DIN EN 16397-2-2015 Flexible couplings - Part 2 Characteristics and testing for metal banded flexible couplings adaptors and bushes German version EN 16397-2 2014《挠性联轴节 第2部分 金属绑带的挠.pdf

1、January 2015 Translation by DIN-Sprachendienst.English price group 15No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 23.040.60!%?DL“2283341www.din.deDDIN EN 16397-2Flexible couplings Part 2: Characteristics and testing for metal banded flexible couplings,adaptors and bushes;English version EN 16397-2:2014,English translation of DIN EN 16397-2:2015-01Flexible Kupplungen Teil 2: Eigenschaften und Prfung von flexib

3、len Kupplungen, bergangsbauteilen undAusgleichsringen mit Metallband;Englische Fassung EN 16397-2:2014,Englische bersetzung von DIN EN 16397-2:2015-01Raccords flexibles Partie 2: Caractristiques et essais des raccords flexibles quips de bandes mtalliques,des raccords dadaptation et des bagues;Versio

4、n anglaise EN 16397-2:2014,Traduction anglaise de DIN EN 16397-2:2015-01See start of applicationwww.beuth.deDocument comprises 33 pagesIn case of doubt, the German-language original shall be considered authoritative.12.14DIN EN 16397-2:2015-01 2 A comma is used as the decimal marker. Start of applic

5、ation It should be noted that, in Germany, CE conformity marking of construction products will be permitted once this standard has been listed in the Official Journal of the European Union and/or the Bundesanzeiger (German Federal Gazette) and from the date given therein. For further information, us

6、ers of this standard should refer to the websites of the European Commission or of the relevant building authority. National foreword This document (EN 16397-2:2014) has been prepared by Technical Committee CEN/TC 165 “Waste water engineering” (Secretariat: DIN, Germany). The preliminary work was do

7、ne by Working Group WG 1 “General requirements for pipes”. The responsible German body involved in its preparation was the DIN-Normenausschuss Wasserwesen (DIN Standards Committee Water Practice), Working Committee NA 119-05-09 AA Allgemeine Anforderungen an Rohre, Rohrverbindungen etc. fr Abwasserk

8、anle und -leitungen. The following abbreviations are used in this standard: AVCP Assessment and verification of constancy of performance a.o. title of Clause 6 CWFT Classification without further testing a.o. in Subclause 6.2.1 The European Standards referred to in this document have been published

9、as DIN EN or DIN EN ISO Standards with the same number. The DIN Standard corresponding to the International Standard referred to in this document is as follows: ISO 3302-1 DIN ISO 3302-1 National Annex NA (informative) Bibliography DIN ISO 3302-1, Rubber Tolerances for products Part 1: Dimensional t

10、olerances EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16397-2 November 2014 ICS 23.040.60 English Version Flexible couplings - Part 2: Characteristics and testing for metal banded flexible couplings, adaptors and bushes Raccords flexibles - Partie 2: Caractristiques et essais des raccords f

11、lexibles quips de bandes mtalliques, des raccords dadaptation et des bagues Flexible Kupplungen - Teil 2: Eigenschaften und Prfung von flexiblen Kupplungen, bergangsbauteilen und Ausgleichsringen mit Metallband This European Standard was approved by CEN on 30 August 2014. CEN members are bound to co

12、mply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENEL

13、EC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the

14、same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembou

15、rg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

16、2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16397-2:2014 EEN 16397-2:2014 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Characteristics .8 4.1 General 8 4.2 Materials .8 4.2

17、.1 Stainless steel 8 4.2.2 Rubber 8 4.3 Product characteristics .9 4.3.1 Dimensional tolerances 9 4.3.2 Tightness of joint assemblies . 10 4.3.3 Strength of clamping and shear bands 10 4.3.4 Reaction to fire 11 4.3.5 Durability . 11 4.3.6 Dangerous substances 11 5 Test methods . 11 5.1 Clamping band

