DIN EN ISO 11833-2-2006 Plastics - Unplasticized poly(vinyl chloride) sheets - Types dimensions and characteristics - Part 2 Sheets of thickness less than 1mm (ISO 11833-2 1998) E.pdf

1、 DEUTSCHE NORMJune 2006DIN EN ISO 11833-2 ICS 83.140.10 Plastics Unplasticized poly(vinyl chloride) sheets Types, dimensions and characteristics Part 2 : Sheets of thickness less than 1 mm (ISO 11833-2:1998) English version of DIN EN ISO 11833-2:2006-06 Kunststoffe Weichmacherfreie Polyvinylchloridt

2、afeln Typen, Mae und Eigenschaften Teil 2: Tafeln mit einer geringeren Dicke als 1 mm (ISO 11833-2:1998) Englische Fassung DIN EN ISO 11833-2:2006-06 Document comprises 9 pages No part of this standard may be reproduced without prior permission of DIN Deutsches Institut fr Normung e. V., Berlin. Beu

3、th Verlag GmbH, 10772 Berlin, Germany, has the exclusive right of sale for German Standards (DIN-Normen). English price group 7 www.din.de www.beuth.de !,o4m“11.06 9761774DIN EN ISO 11833-2:2006-06 2 National foreword This standard has been published in accordance with a decision taken by CEN/TC 249

4、 to adopt, without alteration, International Standard ISO 11833-2 as a European Standard. The responsible German body involved in its preparation was the Normenausschuss Kunststoffe (Plastics Standards Committee), Technical Committee NA 054-04-02 AA Halbzeuge aus Thermoplasten. EN ISO 11833 consists

5、 of the following parts, under the general title Plastics Unplasticized poly(vinyl chloride) sheets Types, dimensions and characteristics: Part 1: Sheets of thickness not less than 1 mm Part 2: Sheets of thickness less than 1 mm The DIN Standards corresponding to the International Standards referred

6、 to in clause 2 of the EN are as follows: ISO 75-2 DIN EN ISO 75-2 ISO 291 DIN EN ISO 291 ISO 306 DIN EN ISO 306 ISO 527-3 DIN EN ISO 527-3 ISO 1163-1 DIN EN ISO 1163-1 ISO 2818 DIN EN ISO 2818 ISO 2859-1 DIN ISO 2859-1 ISO 8256 DIN EN ISO 8256 ISO 11501 DIN EN ISO 11501 National Annex NA (informati

7、ve) Bibliography DIN EN ISO 75-2, Plastics Determination of temperature of deflection under load Part 2: Plastics and ebonite DIN EN ISO 291, Plastics Standard atmospheres for conditioning and testing DIN EN ISO 306, Plastics Thermoplastic materials Determination of Vicat softening temperature (VST)

8、 DIN EN ISO 527-3, Plastics Determination of tensile properties Part 3: Test conditions for films and sheets DIN EN ISO 1163-1, Plastics Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials Part 1: Designation system and basis for specifications DIN EN ISO 2818, Plastics Prepa

9、ration of test specimens by machining DIN EN ISO 8256, Plastics Determination of the tensile-impact strength of plastics DIN EN ISO 11501, Plastics Film and sheeting Determination of dimensional change on heating DIN ISO 2859-1, Sampling procedures for inspection by attributes Part 1: Sampling plans

10、 indexed by acceptable quality level (AQL) for lot-by-lot inspection EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 11833-2 April 2006 ICS 83.140.10 English Version Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 2: Sheets of thickness le

11、ss than 1 mm (ISO 11833-2:1998) Plastiques - Feuilles en poly(chlorure de vinyle) non plastifi - Types, dimensions et caractristiques - Partie 2: Feuilles et films dpaisseur infrieure 1 mm (ISO 11833-2:1998) Kunststoffe - Weichmacherfreie Polyvinylchloridtafeln - Typen, Mae und Eigenschaften - Teil

12、2: Tafeln mit einer geringeren Dicke als 1 mm (ISO 11833-2:1998) This European Standard was approved by CEN on 16 March 2006. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard w

13、ithout any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other languag

14、e made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Ger

15、many, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUN

16、G Management Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 11833-2:2006: EForeword The text of ISO 11833-2:1998 has been prepared by Technical Committee ISO/TC 61 “Plastics” of

17、 the International Organization for Standardization (ISO) and has been taken over as EN ISO 11833-2:2006 by Technical Committee CEN/TC 249 “Plastics“, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identic

18、al text or by endorsement, at the latest by October 2006, and conflicting national standards shall be withdrawn at the latest by October 2006. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Stand

19、ard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Endorsement no

20、tice The text of ISO 11833-2:1998 has been approved by CEN as EN ISO 11833-2:2006 without any modifications. EN ISO 11833-2:2006 (E)21 Scope1.1 This part of ISO 11833 specifies requirements for sheets and films of unplasticized poly(vinyl chloride)(PVC-U) and the test methods to be used to measure t

21、he required values.1.2 It applies only to sheets of thickness less than 1,0 mm.1.3 It does not cover thermoshrinkable or biaxially stretched PVC-U sheets and films.2 Normative referencesThe following standards contain provisions which, through reference in this text, constitute provisions of this pa

22、rt ofISO 11833. At the time of publication, the editions indicated were valid. All standards are subject to revision, andparties to agreements based on this part of ISO 11833 are encouraged to investigate the possibility of applying themost recent editions of the standards indicated below. Members o

23、f IEC and ISO maintain registers of currently validInternational Standards.ISO 75-2:1993, Plastics Determination of temperature of deflection under load Part 2: Plastics and ebonite.ISO 291:1997, Plastics Standard atmospheres for conditioning and testing.ISO 306:1994, Plastics Thermoplastic material

