DIN EN 16342-2013 Cosmetics - Analysis of cosmetic products - Quantitative determination of zinc pyrithione piroctone olamine and climbazole in surfactant containing cosmetic anti-.pdf

1、August 2013 Translation by DIN-Sprachendienst.English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、71.100.70!%($O“2050144www.din.deDDIN EN 16342Cosmetics Analysis of cosmetic products Quantitative determination of zinc pyrithione, piroctone olamine andclimbazole in surfactant containing cosmetic anti-dandruff products;English version EN 16342:2013,English translation of DIN EN 16342:2013-08Kosmet

3、ische Mittel Untersuchung von kosmetischen Mitteln Quantitative Bestimmung von Zinkpyrithion, Pirocton-Olamin und Climbazol intensidhaltigen kosmetischen Mitteln mit Antischuppenwirkstoffen;Englische Fassung EN 16342:2013,Englische bersetzung von DIN EN 16342:2013-08Cosmtiques Analyse des produits c

4、osmtiques Dtermination quantitative de la pyrithione de zinc, de la piroctone olamine et duclimbazole dans les produits cosmtiques antipelliculaires contenant des agents desurface;Version anglaise EN 16342:2013,Traduction anglaise de DIN EN 16342:2013-08www.beuth.deDocument comprises pagesIn case of

5、 doubt, the German-language original shall be considered authoritative.1507.13 DIN EN 16342:2013-08 2 A comma is used as the decimal marker. National foreword This document (EN 16342:2013) has been prepared by Technical Committee CEN/TC 392 “Cosmetics” (Secretariat: AFNOR, France). The responsible G

6、erman body involved in its preparation was the Normenausschuss Lebensmittel und landwirtschaftliche Produkte (Food and Agricultural Products Standards Committee), Working Committee NA 057-07-01 AA Kosmetische Mittel. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16342 May 2013 ICS 71.100.70 E

7、nglish Version Cosmetics - Analysis of cosmetic products - Quantitative determination of zinc pyrithione, piroctone olamine and climbazole in surfactant containing cosmetic anti-dandruff products Cosmtiques - Analyse des produits cosmtiques - Dtermination quantitative de la pyrithione de zinc, de la

8、 piroctone olamine et du climbazole dans les produits cosmtiques antipelliculaires contenant des agents de surface Kosmetische Mittel - Untersuchung von kosmetischen Mitteln - Quantitative Bestimmung von Zinkpyrithion, Pirocton-Olamin und Climbazol in tensidhaltigen kosmetischen Mitteln mit Antischu

9、ppenwirkstoffen This European Standard was approved by CEN on 25 April 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibli

10、ographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the respons

11、ibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Repub

12、lic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMAL

13、ISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16342:2013: EEN 16342:2013 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 5 2

14、Terms and definitions .5 3 Principle 5 4 Reagents .5 5 Apparatus and equipment 7 6 Sampling .7 7 Procedure .8 8 Evaluations .9 9 Test report . 10 Annex A (informative) Results of the inter-laboratory test . 11 Annex B (informative) Sample Chromatogram 12 Bibliography . 13 DIN EN 16342:2013-08 EN 163

15、42:2013 (E) 3 Foreword This document (EN 16342:2013) has been prepared by Technical Committee CEN/TC 392 “Cosmetics”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at t

16、he latest by November 2013, and conflicting national standards shall be withdrawn at the latest by November 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any

17、 or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republ

18、ic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 16342:2013-08 EN 16342:2013 (E) 4 Introduction Speci

19、al hair products contain substances to help prevent dandruff. These substances mainly inhibit the development of microorganisms, which often are the cause of dandruff. The most commonly used substances are zinc pyrithione, piroctone olamine and climbazole. The substances are regulated by Council Dir

20、ective of 27 July 1976 on the approximation of the laws of the member states relating to cosmetic products (EC 76/768/EEC) as well as Regulation (EC) No 1223/2009 of the European Parliament and of the Council of 30 November 2009 on cosmetic products. Limits for these substances are listed in the ann

21、exes regulating preservatives in cosmetic products. Zinc pyrithione is additionally listed in Annex III of both regulative documents named above. NOTE As the Regulation (EC) 1223/2009 applies in total from 11 July 2013 and replaces Directive 76/768/EEC the following details relate only to Regulation

22、 (EC) 1223/2009. Reference Number, maximum authorised concentration in hair products, limitations and requirements: Annex III Regulation (EC) 1223/2009 Zinc pyrithione: No. 101: 0,1 % leave-on hair products Remark: For purposes other than inhibiting the development of microorganisms in the product.

