DIN EN 22339-1992 Unhardened taper pins (ISO 2339 1986) german version EN 22339 1992《未淬火的锥形销》.pdf

1、UDC 621.886.114 DEUTSCHE NORM October 1992 I I I 7 1 7979 6325 7979 7977 7978 Unhardened taper pins (IS0 2339 : 1986) English version of DIN EN 22 339 I EN22339 Kegelstifte, ungehrtet (IS0 2339 : 1986) This standard incorporates the English version of Is0 2339. Supersedes DIN 1, September 1981 editi

2、on. European Standard EN 22 339 : 1992 has the status of a DIN Standard. A comma is used as the decimal marker. National foreword The publication of this standard is in keeping with a decision made by CEN/TC 185 to adopt, without alteration, a series of IS0 Standards covering parallel and taper pins

3、 as European Standards. The responsible German body involved in their publication is the Normenausschu Mechanische Verbindungselemente (Fasteners Standards Committee). As a consequence, all DIN Standards covering such pins have been superseded by the corresponding DIN EN Standards (see table below).

4、 EN Standard r DIN EN Standard Title Previous DIN Standard 22 338 22 339 28 733 28 734 28 735 28 736 28 737 22 338 22 339 28 733 28 734 28 735 28 736 28 737 Unhardened parallel pins Unhardened taper pins Unhardened parallel pins with internal thread Hardened parallel pins Hardened parallel pins with

5、 internal thread Unhardened taper pins with internal thread Unhardened taper pins with external thread See National appendix for guideline values for the mass of taper pins not given in the European Standard. The DIN Standards corresponding to the IS0 Standards referred to in clause 2 of the EN are

6、as follows: IS0 Standard DIN Standard IS0 2081 DIN 50 961 IS0 3269 The DIN 4000-9-1 tabular layout of article characteristics applies for pins as covered here. DIN IS0 3269 (at present at the stage draft) Continued overleaf. EN comprises 6 pages. Beuth Verlag GrnbH, Berlin, has the exclusive right o

7、f sale for German Standards (DIN-Normen). DIN EN 22 339 Engl. Price group 7 04.93 Sales No. 11 07 Page 2 DIN EN 22 339 Standards referred to (and not included in References) DIN 4000 Part 9 Tabular layout of article characteristics for bolts, screws, pins, rivets, keys, and lock washers DIN 50 961 C

8、hromating of zinc and cadmium coatings on iron and steel Previous ditions DIN 1: 03.18, 05.20, 02.25, 02.32, 07.36, 01.41, 01.43, 06.56, 03.61, 09.81; DIN 2: 03.18; DIN 92: 03.23, 10.36. Amendments In comparison with DIN 1, September 1981 edition, the following amendments have been made. a) The spec

9、ifications for the nominal lengths and their tolerances have been amended and new lengths introduced. b) The point length (dimension c) has been amended. c) The specifications for surface roughness have been amended. d) The material hardness has been specified. e) The standard designation has been c

10、hanged. International Patent Classification F 16 B 19/02 EUROPEAN STANDARD NORME EUROPENNE EUROPAISCHE NORM EN 22 339 July 1992 UDC 621.886.114 Descriptors: Fasteners, taper pins, dimensions, specifications, designation. English version Taper pins, unhardened (IS0 2339 : 1986) Goupilles de position

11、coniques, non trempes (IS0 2339 : 1986) Kegelstifte, ungehrtet (IS0 2339 : 1986) This European Standard was approved by CEN on 1992-07-17 and is identical to the IS0 Standard as referred to. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for g

12、iving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official ve

13、rsions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium

14、, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. GEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassar

15、t 36, 8-1050 Brussels O 1992. Copyright reserved to all CEN members. Ref. No. EN 22 339 : 1992 E Page 2 EN 22 339 : 1992 Foreword In 1992, CEN/TC 185 Threaded and unthreaded fasteners and accessories, the Secretariat of which is held by DIN, decided to submit International Standard IS0 2339 : 1986 T

16、aper pins, unhardened to Formal Vote. The result was positive. In the countries bound to implement this European Standard, a national standard identlcal to this European Standard shall be published, and conflicting national standards withdrawn, by 1993-01 -31 at the latest. In accordance with the CE

17、NKENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Endorsement notice The

18、 text of the International Standard IS0 2339 : 1986 was approved by CEN as a European Standard without any modifi- cation. Page 3 EN 22 339 : 1992 1 Scope and field of application This International Standard specifies the characteristics of unhardened taper pins, with metric dimensions and nominal d

19、iameters, d, from 0,6 to 50 mm inclusive. 2 References IS0 2081, MetaUic coatings - Ehctroplated coatings of zinc on iron or steef. IS0 3269, Fasteners - Acceptance inspection. IS0 4520, Chmmte conversion coatings on electroplated zinc and cadmium coatings. Page 4 EN 22 339 : 1992 3 Dimensions Type

20、A (ground pins) : Surface finish Ra = 0,8 pm Type B (turned pins) : Surface finish Ra = 3,2 pm Dimensions in millimetres 1 ) Other tderancee, for example, al 1, cl 1,B. as agreed between customer and supplier. 2) For nominal lengths above 200 mm, steps of 20 mm. Page 5 EN 22 339 : 1992 4 Specificati

21、ons and reference International Standards Material Suriacm nish Workmanship - Acceptability St = Free-cuttingsteel, Other materiais as agreed between customer and supplier. hardness 125 to 245 HV. Plain, .e. pins to be supplied in natural finish treated with a rust-preventative lubricant, unless oth

22、erwise specified by agreement between customer and supplier. Preferred coetings are black oxide, phosphate coating or zinc plating with chromate conversion coating (see IS0 2081 end IS0 45i. Other coatings as agreed between customer and supplier. All tolsrances shall apply prior to the application o

23、f a plating or coating. Parts shall be uniform in quality and free of irregularities or detrimental defects. No burm shall appear on any part of the pin. The taper shall be inspected by use of an adequate optical comparator. The acceptance procedure is covered in IS0 326!3. 5 Designation Example for

24、 the designation of an unhardened steel taper pin, ype A, with nominal diameter d= 6 mm and nominal length I= 3mm: Taper pin IS0 p39 - A - 6 x 30 - St Page 6 EN 22 339 : 1992 National appendix (informative) Mass of taper pins The values given are guideline values. O$ O# 1 1,2 13 2 25 3 4 5 6 8 10 12 16 20 25 30 40 50 Approximate mass (7,85 kg/dm3), in kg per 1 O00 units