DIN EN ISO 12181-1-2011 Geometrical product specifications (GPS) - Roundness - Part 1 Vocabulary and parameters of roundness (ISO 12181-1 2011) German version EN ISO 12181-1 2011《产.pdf

1、July 2011 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 0

2、1.040.17; 17.040.30!$sg“1805668www.din.deDDIN EN ISO 12181-1Geometrical product specifications (GPS) Roundness Part 1: Vocabulary and parameters of roundness (ISO 12181-1:2011)English translation of DIN EN ISO 12181-1:2011-07Geometrische Produktspezifikation (GPS) Rundheit Teil 1: Begriffe und Kenng

3、ren der Rundheit (ISO 12181-1:2011)Englische bersetzung von DIN EN ISO 12181-1:2011-07Spcification gomtrique des produits (GPS) Circularit Partie 1: Vocabulaire et paramtres de circularit (ISO 12181-1:2011)Traduction anglaise de DIN EN ISO 12181-1:2011-07SupersedesDIN ISO/TS 12181-1:2008-05www.beuth

4、.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.2107.11 DIN EN ISO 12181-1:2011-07 2 National foreword This standard has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification” i

5、n collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Technische Grundlagen (Fundamental Technical Standards Committee), Wo

6、rking Committee NA 152-03-02-13 UA Formprfung (GMA 3.21). The International Standards ISO 12180-1 and ISO 12180-2 ISO 12181-1 and ISO 12181-2 ISO 12780-1 and ISO 12780-2 ISO 12781-1 and ISO 12781-2 defining the vocabulary (Parts 1) and the principles of measurement (Parts 2) of deviations from round

7、ness, cylindricity, straightness and flatness have been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification”. The responsible German body involved in its preparation was the Joint Working Committee DIN NA 152-03-02-13 UA/VDI/VDE-GMA 3.21 Fo

8、rmprfung which recommends: Users of this standard should note that the provisions in Part 2 of the respective standard regarding probe tip radius, probing force, defaults for filter undulation, method of association are representative of idealized measurement conditions. As a basis for the practical

9、 implementation, the Joint Working Committee established the VDI/VDE 2631 guideline series on form measurement. The abbreviation UPR is the internationally accepted unit for undulations per revolution/Wellenanzahl pro Umdrehung. In German, the abbreviation W/U is also most common. The DIN Standards

10、corresponding to the International Standards referred to in this document are as follows: ISO 14660-1 DIN EN ISO 14660-1 ISO 14660-2 DIN EN ISO 14660-2 ISO 17450-1 DIN EN ISO 17450-11)1) In preparation. DIN EN ISO 12181-1:2011-07 3 Amendments This standard differs from DIN ISO/TS 12181-1:2008-05 as

11、follows: a) the Technical Specification has been adopted as an International Standard; b) the standard has been technically revised. Previous editions DIN ISO 4291: 1987-09 DIN ISO 6318: 1987-09 DIN ISO/TS 12181-1: 2005-07, 2008-05 National Annex NA (informative) Bibliography DIN EN ISO 14660-1, Geo

12、metrical Product Specifications (GPS) Geometrical features Part 1: General terms and definitions DIN EN ISO 14660-2, Geometrical Product Specifications (GPS) Geometrical features Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature DIN

13、EN ISO 17450-1, Geometrical product specifications (GPS) General concepts Part 1: Model for geometrical specification and verification DIN EN ISO 12181-1:2011-07 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 12181-1 April 2011 ICS 01.040.17; 17.040.20 Su

14、persedes CEN ISO/TS 12181-1:2007English Version Geometrical product specifications (GPS) - Roundness - Part 1: Vocabulary and parameters of roundness (ISO 12181-1:2011) Spcification gomtrique des produits (GPS) - Circularit -Partie 1: Vocabulaire et paramtres de circularit (ISO 12181-1:2011) Geometr

15、ische Produktspezifikation (GPS) - Rundheit - Teil 1: Begriffe und Kenngren der Rundheit (ISO 12181-1:2011) This European Standard was approved by CEN on 17 March 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European S

16、tandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (Eng

17、lish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium,

18、 Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTE

19、E FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 12181-1:2011: EContents Page Foreword

20、3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 3.1 General terms.5 3.2 Terms relating to profiles6 3.3 Terms relating to the reference circle7 3.4 Terms relating to the circumference8 3.5 Terms relating to the filter function .8 3.6 Terms relating to parameters .9 An

21、nex A (informative) Mathematical definition of roundness tolerances of nominal integral features .11 Annex B (informative) Synoptic tables of terms, abbreviated terms and parameters .13 Annex C (informative) Relationship to the GPS matrix model15 Bibliography 17 EN ISO 12181-1:2011 (E) DIN EN ISO 12

22、181-1:2011-07 2 Foreword This document (EN ISO 12181-1:2011) has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification” in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verificat

23、ion” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at the latest by October 2011. A

24、ttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN ISO/TS 12181-1:2007. ISO 12181 consists of the following p

25、arts, under the general title Geometrical product specifications (GPS) Roundness: Part 1: Vocabulary and parameters of roundness Part 2: Specification operators According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement t

26、his European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerla

27、nd and the United Kingdom. Endorsement notice The text of ISO 12181-1:2011 has been approved by CEN as a EN ISO 12181-1:2011 without any modification. EN ISO 12181-1:2011 (E) DIN EN ISO 12181-1:2011-07 3 Introduction This part of ISO 12181 is a geometrical product specification (GPS) standard and is

28、 to be regarded as a general GPS standard (see ISO/TR 14638). It influences chain link 2 of the chain of standards on form of a surface (independent of a datum). The ISO/GPS Masterplan given in ISO/TR 14638 gives an overview of the ISO/GPS system of which this document is a part. The fundamental rul