23、This purpose has to be apparent from the presentation of the product. Annex V Regulation (EC) 1223/2009 Zinc pyrithione: No. 8: 1,0 % hair products Remark: Only in rinse-off products 0,5 % other products Remark: Not to be used in oral products Climbazole: No. 32: 0,5 % Piroctone olamine: No. 35: 1,0

24、 % rinse-off products 0,5 % other products DIN EN 16342:2013-08 EN 16342:2013 (E) 5 1 Scope This European Standard specifies an analytical method for the detection and quantitative determination of the following anti-dandruff agents: zinc pyrithione, piroctone olamine and climbazole in surfactant-co

25、ntaining cosmetic products in the concentration range from 0,1 g/100 g to 1,0 g/100 g. NOTE The method is also suitable for the determination of ketoconazole and ciclopirox olamine (q.v. Annex A) in surfactant-containing cosmetic products and it is probably applicable for the determination of the su

26、bstances in non surfactant-containing cosmetic products. For these purposes, the method has not been validated. 2 Terms and definitions For the purposes of this document, the following term and definition applies. 2.1 anti-dandruff agents substances, added to hair care products, active against the d

27、evelopment of microorganism e.g. zinc pyrithione, piroctone olamine and climbazole 3 Principle The anti-dandruff agents are extracted from the cosmetic sample matrix using dichloromethane and methanol. Each analyte present in the sample extract is separated using reversed phase HPLC with UV (DAD) de

28、tection. The quantitative determination is made using the external standard method of calibration. 4 Reagents 4.1 General If not otherwise specified, as a minimum analytical-grade chemicals shall be used; water shall be distilled or of a corresponding purity. “Solution“ shall be understood as an aqu

29、eous solution unless otherwise specified. 4.2 Methanol, CAS number: 67-56-1. 4.3 Dichloromethane, CAS number: 75-09-02. 4.4 Acetonitrile, CAS number: 75-05-8. 4.5 Ethylenediaminetetraacetic acid (EDTA) disodium salt dihydrate (Na2EDTA 2H2O), CAS number: 6381-92-6. 4.6 Oxalic acid dihydrate, CAS numb

30、er: 6153-56-6. 4.7 Acetic acid (glacial), CAS number: 64-19-7, mass fraction w = 99,8 g/100 g. 4.8 Acetic acid, molar concentration c = 0,02 mol/l. Weigh 1,20 g of acetic acid glacial (4.7) into a 1-l-volumetric flask and fill with water up to the calibration mark. 4.9 Methanol/acetic acid mixture M

31、ix 80 parts by volume of methanol (4.2) and 20 parts by volume of acetic acid (4.8). DIN EN 16342:2013-08 EN 16342:2013 (E) 6 4.10 Sodium hydroxide solution, molar concentration c = 1 mol/l. 4.11 Eluents 4.11.1 Eluent A: 0,002 7 mol/l of oxalic acid dihydrate (4.6) and 0,001 mol/l of EDTA (4.5) in w

32、ater, pH 4,0: Pre-dissolve 0,37 g of EDTA in water, add 0,35 g of oxalic acid dihydrate (0,025 % of oxalic acid) and adjust to pH = 4,0 with sodium hydroxide solution (4.10) using a pH-Meter. Then fill with water up to the 1000 ml mark. 4.11.2 Eluent B: Acetonitrile (4.4). 4.12 Reference substances

33、4.12.1 General For the reference substances, no purity is defined. However, the purity of the reference substances shall be known to determine the definite amount of standard in the calibration solution. 4.12.2 Zinc pyrithione, CAS number: 13463-41-7. 4.12.3 Piroctone olamine, (1-hydroxy-4-methyl-6-

34、(2,4,4-trimethylpentyl)-2-pyridone), CAS number: 68890-66-4. 4.12.4 Climbazole, (1-(4-chlorophenoxy)-1-(imidazol-1-yl)-3,3-dimethyl-2-butanone), CAS number: 38083-17-9. 4.13 Stock solutions 4.13.1 General Fresh stock solutions need to be prepared each working day. 4.13.2 Zinc pyrithione stock soluti

