DIN EN ISO 11126-8-1997 Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 8 Olivin.pdf

1、DEUTSCHE NORM November 1997 Specifications for non-metallic blast-cleaning abrasives Part 8: Olivine sand (IS0 11 126-8 : 1993) English version of DIN EN IS0 11 126-8 DIN - EN IS0 11126-8 ICs 25.220.1 O Descriptors: Abrasives, blast-cleaning. Vorbereitung von Stahloberflchen vor dem Auftragen von Be

2、schichtungsstoffen - Anforderungen an nichtmetallische Strahlmittel -Teil 8: Olivinsand (IS0 11 126-8 : 1993) European Standard EN IS0 11 126-8 : 1997 has the status of a DIN Standard. A comma is used as the decimal marker. National foreword This standard has been published in accordance with a deci

3、sion taken by CEN/TC 139 to adopt, without alteration, International Standard IS0 11 126-8 as a European Standard. The responsible German body involved in its preparation was the Normenausschu Anstrichstoffe und ahnliche Beschichtungsstoffe (Paints and Varnishes Standards Committee), Technical Commi

4、ttee Strahlmittel. The DIN Standards corresponding to the International Standards referred to in clause 2 of the EN are as follows: IS0 Standard DIN Standard IS0 11 127-1 IS0 11 127-2 IS0 11 127-3 IS0 11 127-4 IS0 11 127-5 IS0 11 127-6 IS0 11 127-7 DIN EN IS0 11 127-1 DIN EN IS0 11 127-2 DIN EN IS0

5、11 127-3 DIN EN IS0 11 127-4 DIN EN IS0 11 127-5 DIN EN IS0 11 127-6 DIN EN IS0 11 127-7 National Annex NA Standards referred to (and not included in Normative references and Annex ZA) DIN EN IS0 11 127-1 Test methods for non-metallic blast-cleaning abrasives - Part 1 : Sampling DIN EN IS0 11 127-2

6、Test methodsfor non-metallic blast-cleaning abrasives - Part 2: Determination of particle size distribution (IS0 11 127-2 : 1993) DIN EN IS0 11 127-3 Test methodsfor non-metallic blast-cleaning abrasives - Part 3: Determination of (IS0 11 127-1 : 1993) DIN EN IS0 DIN EN IS0 DIN EN IS0 DIN EN IS0 app

7、arent density (IS0 1 11 27-3 : 1993) Test methods for non-metallic blast-cleaning abrasives - Part 4: Determination of hardness by glass slide test (IS0 11 127-4 : 1993) Test methods for non-metallic blast-cleaning abrasives - Part 5: Determination of moisture (IS0 1 1 127-5 : 1993) Test methods for

8、 non-metallic blast-cleaning abrasives - Part 6: Determination of water-soluble contaminants (IS0 11 127-6 : 1993) Test methods for non-metallic blast-cleaning abrasives - Part 7: Determination of water-soluble chlorides (IS0 11 127-7 : 1993) 11 27-4 11 27-5 11 27-6 11 27-7 EN comprises 7 pages. No

9、pari of this standard may be reproduced without the prior permission of Ref. No. DIN EN IS0 11 126-8 : 1997-1 Y Deutsches Institut fr Normung e. V., Berlin. wth Verlag GmbH, D-10772 Berlin, has the exclusive right of sale for German Standards (DIN-Normen). English price group O7 Sales No. 1107 04.98

10、 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 11 126-8 July 1997 ICs 87.020 Descriptors: Abrasives, blast-cleaning. English version Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning a brasives Part 8: Olivine

11、sand (IS0 1 1 126-8 : 1993) Prparation dessubjectilesdacieravant Vorbereitung von Stahloberflchen vor application de peintures et de produits dem Auftragen von Beschichtungs- assimils - Spcifications pour abrasifs stoffen - Anforderungen an nichtmetal- nonmtalliquesdestins la prparation lische Strah

12、lmittel - Teil 8: Olivinsand par projection -Partie 8: Sable lolivine (IS0 1 11 26-8 : 1993) (IS0 11 126-8 : 1993) This European Standard was approved by CEN on 1997-06-1 6. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this Europe

13、an Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stand- ards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three official versions (English,

