic articles for vehicles; Pyrotechnic arti

27、cles Other pyrotechnic articles; Pyrotechnic articles Ignition devices. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denma

28、rk, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 16261-2:

29、2013-03 EN 16261-2:2013 (E) 5 1 Scope This European Standard specifies requirements for the construction, performance and protective packaging of Category 4 fireworks, as listed in EN 16261-1. This European Standard does not apply for articles containing pyrotechnic compositions that include any of

30、the following substances: arsenic or arsenic compounds; polychlorobenzenes; lead or lead compounds; mercury compounds; white phosphorus; picrates or picric acid. This European Standard does not apply for articles containing military explosives or commercial blasting agents except for black powder or

31、 flash composition. In addition, any European regulation regarding forbidden substances should be taken into account. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only

32、 the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 16261-1:2012, Pyrotechnic articles Fireworks, Category 4 Part 1: Terminology EN 16261-3:2012, Pyrotechnic articles Fireworks, Category 4 Part 3: Test methods EN 16

33、261-4:2012, Pyrotechnic articles Fireworks, Category 4 Part 4: Minimum labelling requirements and instructions for use ISO 2859-1, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection. 3 Terms and definitions Fo

34、r the purposes of this document, the terms and definitions given in EN 16261-1:2012 apply. DIN EN 16261-2:2013-03 EN 16261-2:2013 (E) 6 4 Pyrotechnic composition No limits are given for the net explosive content (NEC)1)of Category 4 articles in this standard. 5 Construction (type test and batch test

35、) When tested in accordance with 6.1 and 6.2 of EN 16261-3:2012, the article dimensions and gross mass shall be in accordance with the manufacturers declaration (including tolerances). The orientation of mortars shall be verified by inspection according to 6.3 of EN 16261-3:2012, during type test. W

36、hen the orientation of mortars in combinations is not visible, the maximum firing angle shall be displayed on the label and verified by visual inspection according to 6.7 of EN 16261-3:2012. 6 Means of ignition 6.1 Identification (type test and batch test) The means of ignition shall be clearly visi

37、ble or shall be indicated by labelling or instructions where applicable. Conformity to this requirement shall be verified by visual examination according to 6.7 of EN 16261-3:2012. 6.2 Protection (type test and batch test) Where appropriate, the means of ignition shall be protected to avoid accident

38、al ignition of the fireworks. Conformity to this requirement shall be verified by visual examination according to 6.7 of EN 16261-3:2012. 7 Performance 7.1 Properties to be checked before functioning tests 7.1.1 Loose pyrotechnic composition after mechanical conditioning (type test) When tested in a

39、ccordance with 6.8 of EN 16261-3:2012, the loose pyrotechnic composition found outside the article after mechanical conditioning shall be weighed. The mass of the whole loose material shall comply with manufacturers specifications (if any) and the mass of loose pyrotechnic composition shall not exce

40、ed 3 % of the NEC and not more than 1 g for each item tested. If the pyrotechnic composition cannot be separated from the loose material, the same limits shall apply to the whole loose material. 1) The NEC has an influence (directly or indirectly) on the safety distances. For Category 4 fireworks, i

41、t is agreed that no fixed minimum safety distances are defined, contrary to Category 1, 2 and 3 fireworks. The safe use of Category 4 fireworks is one of the major responsibilities of the person with specialist knowledge who should determine the minimum safety distance by using the information given

42、 in prEN 16261-4:2011, Clause 4. DIN EN 16261-2:2013-03 EN 16261-2:2013 (E) 7 7.1.2 Integrity (type test and batch test) 7.1.2.1 General requirements There shall be no holes, splits, dents or bulges either in the body of the firework case or in the end closures, except those technically necessary fo

43、r the correct functioning of the firework. If the end closures are separate components, they shall be in place. There shall be no pyrotechnic leakage of the article to be tested when it is received for testing. Conformity to these requirements shall be verified by visual examination according to 6.7

44、 of EN 16261-3:2012. 7.1.2.2 Specific requirements For combinations: each individual element shall be securely attached to the other elements or to the framework. Attachment by the transmitting fuse(s) alone shall be allowed if it is sufficient to keep the elements joined together during normal hand

45、ling. Conformity to above requirements shall be checked by visual examination according to 6.7 of EN 16261-3:2012. 7.2 Properties to be checked during functioning tests 7.2.1 Principal effects (type test and batch test) When tested in accordance with 6.10 of EN 16261-3:2012, the principal effects of

46、 each firework shall conform to those specified by the manufacturer or importer as described in EN 16261-1. 7.2.2 Functioning (type test and batch test) For type test only, functioning test in accordance with 6.10 of EN 16261-3:2012, shall be performed in as received conditions and, after mechanical

47、 and thermal conditions in accordance with 6.8 and 6.9 of EN 16261-3:2012. For type test and batch test, when tested in accordance with 6.10 of EN 16261-3:2012, the article shall function as intended and shall not function in an erratic and unforeseeable manner. 7.2.3 Stability during functioning (t

48、ype test and batch test) When used according to the instructions for use, the article shall remain in its initial position and maintain its integrity whilst functioning, if applicable. Conformity to these requirements shall be checked by the method described in 6.10 of EN 16261-3:2012. 7.2.4 Performance parameters (type test and batch test) The mandatory parameters listed in Annex A shall be measured and recorded according to 6.4, 6.5, 6.10.3 and 6.10.4 of EN 16261-3: