DIN EN ISO 11997-2-2013 Paints and varnishes - Determination of resistance to cyclic corrosion conditions - Part 2 Wet (salt fog) dry humidity UV light (ISO 11997-2 2013) German ve.pdf

1、December 2013Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 87.040!%*zZ“2078755www.din.deDDIN EN ISO 11997-2Paints and varnishes Determination of resistance to cyclic corrosion conditions Part 2: Wet (salt fog)/dry/humidity/UV light (ISO 11997-2:2013);English version EN ISO 11997-2:2013,English translation of DIN EN ISO 11997-2:2013-12Beschichtungsstoffe B

3、estimmung der Bestndigkeit bei zyklischen Korrosionsbedingungen Teil 2: Nass (Salzsprhnebel)/trocken/Feuchte/UV-Strahlung (ISO 11997-2:2013);Englische Fassung EN ISO 11997-2:2013,Englische bersetzung von DIN EN ISO 11997-2:2013-12Peintures et vernis Dtermination de la rsistance aux conditions de cor

4、rosion cyclique Partie 2: Brouillard salin/scheresse/humidit/lumire UV (ISO 11997-2:2013);Version anglaise EN ISO 11997-2:2013,Traduction anglaise de DIN EN ISO 11997-2:2013-12SupersedesDIN EN ISO 11997-2:2006-04www.beuth.deIn case of doubt, the German-language original shall be considered authorita

5、tive.Document comprises 16 pages12.13 DIN EN ISO 11997-2:2013-12 2 A comma is used as the decimal marker. National foreword This document (EN ISO 11997-2:2013) has been prepared by Technical Committee ISO/TC 35 “Paints and varnishes” in collaboration with Technical Committee CEN/TC 139 “Paints and v

6、arnishes” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Beschichtungsstoffe und Beschichtungen (Coatings and Coating Materials Standards Committee), Working Committee NA 002-00-07 AA Allgemeine Prfverfahren fr Beschichtungsstoffe und Bes

7、chichtungen. DIN EN ISO 11997 consists of the following parts, under the general title Paints and varnishes Determination of resistance to cyclic corrosion conditions: Part 1: Wet (salt fog)/dry/humidity Part 2: Wet (salt fog)/dry/humidity/UV light This part of DIN EN ISO 11997 is equivalent to ASTM

8、 D 5894-05, Standard Practice for Cyclic Salt Fog/UV exposure of Painted Metal, (Alternating Exposures in a Fog/Dry Cabinet and a UV/Condensation Cabinet). The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 1513 DIN EN ISO 1513 ISO 1514 DI

9、N EN ISO 1514 ISO 2808 DIN EN ISO 2808 ISO 3270 DIN EN 23270 ISO 3696 DIN ISO 3696 ISO 4628-1 DIN EN ISO 4628-1 ISO 4628-2 DIN EN ISO 4628-2 ISO 4628-3 DIN EN ISO 4628-3 ISO 4628-4 DIN EN ISO 4628-4 ISO 4628-5 DIN EN ISO 4628-5 ISO 4628-6 DIN EN ISO 4628-6 ISO 4628-8 DIN EN ISO 4628-8 ISO 4628-10 DI

10、N EN ISO 4628-10 ISO 4892-2 DIN EN ISO 4892-2 ISO 4892-3 DIN EN ISO 4892-3 ISO 9227 DIN EN ISO 9227 ISO 11341 DIN EN ISO 11341 ISO 11507 DIN EN ISO 11507 ISO 11997-1:2005 DIN EN ISO 11997-1:2006-04 ISO 15528 DIN EN ISO 15528 ISO 16151 DIN EN ISO 16151 ISO 16474-2 DIN EN ISO 16474-2 ISO 16474-3 DIN E

11、N ISO 16474-3 ISO 17872 DIN EN ISO 17872 DIN EN ISO 11997-2:2013-12 3 For the International Standards ISO 2135, ISO 4892-4, ISO 14993 and ISO 16474-4 referred to in this standard, there are no national standards available. Amendments This standard differs from DIN EN ISO 11997-2:2006-04 as follows:

