DIN EN ISO 11151-2-2015 Lasers and laser-related equipment - Standard optical components - Part 2 Components for the infrared spectral range (ISO 11151-2 2015) German version EN IS.pdf

1、December 2015 English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 31.260!%I(English version EN IS

2、O 11151-2:2015,English translation of DIN EN ISO 11151-2:2015-12Laser und Laseranlagen Optische Standardkomponenten Teil 2: Komponenten fr den infraroten Spektralbereich (ISO 11151-2:2015);Englische Fassung EN ISO 11151-2:2015,Englische bersetzung von DIN EN ISO 11151-2:2015-12Lasers et quipements a

3、ssocis aux lasers Composants optiques standards Partie 2: Composants pour la plage spectrale infrarouge (ISO 11151-2:2015);Version anglaise EN ISO 11151-2:2015,Traduction anglaise de DIN EN ISO 11151-2:2015-12SupersedesDIN EN ISO 11151-2:2000-11www.beuth.deDocument comprises 18 pagesDTranslation by

4、DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.11.15 DIN EN ISO 11151-2:2015-12 2 A comma is used as the decimal marker. National foreword This document (EN ISO 11151-2:2015) has been prepared by Technical Committee ISO/TC 172/SC 9 “Electro-optica

5、l systems” in collaboration with Technical Committee CEN/TC 123 “Lasers and photonics” (both secretariats are held by DIN, Germany). The responsible German body involved in its preparation was DIN-Normenausschuss Feinmechanik und Optik (DIN Standards Committee Optics and Precision Mechanics), Workin

6、g Committee NA 027-01-18 AA Laser. Part 1: Components for the UV, visible and near-infrared spectral ranges Part 2: Components for the infrared spectral range In addition to the legal units of measurement, this standard also uses the unit “inch”. It should be noted that the Gesetz ber Einheiten im M

7、esswesen (German Law on units in metrology) prohibits the use of this unit for official and commercial purposes in Germany. The indication of this unit solely serves to facilitate the communication with those countries where this unit is used (import-export business). Conversion: Unit not permitted

8、Unit permitted Conversion in (inch) mm 1 inch = 25,4 mm The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 9211-1 DIN ISO 9211-1 ISO 9211-2 DIN ISO 9211-2 ISO 10110-1 DIN ISO 10110-1 ISO 10110-2 DIN ISO 10110-2 ISO 10110-3 DIN ISO 10110-3

9、ISO 10110-4 DIN ISO 10110-4 ISO 10110-5 DIN ISO 10110-5 ISO 10110-6 DIN ISO 10110-6 ISO 10110-7 DIN ISO 10110-7 The code letters used in Table 1 to denote the component forms have been chosen on the basis of the English terms. DIN EN ISO 11151 consists of the following parts, under the general title

10、 Lasers and laser-related equipment _- Standard optical components: DIN EN ISO 11151-2:2015-12 3 Amendments This standard differs from DIN EN ISO 11151-2:2000-11 as follows: a) the scope has been amended to include the near-infrared to mid-infrared spectral ranges from 2,1 m to 15,0 m; b) the range

11、of materials to be used has been extended to include calcium fluoride and sapphire; gallium arsenide has been dropped; c) In Tables 5 and 6, footnotes have been added; d) normative references have been updated. Previous editions DIN EN ISO 11151-2: 2000-11 DIN EN ISO 11151-2:2015-12 4 National Annex

12、 NA (informative) Bibliography DIN ISO 9211-1, Optics and photonics Optical coatings Part 1: Terms and definitions DIN ISO 9211-2, Optics and photonics Optical coatings Part 2: Optical properties DIN ISO 10110-1, Optics and photonics Preparation of drawings for optical elements and systems Part 1: G

13、eneral DIN ISO 10110-2, Optics and optical instruments Preparation of drawings for optical elements and systems Part 2: Material imperfections; stress birefringence DIN ISO 10110-3, Optics and optical instruments Preparation of drawings for optical elements and systems Part 3: Material imperfections

