DIN EN ISO 14172-2016 Welding consumables - Covered electrodes for manual metal arc welding of nickel and nickel alloys - Classification (ISO 14172 2015) German version EN ISO 1417.pdf

1、February 2016 English price group 13No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 25.160.20!%LF“2413557www.din.de

2、DIN EN ISO 14172Welding consumables Covered electrodes for manual metal arc welding of nickel and nickel alloys Classification (ISO 14172:2015);English version EN ISO 14172:2015,English translation of DIN EN ISO 14172:2016-02Schweizustze Umhllte Stabelektroden zum Lichtbogenhandschweien von Nickel u

3、nd Nickellegierungen Einteilung (ISO 14172:2015);Englische Fassung EN ISO 14172:2015,Englische bersetzung von DIN EN ISO 14172:2016-02Produits consommables pour le soudage lectrodes enrobes pour le soudage manuel larc du nickel et des alliages de nickel Classification (ISO 14172:2015);Version anglai

4、se EN ISO 14172:2015,Traduction anglaise de DIN EN ISO 14172:2016-02SupersedesDIN EN ISO 14172:2009-03www.beuth.deDocument comprises 25 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.02.16 DIN EN ISO 14172:2016-02 2 A comma is

5、 used as the decimal marker. National foreword This document (EN ISO 14172:2015) has been prepared by Technical Committee ISO/TC 44 “Welding and allied processes” (Secretariat AFNOR, France) in collaboration with Technical Committee CEN/TC 121 “Welding and allied processes” (Secretariat: DIN, German

6、y). The responsible German body involved in its preparation was DIN-Normenausschuss Schweien und verwandte Verfahren (DIN Standards Committee Welding and Allied Processes), Working Committee NA 092-00-03 AA Schweizustze (DVS AG W 5). The DIN Standards corresponding to the International Standards ref

7、erred to in this document are as follows: ISO 554 DIN EN ISO 544 ISO 6847 DIN EN ISO 6847 ISO 14344 DIN EN ISO 14344 ISO 15972-1:2000 + Amd 1:2011 DIN EN ISO 15792-1:2012-01 ISO 80000-1:2009 + Cor 1:2011 DIN EN ISO 80000-1:2013-08 Amendments This standard differs from DIN EN ISO 14172:2009-03 as fol

8、lows: a) Table 1 has been technically and editorially revised; b) normative references have been updated. Previous editions DIN 1736-1: 1966-08, 1975-01, 1979-06, 1985-08 DIN 1736-2: 1980-04, 1985-08 DIN EN ISO 14172: 2004-05, 2009-03 DIN EN ISO 14172 Corrigendum 1: 2006-10 DIN EN ISO 14172 Corrigen

9、dum 2: 2007-06 National Annex NA (informative) Bibliography DIN EN ISO 544, Welding consumables Technical delivery conditions for filler materials and fluxes Type of product, dimensions, tolerances and markings DIN EN ISO 6847, Welding consumables Deposition of a weld metal pad for chemical analysis

10、 DIN EN ISO 14344, Welding consumables Procurement of filler materials and fluxes DIN EN ISO 15792-1:2012-01, Welding consumables Test methods Part 1: Test methods for all-weld metal test specimens in steel, nickel and nickel alloys (ISO 15792-1:2000 + Amd 1:2011) DIN EN ISO 80000-1:2013-08, Quantit

11、ies and units Part 1: General (ISO 80000-1:2009 + Cor 1:2011) EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 14172 September 2015 ICS 25.160.20 Supersedes EN ISO 14172:2008English Version Welding consumables - Covered electrodes for manual metal arc welding of nickel and nickel alloys - Cl

12、assification (ISO 14172:2015) Produits consommables pour le soudage - lectrodes enrobes pour le soudage manuel larc du nickel et des alliages de nickel - Classification (ISO 14172:2015)Schweizustze - Umhllte Stabelektroden zum Lichtbogenhandschweien von Nickel und Nickellegierungen - Einteilung (ISO

13、 14172:2015) This European Standard was approved by CEN on 10 July 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliogra

14、phical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibil

15、ity of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic

16、of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATI

17、ON EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 14172:2015 EForeword 41 Scope . 52 Normative references 53 Classification 5

18、4 Symbols and requirements 54.1 Symbol for the product/process 54.2 Symbol for the chemical composition of the all-weld metal . 64.3 Rounding procedure. 65 Chemical analysis . 66 Mechanical properties of the all-weld metal. 67 Retests 128 Technical delivery conditions 129 Designation .13Annex A (inf

19、ormative) System for designation of welding filler metals .14Annex B (informative) Description of consumables classes .15Annex C (informative) Equivalent national specifications .21Bibliography .23Contents PageDIN EN ISO 14172:2016-02 EN ISO 14172:2015 (E)2European Foreword 3European foreword This d

20、ocument (EN ISO 14172:2015) has been prepared by Technical Committee ISO/TC 44 “Welding and allied processes“ in collaboration with Technical Committee CEN/TC 121 “Welding and allied processes” the secretariat of which is held by DIN. This European Standard shall be given the status of a national st

21、andard, either by publication of an identical text or by endorsement, at the latest by March 2016, and conflicting national standards shall be withdrawn at the latest by March 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.