12、a) alternative test procedures have been added as an informative annex; b) the supplementary test conditions (formerly Annex A) have been incorporated in the test report. Previous editions DIN EN ISO 11997-2: 2006-04 National Annex NA (informative) Bibliography DIN EN 23270, Paints, varnishes and th

13、eir raw materials Temperatures and humidities for conditioning and testing DIN EN ISO 1513, Paints and varnishes Examination and preparation of test samples DIN EN ISO 1514, Paints and varnishes Standard panels for testing DIN EN ISO 2808, Paints and varnishes Determination of film thickness DIN EN

14、ISO 4628-1, Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 1: General introduction and designation system DIN EN ISO 4628-2, Paints and varnishes Evaluation of degradation of coatings Desi

15、gnation of quantity and size of defects, and of intensity of uniform changes in appearance Part 2: Assessment of degree of blistering DIN EN ISO 4628-3, Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appe

16、arance Part 3: Assessment of degree of rusting DIN EN ISO 4628-4, Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 4: Assessment of degree of cracking DIN EN ISO 4628-5, Paints and varnishes

17、 Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 5: Assessment of degree of flaking DIN EN ISO 11997-2:2013-12 4 DIN EN ISO 4628-6, Paints and varnishes Evaluation of degradation of coatings Designation of quan

18、tity and size of defects, and of intensity of uniform changes in appearance Part 6: Assessment of degree of chalking by tape method DIN EN ISO 4628-8, Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appear

19、ance Part 8: Assessment of degree of delamination and corrosion around a scribe or other artificial defect DIN EN ISO 4628-10, Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 10: Assessment

20、 of degree of filiform corrosion DIN EN ISO 4892-2, Plastics Methods of exposure to laboratory light sources Part 2: Xenon-arc lamps DIN EN ISO 4892-3, Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps DIN EN ISO 9227, Corrosion tests in artificial atmospheres Sal

21、t spray tests DIN EN ISO 11507, Paints and varnishes Exposure of coatings to artificial weathering Exposure to fluorescent UV lamps and water DIN EN ISO 11341, Paints and varnishes Artificial weathering and exposure to artificial radiation Exposure to filtered xenon-arc radiation DIN EN ISO 11507, P

22、aints and varnishes Exposure of coatings to artificial weathering Exposure to fluorescent UV lamps and water DIN EN ISO 11997-1:2005, Paints and varnishes Determination of resistance to cyclic corrosion conditions Part 1: Wet (salt fog)/dry/humidity DIN EN ISO 15528, Paints, varnishes and raw materi

23、als for paints and varnishes Sampling DIN EN ISO 16151, Corrosion of metals and alloys Accelerated cyclic tests with exposure to acidified salt spray, “dry” and “wet” conditions DIN EN ISO 16474-2, Paints and varnishes Methods of exposure to laboratory light sources Part 2: Xenon-arc lamps DIN EN IS

24、O 16474-3, Paints and varnishes Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps DIN EN ISO 17872, Paints and varnishes Guidelines for the introduction of scribe marks through coatings on metallic panels for corrosion testing DIN ISO 3696, Water for analytical laboratory

25、use Specification and test methods EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 11997-2 September 2013 ICS 87.040 Supersedes EN ISO 11997-2:2006English Version Paints and varnishes - Determination of resistance to cyclic corrosion conditions - Part 2: Wet (salt fog)/dry/humidity/UV light

26、 (ISO 11997-2:2013) Peintures et vernis - Dtermination de la rsistance aux conditions de corrosion cyclique - Partie 2: Brouillard salin/scheresse/humidit/lumire UV (ISO 11997-2:2013)Beschichtungsstoffe - Bestimmung der Bestndigkeit bei zyklischen Korrosionsbedingungen - Teil 2: Nass (Salzsprhnebel)