18、 assembly torque tests . 11 5.1.1 Apparatus 11 5.1.2 Procedure 11 5.2 Clamping and shear band fixing strength test 11 5.2.1 Apparatus 11 5.2.2 Procedure 11 6 Assessment and verification of constancy of performance - AVCP . 12 6.1 General . 12 6.2 Type testing . 12 6.2.1 General . 12 6.2.2 Test sampl

19、es, testing and compliance criteria 14 6.2.3 Test reports . 15 6.3 Factory production control (FPC) . 15 6.3.1 General . 15 6.3.2 Requirements 15 6.3.3 Product specific requirements 18 6.3.4 Procedure for modifications 19 7 Marking, labelling and packaging . 19 Annex ZA (informative) Relationship be

20、tween this European Standard and the Essential Requirements of EU Construction Products Regulations . 21 Bibliography . 31 DIN EN 16397-2:2015-01 EN 16397-2:2014 (E) 3 Foreword This document (EN 16397-2:2014) has been prepared by Technical Committee CEN/TC 165 “Wastewater engineering”, the secretari

21、at of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2015 and conflicting national standards shall be withdrawn at the latest by August 2016. Attention is drawn to the p

22、ossibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Tra

23、de Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. EN 16397, Flexible couplings, contains the following parts: Part 1: Performance requirements; Part 2: Characteristics a

24、nd testing for metal banded flexible couplings, adaptors and bushes. This standard takes into account the requirements of EN 476. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria,

25、 Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, S

26、witzerland, Turkey and the United Kingdom. DIN EN 16397-2:2015-01 EN 16397-2:2014 (E) 4 1 Scope This European Standard specifies the materials and dimensions for metal banded flexible couplings and adaptors and bushes for use with pipes and fittings in drain and sewer systems, usually operated under

27、 gravity and periodic hydraulic surcharge, both above and below ground inside or outside buildings and intended to connect pipes for: repair of damaged pipelines; connecting pipes of different materials and/or diameters; jointing short/cut lengths of pipe; jointing specific pipe systems; jointing po

28、st-inserted preformed junctions. The coupling consists of a moulded or extruded rubber sleeve with two stainless steel clamping bands with or without a stainless steel shear band. The clamping bands enable the sleeve to form a seal with the pipes to be joined. The shear band gives resistance to shea

29、r forces. Connections may be made between pipes which cannot be satisfactorily joined by a coupling alone, of dissimilar sizes or material, by using an appropriate bush or bushes with the coupling or by using an appropriate adaptor. 2 Normative references The following documents, in whole or in part

30、, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 681-1, Elastomeric seals - Materials requirement

31、s for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber EN 10088-1:2014, Stainless steels Part 1: List of stainless steels EN 10088-2, Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purpo

32、ses EN 10151:2002, Stainless steel strip for springs - Technical delivery conditions EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using data from reaction to fire tests EN 16397-1:2014, Flexible couplings Part 1: Performance requirements EN IS

33、O 7500-1, Metallic materials - Verification of static uniaxial testing machines - Part 1: Tension/compression testing machines - Verification and calibration of the force-measuring system (ISO 7500-1) EN ISO 9445-1:2010, Continuously cold-rolled stainless steel - Tolerances on dimensions and form -

34、Part 1: Narrow strip and cut lengths (ISO 9445-1:2009) ISO 3302-1:2014, Rubber Tolerances for products Part 1: Dimensional tolerances 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. DIN EN 16397-2:2015-01 EN 16397-2:2014 (E) 5 3.1 metal banded fl

35、exible coupling moulded or extruded and joined rubber sleeve, with or without bushes or shear band, with adjustable stainless steel clamping bands by which it is secured to the pipe ends 3.1.1 Type 1 coupling (without shear band) moulded or extruded and joined rubber sleeves with adjustable stainles

36、s steel clamping bands by which it is secured to the pipe ends without shear band Note 1 to entry: An example of a typical Type 1 coupling is shown in Figure 1. Key 1 pipe 1 2 clamping band with drive unit 3 sleeve 4 pipe 2 b width of sleeve d3outside diameter NOTE More than one drive unit could be

