DIN EN 16593-2015 Packaging - Rigid plastic containers - PET finish BVS 30H60 German version EN 16593 2014《包装 硬质塑料容器 BVS 30H60聚酯涂层 德文版本EN 16593-2014》.pdf

1、January 2015 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、 55.100!%?DT“2283349www.din.deDDIN EN 16593Packaging Rigid plastic containers PET finish BVS 30H60;English version EN 16593:2014,English translation of DIN EN 16593:2015-01Verpackung Formstabile Kunststoffbehlter PET-Verschlussmundstck BVS 30H60;Englische Fassung EN 16593:2014,Englische bersetzung v

3、on DIN EN 16593:2015-01Emballage Rcipients en plastique rigide Bague PET BVS 30H60;Version anglaise EN 16593:2014,Traduction anglaise de DIN EN 16593:2015-01www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 14 pages 12.14 DIN EN 16593:201

4、5-01 2 A comma is used as the decimal marker. National foreword This document (EN 16593:2014) has been prepared by Technical Committee CEN/TC 261 “Packaging” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the DIN-Normenausschuss Verpackungswesen (DIN Standa

5、rds Committee Packaging), Working Committee NA 115-02-09 AA Behltnisse aus Kunststoff. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16593 October 2014 ICS 55.100 English Version Packaging - Rigid plastic containers - PET finish BVS 30H60 Emballage - Rcipients en plastique rigide - BaguePETBV

6、S 30H60 Verpackung - Formstabile Kunststoffbehlter - PET-Verschlussmundstck BVS 30H60 This European Standard was approved by CEN on 6 September 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status

7、of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, Germa

8、n). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia,

9、 Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and Unite

10、d Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1

11、6593:2014 EEN 16593:2014 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 5 2 Dimensions .5 3 Requirements .5 Bibliography . 12 DIN EN 16593:2015-01 EN 16593:2014 (E) 3 Foreword This document (EN 16593:2014) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of wh

12、ich is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2015, and conflicting national standards shall be withdrawn at the latest by April 2015. Attention is drawn to the possi

13、bility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries ar

14、e bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Po

15、rtugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DINEN 16593:2015-01EN 16593:2014 (E) 4 Introduction This European Standard is based on CE.T.I.E. (International Technical Centre for Bottling and Packaging) data sheet GME 30.27 (2010) 1. Efficient packag

16、ing is of great importance for the distribution and the protection of goods. Insufficient or inappropriate packaging can lead to damage or wastage of the contents of the pack. DIN EN 16593:2015-01 EN 16593:2014 (E) 5 1 Scope This European Standard specifies the design and dimensions of the screw PET

17、 finish BVS 30H60 for the closure of wines with CO2content below 1,2 grams per litre. This finish is designed to take an aluminium tamperevident closure with extended skirt which is reformed during application or a screw plastic closure (with or without metallic shell). 2 Dimensions The design and d

18、imensions of the finish shall be as shown in Figure 1 and Figure 2. Figure 3 shows an alternative construction of the neck. Figure 4 shows the run out of thread. These figures are showing dimensions for a blown bottle. 3 Requirements This finish is a top and side seal finish. For an optimum tightnes

19、s the surface in the sealing area shall be smooth and free of any defects. Flash in the sealing area is not allowed. Flash outside the sealing area may not be continuous and may not exceed 0,13 mm per side. A support ledge is necessary if the vertical load resistance of the bottle is below 120 daN.

20、DINEN 16593:2015-01EN 16593:2014 (E) 6 Dimensions in millimetres DIN EN 16593:2015-01 EN 16593:2014 (E) 7 Key 1 27,84 mm max on the length between 30 mm and 54,5 mm from the top of finish 2 Closure contact area 3 Thread run-in S Height from top of finish to start of full depth of thread P Thread pit

21、ch PL Parting line T Thread crest diameter E Thread root diameter Figure 1 - Design and dimension of the finish DIN EN 16593:2015-01 EN 16593:2014 (E) 8 Dimensions in millimetres Section A-A Figure 2a Figure 2b Key a Sealing surface b Sink marks are allowed in this area Figure 2 - Details of design

22、and dimension of the finish DINEN 16593:2015-01EN 16593:2014 (E) 9 Dimensions in millimetres Figure 3a DIN EN 16593:2015-01 EN 16593:2014(E)10 Section A-A Figure 3b Figure 3c Key a Sealing surface Figure 3 - Alternative construction of the neck DINEN 16593:2015-01EN 16593:2014(E)11 Figure 4 - Run ou

23、t of thread In Figure 4, Z-Z is the last full depth and width of thread. Beyond this point and Y-Y, the thread root should be increased gradually to full thread diameter T in 180 of turn. DINEN 16593:2015-01EN 16593:2014(E)12 Bibliography 1 CE. T.I.E. data sheet 30.27- PET finish BVS 30H60 -20101)1) Obtainable through Centre Technique International de lEmbouteillage et du Conditionnement (CE.T.I.E), 112- 114, rue La Botie, 75008 Paris, France, www.cetie.org, TP: 0033-1-42 65 26 45, TF: 0033-1-40 07 03 21. DINEN 16593:2015-01