24、s Determination of Vicat softening temperature (VST).ISO 527-3:1995, Plastics Determination of tensile properties Part 3: Test conditions for films and sheets.ISO 1163-1:1995, Plastics Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials Part 1:Designation system and basis for

25、 specifications.ISO 2818:1994, Plastics Preparation of test specimens by machining.ISO 2859-1:1), Sampling procedures for inspection by attributes Part 1: Sampling plans indexed by acceptablequality level (AQL) for lot-by-lot inspection.ISO 8256:1990, Plastics Determination of tensile-impact strengt

26、h.ISO 11501:1995, Plastics Film and sheeting Determination of dimensional change on heating.1) To be published. (Revision of ISO 2859-1:1989)EN ISO 11833-2:2006 (E)33 MaterialSheets shall be fabricated from unplasticized PVC compounds as defined in ISO 1163-1:1995, subclause 1.3.Compounds may contai

27、n additives such as stabilizers, lubricants, processing aids, impact modifiers, flameretardants and colourants. Compounds and additives of unknown identity and composition shall not be used for theprocessing of sheets.NOTE Legal considerations may cause a specific choice of compound.4 Classification

28、Sheets are classified into four groups (three of which are subdivided into two classes) by the numerical values ofthe two most important properties, i.e. the tensile impact strength and the Vicat softening temperature (see table 3).5 Requirements5.1 AppearanceThe surface shall be free of noticeable

29、flaws, cracks, mottling, voids, bubbles, impurities and other defects whichare not acceptable for the application envisaged. The sheet shall have a smooth surface, except for embossedsheets which shall have a uniform pattern. Any further requirements concerning appearance shall be agreedbetween the

30、interested parties.5.2 ColourColourants shall be distributed uniformly throughout the material. Admissible differences in colour within a sheet andamongst sheets shall be agreed between the interested parties as required.5.3 Dimensions5.3.1 Length, width and rectangularityThe length and width of she

31、ets shall be agreed between the interested parties. The tolerances on the dimensionsand the rectangularity shall be as specified in table 1.Table 1 Tolerances on length, width and rectangularityDimensions in millimetresDimension/rectangularity ToleranceLength Flat sheet+ 200Rolled sheet Minus not ac

32、ceptedWidth+ 50Rectangularity Flat sheet Dl 40 40 40 40 40 40 40 6.4.1Nominal strainat breakISO 527-3Type 1B50 mm/min% 20 20 20 20 20 20 20 6.4.1Tensile impactstrengthISO 8256Method AType 3kJ/m2 300 300 400 400 6.4.2VicatsofteningtemperatureISO 306Method B C 60 70 60 70 60 70 90 6.5The requirements

33、for the optional properties given in table 4 shall be agreed between the interested parties asrequired.Table 4 Optional propertiesProperty Test method UnitTemperature of deflection under load ISO 75-2Method ACDimensional change on heating ISO 11501 %EN ISO 11833-2:2006 (E)55.5 Chemical and physiolog

34、ical properties5.5.1 FlammabilityRequirements for flammability shall be agreed between the interested parties as required. Relevant national andinternational standards shall be considered in the agreement.5.5.2 Chemical resistanceRequirements for chemical resistance for specific applications shall b

35、e agreed between the interested parties asrequired.5.5.3 Physiological behaviourRequirements for physiological behaviour shall be agreed between the interested parties as required. The relevantlegislation shall be taken into consideration if the sheet will come into contact with food.6 Test methods6

36、.1 General6.1.1 SamplingTake a sample sufficient to determine the compliance of the material with this specification. The sampling proceduregiven in ISO 2859-1 is recommended.6.1.2 Preparation of specimensPrepare all specimens in accordance with ISO 2818. Prepare the specimens for tensile strength,

37、tensile impactstrength and dimensional change on heating by stamping or cutting. The surface of the specimens shall be free ofany damage or faults in order to avoid notch effects. Should any burrs be present on a specimen, remove themwithout damaging the surface.6.1.3 Conditioning and testing of spe

38、cimensUnless otherwise specified in the applicable test method, carry out testing in one of the standard atmospheresspecified in ISO 291, after conditioning the specimens for at least 16 h in the same atmosphere.6.2 Appearance examinationExamine the surfaces and cut edges with the naked eye from a d

39、istance of 60 cm for noticeable flaws, cracks,mottling, voids, bubbles, impurities and other defects, inspecting the sheet in the direction opposite to that of theincident light.6.3 Dimensions6.3.1 Measure the length, width and diagonals of the sheet to the nearest 1 mm, using a calibrated ruler.6.3

40、.2 Measure the thickness to the nearest 0,01 mm, using a calibrated thickness gauge.EN ISO 11833-2:2006 (E)66.3.3 RectangularityDetermine the rectangularity l as shown in figure 1.Dimensions in millimetresFigure 1 Rectangularity6.4 Mechanical properties6.4.1 Tensile stress at yield and nominal strai

41、n at breakDetermine the tensile stress at yield and the nominal strain at break in accordance with ISO 527-3, using at leastfive type 1B specimens for each direction and a test speed of 50 mm/min.6.4.2 Tensile impact strengthDetermine the tensile impact strength in accordance with ISO 8256.6.5 Vicat

42、 softening temperatureDetermine the Vicat softening temperature in accordance with ISO 306, Method B.7 MarkingThe following information shall be marked on each package of sheets:a) the number of this part of ISO 11833, the material and the product designation as shown below:b) the dimensions;c) the manufacturers name and country, and the year and month of manufacture or lot number.EN ISO 11833-2:2006 (E)7