14、 bubbles and inclusions DIN ISO 10110-4, Optics and optical instruments Preparation of drawings for optical elements and systems Part 4: Material imperfections; inhomogenity and striae DIN ISO 10110-5, Optics and photonics Preparation of drawings for optical elements and systems Part 5: Surface for

15、m tolerances DIN ISO 10110-6, Optics and optical instruments Preparation of drawings for optical elements and systems Part 6: Centring tolerances DIN ISO 10110-7, Optics and photonics Preparation of drawings for optical elements and systems Part 7: Surface imperfection tolerances DIN ISO 14997, Opti

16、cs and photonics Test methods for surface imperfections of optical elements EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 11151-2 July 2015 ICS 31.260 Supersedes EN ISO 11151-2:2000 English Version Lasers and laser-related equipment - Standard optical components - Part 2: Components for t

17、he infrared spectral range (ISO 11151-2:2015) Lasers et quipements associs aux lasers - Composants optiques standards - Partie 2: Composants pour la plage spectrale infrarouge (ISO 11151-2:2015) Laser und Laseranlagen - Optische Standardkomponenten - Teil 2: Komponenten fr den infraroten Spektralber

18、eich (ISO 11151-2:2015) This European Standard was approved by CEN on 21 February 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date list

19、s and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under

20、the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yug

21、oslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T EU

22、R O P EN D E NOR M A L I S ATI O N EUR O P I S C HES KOM I T E E F R NOR M UNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 11151-2:2015 E European forewo

23、rd .3Introduction 41 Scope . 52 Normative references 53 Code for components covered 64 Materials . 65 Requirements for quality 76 Dimensional tolerances 96.1 Preferred dimensions 96.2 Diameter of circular optical components. 96.3 Mirror and output coupler curvature 96.4 Rectangular and elliptical wi

24、ndows . 96.5 Focal length 96.6 Thickness 107 Testing area . 108 Designation for ordering 109 Coating . 1210 Packaging 12Annex A (informative) Imperial units 13Bibliography .14Contents PageDIN EN ISO 11151-2:2015-12 EN ISO 11151-2:2015 (E) 2 European foreword This document (EN ISO 11151-2:2015) has b

25、een prepared by Technical Committee ISO/TC 172 “Optics and photonics” in collaboration with Technical Committee CEN/TC 123 “Lasers and photonics” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical te

26、xt or by endorsement, at the latest by January 2016, and conflicting national standards shall be withdrawn at the latest by January 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held respons

27、ible for identifying any or all such patent rights. This document supersedes EN ISO 11151-2:2000. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyp

28、rus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the Unite

29、d Kingdom. Endorsement notice The text of ISO 11151-2:2015 has been approved by CEN as EN ISO 11151-2:2015 without any modification. DIN EN ISO 11151-2:2015-12 EN ISO 11151-2:2015 (E) 3 IntroductionLasers are used in a wide variety of applications, including medicine, materials processing, informati

30、on technology, and metrology. Most lasers contain optical windows and mirrors (intracavity) and most laser systems use a variety of windows, beam splitters, deflectors, mirrors, and lenses. Those components used in high-power laser applications must withstand high-peak power and/or energy densities

31、to avoid laser-induced damage, thus their component specifications are more demanding than those used in low-power applications.DIN EN ISO 11151-2:2015-12 EN ISO 11151-2:2015 (E) 4 1 ScopeThis part of ISO 11151 specifies requirements for laser components used from near-infrared to mid-infrared, from

32、 wavelengths 2,1 m to 15,0 m, and facilitates the supply of spare parts by specifying preferred dimensions and tolerances, thereby reducing the variety of types, by standardizing the specifications and removing barriers to trade, and by establishing an agreed designation for item orders.This part of

33、 ISO 11151 covers planar, plano-spherical, and spherical substrates, lenses, and optical components that are designed specifically as standardized optical components normally offered through a catalogue from suppliers and intended for use with lasers.This part of ISO 11151 includes component descrip