37、used where required. Figure 1 Example of Type 1 coupling (without shear band) 3.1.2 Type 2 coupling (with shear band) moulded or extruded and joined rubber sleeve with adjustable stainless steel clamping bands by which it is secured to the pipe ends and a shear band to give resistance to shear loads

38、 Note 1 to entry: An example of a typical Type 2 coupling is shown in Figure 2 and Figure 3. DIN EN 16397-2:2015-01 EN 16397-2:2014 (E) 6 Key 1 pipe 1 2 pipe 2 3 drive unit 4 adjustor unit 5 shear band 6 sleeve 7 clamping band b width of sleeve d3outside diameter NOTE More than one drive unit could

39、be used where required. Figure 2 Example of Type 2 coupling (with shear band) Key 1 shear band adjustors Figure 3 Example of elevation showing shear band adjustors DIN EN 16397-2:2015-01 EN 16397-2:2014 (E) 7 3.2 metal banded adaptor moulded stepped rubber sleeve with adjustable stainless steel clam

40、ping bands by which it is secured to pipes of different outside diameters Note 1 to entry: Adaptors may incorporate an abrupt change of section. An example of a metal banded adaptor is shown in Figure 4. Key 1 pipe 1 2 pipe 2 3 moulded rubber 4 drive unit 5 clamping band b width of sleeve d3outside

41、diameter NOTE More than one drive unit could be used where required. Figure 4 Example of metal banded adaptor 3.3 bush moulded or extruded and joined rubber section only used with couplings having shear bands to compensate for variations between the outside diameters of pipes which cannot be satisfa

42、ctorily joined by a coupling alone 3.4 nominal size of a flexible coupling and an adaptor maximum outside diameter of the pipes with which a flexible coupling or adaptor can be used DIN EN 16397-2:2015-01 EN 16397-2:2014 (E) 8 3.5 shear band component for bearing of shear loads after installation 3.

43、6 clamping band means of clamping the flexible coupling to a pipe using a specified force 3.7 adjustor strip shear band fixing means of clamping the shear band to the flexible coupling using a specified force 4 Characteristics 4.1 General Metal banded flexible couplings and adaptors and bushes shall

44、 be free from such defects as would impair their function when in service. Coupling, adapter and bush size is defined by the range of pipe outside diameter (OD) with which it will meet the performance requirements of this European Standard. 4.2 Materials 4.2.1 Stainless steel Stainless steels used f

45、or clamping bands, shear band clamps and adjustor units shall be either 1.4307, 1.4301, 1.4404, 1.4401, 1.4571, 1.4303 or 1.4567 listed in EN 10088-1:2014, Table 4 or have equivalent or greater corrosion resistance. The components formed from strip material shall be manufactured from tempered rolled

46、 steel to the above specification with a tensile strength level of +C850 according to EN 10088-2 or hardness HV (300 25) according to EN 10151:2002. All stainless steel parts shall be edge dressed and free from sharp edges to prevent injury to the installer and damage to the rubber sleeve. The worm

47、drive units used for shear bands shall be of the same design and specification as those for the clamping bands. 4.2.2 Rubber 4.2.2.1 General Rubber used in coupling and adaptor bodies and bushes shall comply with EN 681-1. 4.2.2.2 Joining rubber sections Where it is necessary to join rubber sections

48、 this shall be using the vulcanisation process. DIN EN 16397-2:2015-01 EN 16397-2:2014 (E) 9 4.3 Product characteristics 4.3.1 Dimensional tolerances 4.3.1.1 General Only minimum dimensions are specified in Table 1 and Table 2. Manufacturers can use dimensions greater than these to suit the specific

49、 application. 4.3.1.2 Rubber components The tolerances on the manufactured dimensions of moulded and fabricated rubber components shall comply with ISO 3302-1:2014, Class M3. 4.3.1.3 Extruded rubber The tolerances on the manufactured dimensions of extruded rubber strip shall comply with ISO 3302-1:2014, Class E3. 4.3.1.4 Adaptors and Type 1 couplings Dimensions of rubber and metal components shall be in accordance with the manufacturers declared specifications. 4.3.1.5 Type 2 couplings Minimum dimensions of the rubber and