14、 French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, the Czech Repu

15、blic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: r

16、ue de Stassart 36, B-1050 Brussels O 1997. CEN - All rights of exploitation in any form and by any means reserved worldwide for CEN national members. Ref. No. EN IS0 11 126-8 : 1997 E Page 2 EN IS0 11 126-8 : 1997 Foreword International Standard IS0 1 1 126-8 : 1993 Preparation of steel substrates b

17、efore application of paints and related products - Speci- fications for non-metallic blast-cleaning abrasives - Part 8: Olivine sand, which was prepared by ISO/TC 35 Paints and varnishes of the International Organization for Standardization, has been adopted by Technical Committee CEN/TC 139 Paints

18、and varnishes, the Secretariat of which is held by DIN, as a European Standard. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, and conflicting national standards withdrawn, by January 1998 at the latest. In accor

19、dance with the CENKENELEC Internal Regulations, the national standards organizations of the follow- ing countries are bound to implement this European Standard: Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norw

20、ay, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. Endorsement notice The text of the International Standard IS0 11 126-8 : 1993 was approved by CEN as a European Standard without any modification. NOTE: Normative references to international publications are listed in Annex ZA (normat

21、ive). WARNING - Equipment, materials and abrasives used for surface preparation can be hazardous if used carelessly. Many national regulations exist for those materials and abrasives that are considered to be hazardous during or after use (waste management), such as free silica or carcinogenic or to

22、xic substances. These regulations are therefore to be observed. It is important to ensure that adequate instructions are given and that all required precautions are exercised. 1 Scope This part of IS0 11 126 specifies requirements for olivine sand abrasives, as supplied for blast-cleaning processes.

23、 It specifies ranges of particle sizes and values for apparent density, Mohs hardness, moisture content, conductivity of aqueous extract and water- soluble chlorides. The requirements specified in this part of IS0 11 126 apply to abrasives supplied in the “new“ condition only. They do not apply to a

24、brasives either during or after use. Test methods for non-metallic blast-cleaning abrasives are given in the various parts of IS0 11127. NOTES 1 for non-metallic abrasives is given in annex A. Information on commonly referenced national standards niques are described in IS0 8504-2:1992, Preparation

25、of steel substrates before application of paints and related products - Surface preparation methods - Part 2: Abras- ive blast-cleaning. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of IS0 11 126. At the t

26、ime of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of IS0 11 126 are encouraged to investi- gate the possibility of applying the most recent edi- tions of the standards indicated below. Members of IEC and IS0 mai

27、ntain registers of currently valid International Standards. IS0 11 127-1 :I 993, Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 1: Sampling. 2 Although this part of IS0 11126 has been developed specifi

28、cally to meet requirements for preparation of steelwork, the properties specified will generally be appro- priate for use when preparing other material surfaces, or components, using blastcleaning techniques. These tech- IS0 1 1 127-211 993, Preparation of steel substrates before application of Pain

29、ts and related products - Test methods for non-metallic blast-cleaning abrasives - Part 2: Determination of particle size distribution. Page 3 EN IS0 11 126-8 : 1997 IS0 1 1 127-3:1993, Preparation of steel substrates before application of paints and related products - Test methods for non-metallic

30、blast-cleaning abrasives - Pari 3: Determination of apparent density. IS0 1 1 1274: 1993, Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blastcleaning abrasives - Part 4: Assessment of hardness by a glass slide test. IS0 11 127-5:199

31、3, Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blastcleaning abrasives - Part 5: Determination of moisture. IS0 1 1 127-6:1993, Preparation of steel substrates before application of paints and related products - Test methods for n

32、on-metallic blastcleaning abrasives - Part 6: Determination of water-soluble contami- nants by conductivity measurement. IS0 1 I1 27-7:1993, Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blastcleaning abrasives - Part 7: Determinati

33、on of water-soluble chlorides. 3 Definition For the purposes of this part of IS0 11 126, the fol- lowing definition applies. 3.1 olivine sand: A material manufactured from the naturally occurring mineral olivine which is crushed by a mechanical process, dried and sieved and prepared for use as a bla

34、st-cleaning abrasive. NOTE 3 chemical formula MgO.SiO,.Fe,O,. Olivine is a magnesium/iron silicate with the 4 Designation of abrasives Olivine sand abrasives shall be identified by ”Abrasive IS0 11 126” and the abbreviation N/OL indicating non-metallic, olivine sand abrasive. This shall be fol- lowe