34、tions, materials employed, physical dimensions, and manufacturing tolerances (including surface finish, figure, and parallelism). Although most, but not all of these components will be coated (fully reflecting, partially reflecting, or anti-reflecting) before incorporation into the laser system, thi

35、s part of ISO 11151 does not include recommendations for the specification of coatings.NOTE The optical components used in the ultraviolet, visible, and near infrared spectral ranges (170 nm to 2 100 nm) is referred to ISO 11151-1. The specification and testing of optical coatings is referred to ISO

36、 9211 (all parts).2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (in

37、cluding any amendments) applies.ISO 9211-1, Optics and photonics Optical coatings Part 1: DefinitionsISO 9211-2, Optics and photonics Optical coatings Part 2: Optical propertiesISO 10110-1:2006, Optics and photonics Preparation of drawings for optical elements and systems Part 1: GeneralISO 10110-2,

38、 Optics and optical instruments Preparation of drawings for optical elements and systems Part 2: Material imperfections Stress birefringenceISO 10110-3, Optics and optical instruments Preparation of drawings for optical elements and systems Part 3: Material imperfections Bubbles and inclusionsISO 10

39、110-4, Optics and optical instruments Preparation of drawings for optical elements and systems Part 4: Material imperfections Inhomogeneity and striaeDIN EN ISO 11151-2:2015-12 EN ISO 11151-2:2015 (E) 5 ISO 10110-51), Optics and photonics Preparation of drawings for optical elements and systems Part

40、 5: Surface form tolerancesISO 10110-61), Optics and photonics Preparation of drawings for optical elements and systems Part 6: Centring tolerancesISO 10110-7, Optics and photonics Preparation of drawings for optical elements and systems Part 7: Surface imperfection tolerances3 Code for components c

41、overedTable 1 specifies codes for the components to which this part of ISO 11151 is applicable.Table 1 Component codesComponent form CodeOptical flats IOFCircular windows flat IWCElliptical windows flat IWERectangular windows flat IWROutput couplers flat IOCMirrors flat IMFMirrors convex IMXMirrors

42、concave IMVPlano-convex lenses IPXPlano-concave lenses IPVSymmetric biconvex lenses IBXSymmetric biconcave lenses IBV4 MaterialsThis part of ISO 11151 covers components employed in the infrared wavelength region from 2,1 m to 15 m. A wide range of materials may be used, such as zinc selenide, ZnSe,

43、potassium chloride, KCl, germanium, Ge, calcium fluoride, CaF2, silicon, Si, copper, Cu, and Sapphire, Al2O3.In view of the wide variety of materials available, the use of specific code numbers for each material has not been formalized. Manufacturers and designers shall therefore specify the exact m

44、aterials used/required. The material specification shall be given as stated in ISO 10110-1:2006, 4.7. If birefringent materials are used/specified, the orientation of the optical axis relative to the geometric axes of the components shall be stated.1) Currently under revision.DIN EN ISO 11151-2:2015

45、12 EN ISO 11151-2:2015 (E) 6 5 Requirements for qualityPreferred specifications and classes for material and surface quality are set out in Tables 2 to 6, using terminology in accordance with ISO 10110-1 to ISO 10110-7. The same quality standards apply to all components of a given diameter, except

46、that the material tolerances are inapplicable in the case of total reflector substrates.The requirement of quality for components to be used with infrared lasers is in general high; therefore this part of ISO 11151 only promulgates one class of quality.NOTE The quoted grade values assume that most o

47、f the incident radiation is scattered out of the beam by the imperfection. This is the case where the radiometric obscuration equals the area obscuration. If the imperfection is partially transmitting, its actual area could be larger than is suggested by these values. A method for measuring the surface imperfections is described in ISO 14997.For this reason, there is no difference between a flat circular window, IWC, specification and an output coupler, IOC, specification in this waveband. It should be noted that the s