22、CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 14172:2008. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard

23、: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,

24、 Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 14172:2015 has been approved by CEN as EN ISO 14172:2015 without any modification. DIN EN ISO 14172:2016-02 EN ISO 14172:2015 (E)3 ForewordISO (the International Organization for Standardization) is a worldwide f

25、ederation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that co

26、mmittee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document

27、and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, P

28、art 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of

29、 the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific

30、terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 44, Welding and allied p

31、rocesses, Subcommittee SC 3, Welding consumables.Requests for official interpretations of any aspect of this International Standard should be directed to the Secretariat of ISO/TC 44/SC 3 via your national standards body. A complete listing of these bodies can be found at www.iso.org.This third edit

32、ion cancels and replaces the second edition (ISO 14172:2008), which has been technically revised.DIN EN ISO 14172:2016-02 EN ISO 14172:2015 (E)4 1 ScopeThis International Standard prescribes requirements for the classification of nickel and nickel-alloy covered electrodes for manual metal arc weldin

33、g and overlaying. It includes those compositions in which the nickel content exceeds that of any other element.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edi

34、tion cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 544, Welding consumables Technical delivery conditions for filler materials and fluxes Type of product, dimensions, tolerances and markingsISO 6847, Welding consumables De

35、position of a weld metal pad for chemical analysisISO 14344, Welding consumables Procurement of filler materials and fluxesISO 15792-1:2000, Welding consumables Test methods Part 1: Test methods for all-weld metal test specimens in steel, nickel and nickel alloys. Amended by ISO 15792-1:2000/Amd 1:2

36、011.ISO 80000-1:2009, Quantities and units Part 1: General3 ClassificationA covered electrode shall be classified in accordance with the chemical composition of the all-weld metal as given in Table 1 and the mechanical properties listed in Table 2. The symbol for the classification is divided into t

37、wo parts:a) the first part gives a symbol indicating the product/process to be used;b) the second part gives a symbol indicating the chemical composition of the all-weld metal.4 Symbols and requirements4.1 Symbol for the product/processThe symbol for covered electrodes used for manual metal arc weld

38、ing shall be the letter “E”.DIN EN ISO 14172:2016-02 EN ISO 14172:2015 (E)5 4.2 Symbol for the chemical composition of the all-weld metalThe symbol for the chemical composition of the all-weld metal shall comprise “Ni” plus four digits, as shown in Table 1. The first digit is an indicator of the cla

39、ss of alloy deposited, where2 indicates no significant alloy addition,4 indicates significant copper addition (nickel-copper alloys),6 indicates significant chromium addition, with iron less than 25 % (nickel-chromium-iron and nickel-chromium-molybdenum alloys),8 indicates significant chromium addit

40、ion, with iron more than 25 % (nickel-iron-chromium alloys),10 indicates significant molybdenum addition without significant chromium addition (nick-el-molybdenum alloys).The remaining digits indicate the particular alloy deposited. The basis of the system of designation is described in Annex A.NOTE

41、 In addition, the chemical symbol can be used.4.3 Rounding procedureFor purposes of determining compliance with the requirements of this International Standard, the actual test values obtained shall be subject to ISO 80000-1:2009, B.3, Rule A. If the measured values are obtained by equipment calibra

42、ted in units other than those of this International Standard, the measured values shall be converted to the units of this International Standard before rounding. If an arithmetic average value is to be compared to the requirements of this International Standard, rounding shall be done only after cal

43、culating the arithmetic average. If the test method cited in Clause 2 contains instructions for rounding that conflict with the instructions of this International Standard, the rounding requirements of the test method standard shall apply. The rounded results shall fulfil the requirements of the app

44、ropriate table for the classification under test.5 Chemical analysisChemical analysis shall be performed on any suitable all-weld metal test specimen. In case of dispute, the test specimen specified in ISO 6847 shall be used. The test results shall meet the requirements of Table 1 for the classifica

45、tion under test. Any analytical technique can be used; but, in case of dispute, reference shall be made to established published methods.6 Mechanical properties of the all-weld metalMechanical properties are not part of the designation, but they are required for classification. The mechanical proper

46、ties of the all-weld metal, deposited using covered electrodes in accordance with Table 1, shall be determined using a test assembly type 1.3 in accordance with ISO 15792-1:2000 with 4,0 mm electrodes. The minimum tensile properties shall be in accordance with Table 2.DIN EN ISO 14172:2016-02 EN ISO

47、 14172:2015 (E)6 Table 1 Symbols and all-weld metal chemical composition requirementsAlloy symbolChemical composition % (by mass)aNumer-ical symbolChemical symbolC Mn Fe Si Cu NibCo Al Ti Cr NbcMo V W Notesd, eNickelNi 2061 NiTi3 0,10 0,7 0,7 1,2 0,2min. 92,0 1,01,0 to 4,0 Nickel-CopperNi 4060 NiCu3

48、0Mn3Ti 0,15 4,0 2,5 1,527,0 to 34,0min. 62,0 1,0 1,0 Ni 4061 NiCu27Mn3NbTi 0,15 4,0 2,5 1,324,0 to 31,0min. 62,0 1,0 1,5 3,0 Nickel-ChromiumNi 6082 NiCr20Mn3Nb 0,102,0 to 6,04,0 0,8 0,5min. 63,0 0,518,0 to 22,01,5 to 3,02,0 Ni 6172 NiCr50Nb 0,10 1,5 1,0 1,0 0,25min. 41,0 48,0 to 52,01,0 to 2,5 0,02P 0,02SNi 6231 NiCr22W14Mo0,05 to 0,100,3 to 1,03,00,3 to 0,70,5min. 45,05,0 0,5 0,120,