35、d, without spaces, by an oblique stroke and then by the symbol G to indicate the required particle shape of the abrasive, when purchased, as grit. The designation shall be completed by numbers denoting the particle size range, in millimetres, required (see table 1). EXAMPLE 1 Abrasive IS0 11 126 N/O

36、L/G 0.2-03 denotes an abrasive of the non-metallic olivine sand type, complying with the requirements of this part of IS0 11 126, of initiai particle shape grit and particle size range 0,2 mm to 0,5 mm. It is essential that this full product designation is quoted on all orders. 5 Sampling Sampling p

37、rocedures shall be as specified in IS0 11127-1. 6 Requirements 6.1 General requirements The material shall be free from corrosive constituents and adhesion-impairing contaminants. Foreign, harm- ful impurities shall not be permitted. 6.2 Particular requirements Particular requirements for olivine sa

38、nd abrasives shall be as specified in table 2. 7 Identification and marking All supplies shall be clearly marked or identified using the appropriate designation as specified in clause 4, either directly or by the accompanying delivery note. 8 Information to be supplied by the manufacturer or supplie

39、r The manufacturer or supplier shall supply, if re- quested, a test report detailing results for any relevant property as determined by the appropriate method specified in table 2. Page 4 EN IS0 11 126-8 : 1997 kglm3 Ckg/dm31 Apparent density Table 1 - Particle size distribution IS0 11 127-3 (3.0 to

40、 3,3) x 103 c3.0 to 3,3 1) By agreement between the interested parties, abrasives of different particle size ranges may be mixed together. Details of proportions of nominal size, oversize and undersize shall be specified. The maximum particle size shall not exceed 3.1 5 mm and the proportion of part

41、icles less than 0,2 mm shall not exceed 5 % (dm). Mohs hardness) Moisture 40 dm) Conductivity of aqueous extract mS/m Water-soluble chlorides 40 (dm) Table 2 - Particular requirements for olivine sand abrasives min. 6 IS0 11 127-4 max. 0.2 IS0 11 127-5 max. 25 IS0 11 127-6 max. 0,002 5 IS0 11 127-7

42、Property I Requirement I Test method I Particle size range and distribution I See table1 I IS0 11 127-2 I Page 5 EN ISO11126-8: 1997 Annex A (i n f or ma t ive) Bibliography Commonly referenced national standards for non- 3 DIN 8201 Teil 5:1985, Feste Strahlmittel, metallic abrasives are as follows:

43、 natrlich, mineralisch; Quarzsand (Natural min- eral abrasives; quartz sand). I DIN 8200:1982, Strahlverfahrenstechnik; Begriffe, Einordnung der Strahlverfahren (Blast- 4 DIN 8201 Teil 6:1985, Feste Strahlmittel, ing; terms, classification of blasting synthetisch, mineralisch; Elektrokorund (Syn- te

44、chniques). thetic mineral abrasives; electric corundum). 2 DIN 8201 Teil 1:1985, feste Strahlmittel; 5 DIN 8201 Teil 9:1986, Feste Strahlmittel, Einteilung, Bezeichnung (Abrasives; classifica- synthetisch, mineralisch; Kupferhttenschlacke, tion, designation). Schrnelzkammerschlacke (Synthetic minera

45、l solid abrasives; copper refinery slag, melting chamber slag). Page 6 EN IS0 11 126-8 : 1997 Annex ZA (normative) Normative references to international publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other pub

46、lications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revis

47、ion. For undated references the latest edition of the publication referred to applies. Publication Year IS0 11 127-1 1993 IS0 11 127-2 1993 IS0 11 127-3 1993 IS0 11 127-4 1993 IS0 11 127-5 1993 - EN Preparation of steel substrates EN IS0 11 127-1 1997 before application of paints and related product

48、s - Test methods for non-metallic blast-cleaning abrasives - Part 1 : Sampling Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 2: Determination of particle size distribution Preparation of steel substra

49、tes before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 3: Determination of apparent density Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 4: Assessment of hardness by a glass slide test Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 5: Determination of moisture EN IS0 11 127-2 1997 EN IS0 11 127-3