29、es of ISO/GPS given in ISO 8015 apply to this document and the default decision rules given in ISO 14253-1 apply to specifications made in accordance with this document, unless otherwise indicated. For more detailed information on the relationship of this part of ISO 12181 to other standards and the

30、 GPS matrix model, see Annex C. This part of ISO 12181 defines terms and concepts necessary for defining the specification operators according to ISO 17450-2 for roundness of integral features. Extracting data always involves applying a certain filtering process. An additional filtering of the extra

31、cted data might or might not be applied. This additional filter can be a mean line filter (Gaussian, spline, wavelet, etc.) or a non-linear filter (e.g. morphological filter). The type of filtering influences the actual specification operator and, consequently, the actual definition of roundness. Th

32、erefore, the type of filtering needs to be stated unambiguously. This part of ISO 12181 is not intended to disallow any means of measuring roundness. EN ISO 12181-1:2011 (E) DIN EN ISO 12181-1:2011-07 4 1 Scope This part of ISO 12181 defines the terms and concepts related to the roundness of individ

33、ual integral features and covers complete roundness profiles only. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docu

34、ment (including any amendments) applies. ISO 14660-1:1999, Geometrical Product Specifications (GPS) Geometrical features Part 1: General terms and definitions ISO 14660-2:1999, Geometrical Product Specifications (GPS) Geometrical features Part 2: Extracted median line of a cylinder and a cone, extra

35、cted median surface, local size of an extracted feature ISO 17450-1:1), Geometrical product specifications (GPS) General concepts Part 1: Model for geometrical specification and verification 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 14660-1, IS

36、O 14660-2 and ISO 17450-1 and the following apply. 3.1 General terms 3.1.1 roundness property of a circle 3.1.2 roundness axis axis of a feature associated to an integral feature NOTE The integral feature can be a cylindrical surface or a surface of revolution. EN ISO 12181-1:2011 (E) DIN EN ISO 121

37、81-1:2011-07 5 1) To be published. (Revision of ISO/TS 17450-1:2005) 3.1.3 roundness plane plane perpendicular to the roundness axis within the full extent of the feature 3.2 Terms relating to profiles 3.2.1 extracted circumferential line roundness digital representation of the intersection of the r

38、eal surface and the roundness plane NOTE The extraction conventions for roundness are given in ISO 12181-2. This extracted circumferential line is an extracted integral feature as defined in ISO 14660-1. 3.2.2 roundness profile extracted circumferential line intentionally modified by a filter NOTE T

39、his is the profile to which the concepts and parameters of this part of ISO 12181 can be applied. 3.2.3 local roundness deviation minimum distance from a point on a roundness profile to the reference circle See Figures 1 and 2. NOTE 1 For reference circle, see 3.3.1. NOTE 2 The deviation is negative

40、 if from the reference circle the point lies in the direction of the material. Key 1 reference circle aPositive local deviation. bNegative local deviation. Figure 1 Local form deviation of an internal roundness feature EN ISO 12181-1:2011 (E) DIN EN ISO 12181-1:2011-07 6 Key 1 reference circle aNega

41、tive local deviation. bPositive local deviation. Figure 2 Local form deviation of an external roundness feature 3.3 Terms relating to the reference circle 3.3.1 reference circle associated circle fitting the roundness profile in accordance with specified conventions, to which the deviations from rou

42、ndness and the roundness parameters are referred 3.3.1.1 minimum zone reference circles two concentric circles enclosing the roundness profile and having the least radial separation NOTE The abbreviated term MZ is used to refer to minimum zone reference elements. 3.3.1.1.1 outer minimum zone referen

43、ce circle outer circle of the minimum zone reference circles 3.3.1.1.2 inner minimum zone reference circle inner circle of the minimum zone reference circles 3.3.1.1.3 mean minimum zone reference circle arithmetic mean circle of the minimum zone reference circles 3.3.1.2 least squares reference circ

44、le circle such that the sum of the squares of the local roundness deviations is a minimum NOTE The abbreviated term LS is used to refer to least squares reference elements and the letter G (for Gaussian) is used as a prefix for parameters based on least squares reference elements. 3.3.1.3 minimum ci

45、rcumscribed reference circle smallest possible circle that can be fitted around the roundness profile NOTE The abbreviated term MC is used to refer to minimum circumscribed reference elements. EN ISO 12181-1:2011 (E) DIN EN ISO 12181-1:2011-07 7 3.3.1.4 maximum inscribed reference circle largest pos

46、sible circle that can be fitted within the roundness profile NOTE 1 Cases exist where the maximum inscribed reference circle is not unique. NOTE 2 The abbreviated term MI is used to refer to maximum inscribed reference elements. 3.3.2 associated derived centre centre of the reference circle(s) 3.4 T

47、erms relating to the circumference 3.4.1 undulations per revolution UPR number of sinusoidal undulations contained in the roundness profile 3.4.2 circumferential wavelength circumference of the reference circle divided by the UPR 3.5 Terms relating to the filter function 3.5.1 General NOTE 1 If not

48、otherwise specified, the details of the filter characteristics are as given in ISO 12181-2. NOTE 2 Only the phase correct mean line filter is defined (see ISO 11562). Consequently, the terms in this subclause relate only to this type of filter. Other filter methods are currently being investigated b

49、y ISO. It is intended to incorporate these new filters in a future edition of this part of ISO 12181. 3.5.2 wave filter filter operating on a closed profile, transmitting a range of sinusoidal undulations for which the ratio of output to input amplitude is defined, while attenuating (i.e. reducing) the ratio for undulations lying outside the range at either or both ends 3.5.3 undulation cut-off cut-off wavelength of the filter applied to the extracted circumferential line NOTE These are usually defined in