35、on, mass concentration = 250 mg/l. Weigh approximately 25 mg of zinc pyrithione (4.12.2) to the nearest 0,1 mg into a 100-ml-volumetric flask, dissolve in 50 ml of dichloromethane (4.3) and fill up to the mark with the methanol/acetic acid mixture (4.9). 4.13.3 Piroctone olamine and climbazole stock

36、 solution, mass concentration = 250 mg/l. Weigh approximately 25 mg of each piroctone olamine (4.12.3) and climbazole (4.12.4) to the nearest 0,1 mg into a 100-ml-volumetric flask and fill up to the mark with the methanol/acetic acid mixture (4.9). 4.14 Calibration solutions Fresh calibration soluti

37、ons shall be prepared each working day. The following scheme in Table 1 for the preparation of the calibration solutions has proved useful in practice. Together, the given amounts of the stock solutions in ml, are pipetted into 25-ml-volumetric flask and filled up to the mark with the methanol/aceti

38、c acid mixture (4.9). For calculation the concentration of the calibration solutions have to be corrected with the known purity of the reference substances. DIN EN 16342:2013-08 EN 16342:2013 (E) 7 Table 1 Calibration solution Calibration solution Zinc pyrithione (4.13.2) ml Piroctone olamine + Clim

39、bazole (4.13.3) ml Concentration g/ml 1 0,5 0,5 5 2 1 1 10 3 2 2 20 4 3 3 30 5 5 5 50 5 Apparatus and equipment 5.1 Analytical balance, with a precision of 0,1 mg. 5.2 Membrane filter, for solvent filtration, 0,45 m pore size. 5.3 Ultrasonic bath, with temperature controlled heater. 5.4 Disposable s

40、yringes 5.5 Membrane filter, for sample filtration, e.g. PTFE, 0,45 m pore size. 5.6 High-performance liquid chromatograph, consisting of: sampling device; pump system with gradient function; degasser (optionally; eluent may be degassed prior to use if the system requirements are fulfilled (q.v.); c

41、olumn oven; photodiode array detector (for quantitative determination without identification a multiple wavelength detector is sufficient); evaluation system. 5.7 Analytical reversed-phase separation column, e.g.: Onyx Monolithic C18 100 mm 3 mm (Phenomenex)1)or Chromolith RP18e, 100 mm 3 mm (Merck)

42、1). A pre-column packed with stationary phase similar to the analytical separation column shall be used. 6 Sampling The sampling technique is not part of the technique specified in the standard method. 1) This is an example of a suitable product available commercially. This information is given for

43、the convenience of users of this document and does not constitute an endorsement by CEN of this product. Equivalent products may be used if they can be shown to lead to the same results. DIN EN 16342:2013-08 EN 16342:2013 (E) 8 7 Procedure 7.1 Sample preparation Weigh approximately 250 mg of sample

44、to the nearest 0,1 mg into a 50-ml-volumetric flask. Add 5 ml of dichloromethane (4.3) and 5 ml of methanol (4.2). Place the volumetric flask into a temperature controlled ultrasonic bath for 10 min and heat gently at 35 C to 40 C. When the sample is dissolved or homogeneously dispersed, let the sam

45、ple cool down at room temperature. Fill the volumetric flask to the mark with methanol/acetic acid (4.9) and shake. Filter approximately 2 ml of methanol/acetic acid mixture through a membrane filter (5.5) into a HPLC vial, discarding the first 0,5 ml. Fresh sample solutions shall be prepared each w

46、orking day. 7.2 High-performance liquid chromatography (HPLC) When starting measurements, examine the baseline stability and response linearity of the detector. The detector shall be able to detect the lowest calibration solution of climbazole (5 g/ml) at a signal to noise ratio of 6:1. The same ope

47、rating conditions of the HPLC System shall be maintained throughout the measurements of all sample and calibration solutions. When using the apparatus (5.6) and the column of (5.7), the following conditions have shown useful: flow: 2,0 ml/min injection volume: 5 l injector temperature: room temperat

48、ure column temperature: 30 C detection: Zinc pyrithione: detection wavelength: = 340 nm Climbazole: detection wavelength: = 277 nm Piroctone olamine: detection wavelength: = 305 nm running time: 6 min 7.3 Gradient elution Eluent A: 0,002 7 mol/l of oxalic acid + 0,001 mol/l of EDTA in water, pH 4,0 (4.11.1). Eluent B: Acetonitrile (4.4). For the gradient elution eluents A and B are used in accordance with the volume ratios and time intervals given in Table 2, the following conditions have prov