27、/trocken/Feuchte/UV-Strahlung (ISO 11997-2:2013) This European Standard was approved by CEN on 17 August 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alte

28、ration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language mad

29、e by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Eston

30、ia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STAND

31、ARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 11997-2:2013: EContents Page Forewor

32、d . 3 Introduction . 4 1 Scope . 5 2 Normative references. 5 3 Principle 6 4 Salt fog test solution 6 5 Apparatus 6 6 Sampling . 7 7 Test panels 7 7.1 Material and dimensions . 7 7.2 Preparation and coating of panels . 7 7.3 Drying and conditioning 7 7.4 Thickness of coating 7 7.5 Scribing of panels

33、 7 8 Procedure 7 9 Examination of test panels 8 10 Precision . 8 11 Test report . 8 Annex A (informative) Alternative test procedures 10 Bibliography 12 2DIN EN ISO 11997-2:2013-12EN ISO 11997-2:2013 (E) This document (EN ISO 11997-2:2013) has been prepared by Technical Committee ISO/TC 35 Paints an

34、d varnishes in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2014, and con

35、flicting national standards shall be withdrawn at the latest by March 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This docum

36、ent supersedes EN ISO 11997-2:2006. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugosla

37、v Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 11997-2:2013 has

38、 been approved by CEN as EN ISO 11997-2:2013 without any modification. Foreword“”3DIN EN ISO 11997-2:2013-12EN ISO 11997-2:2013 (E)IntroductionCoatings of paints, varnishes and similar materials are exposed to cyclic wet and dry corrosion and UV exposure conditions using specified salt solutions in

39、cabinets in order to simulate, in the laboratory, processes occurring in aggressive outdoor conditions. Generally, valid correlations between such outdoor weathering and laboratory testing cannot be expected because of the large number of factors influencing the breakdown process. Certain relationsh

40、ips can only be expected if the effect on the coating of the important parameters (e.g. nature of the pollutant, spectral distribution of the incident irradiance in the relevant photochemical region, temperature of the specimen, type and cycle of wetting and relative humidity) is known. In contrast

41、to outdoor weathering, laboratory testing in a cabinet is performed with a reduced number of variables, which can be controlled and therefore the effects are more reproducible.The method described can give a means of checking that the quality of a paint or paint system is being maintained. The metho

42、d is intended to provide a more realistic simulation of these factors than is found in traditional tests with continuous exposure to a static set of corrosive conditions. The method has been found to be useful in comparing the cyclic salt spray resistance of different coatings. It is most useful in

43、providing relevant ratings for a series of coated panels exhibiting significant differences in cyclic salt spray/UV exposure resistance tested at the same time and to the same test cycle.The cycle specified in this part of ISO 11997 has been found useful for air-drying industrial maintenance coating

44、s on steel; other cycles may be used as required.4DIN EN ISO 11997-2:2013-12EN ISO 11997-2:2013 (E) 1 ScopeThis part of ISO 11997 specifies a test method of determining resistance of coatings to a defined cycle of wet (salt fog)/dry/humidity/UV light conditions using a specified solution.2 Normative

45、 referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) appli

46、es.ISO 1513, Paints and varnishes Examination and preparation of test samplesISO 1514, Paints and varnishes Standard panels for testingISO 2808, Paints and varnishes Determination of film thicknessISO 3270, Paints and varnishes and their raw materials Temperatures and humidities for conditioning and

47、 testingISO 3696, Water for analytical laboratory use Specification and test methodsISO 4628-1, Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 1: General introduction and designation syste

48、mISO 4628-2, Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 2: Assessment of degree of blisteringISO 4628-3, Paints and varnishes Evaluation of degradation of coatings Designation of quant

49、ity and size of defects, and of intensity of uniform changes in appearance Part 3: Assessment of degree of rustingISO 4628-4, Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 4: Assessment of degree of crackingISO 4628-5, Paints and varn