DIN EN ISO 14583-2011 Hexalobular socket pan head screws (ISO 14583 2011) German version EN ISO 14583 2011《内六角花形盘头螺钉(ISO 14583-2011) 德文版本EN ISO 14583-2011》.pdf

1、June 2011 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 21

2、.060.10!$s0G“1801336www.din.deDDIN EN ISO 14583Hexalobular socket pan head screws (ISO 14583:2011)English translation of DIN EN ISO 14583:2011-06Flachkopfschrauben mit Innensechsrund (ISO 14583:2011)Englische bersetzung von DIN EN ISO 14583:2011-06Vis mtaux tte cylindrique bombe large six lobes inte

3、rnes (ISO 14583:2011)Traduction anglaise de DIN EN ISO 14583:2011-06SupersedesDIN EN ISO 14583:2002-05 andDIN EN ISO 14583 Corrigendum1:2006-03www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 2 pages06.111DIN EN ISO 14583:2011-06 A comma

4、 is used as the decimal marker. National foreword This standard has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Fasteners” (both secretariats are held by DIN, Germany). The responsible German body involved in its preparation was the

5、 Normenausschuss Mechanische Verbindungselemente (Fasteners Standards Committee), Working Committee NA 067-00-05 AA Klein-schrauben und gewindeformende Schrauben. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 225 DIN EN ISO 225 ISO 26

6、1 DIN ISO 261 ISO 898-1 DIN EN ISO 898-1 ISO 965-2 DIN ISO 965-2 ISO 3269 DIN EN ISO 3269 ISO 3506-1 DIN EN ISO 3506-1 ISO 4042 DIN EN ISO 4042 ISO 4759-1 DIN EN ISO 4759-1 ISO 6157-1 DIN EN 26157-1 ISO 8839 DIN EN 28839 ISO 8992 DIN ISO 8992 ISO 10664 DIN EN ISO 10664 ISO 10683 DIN EN ISO 10683 Ame

7、ndments This standard differs from DIN EN ISO 14583:2002-05 and DIN EN ISO 14583 Corrigendum 1:2006-03 as follows: a) Corrigendum 1:2006-03 has been incorporated (Table 1, dimension rmin instead of rmax);b) normative references are now undated; c) in Table 1, a new footnote c has been added; d) in T

8、able 2, specifications for other finishes and coatings have been added; e) Annex ZA has been deleted. Previous editions DIN EN ISO 14583: 2002-05 DIN EN ISO 14583 Corrigendum 1: 2006-03 2 DIN EN ISO 14583:2011-06 3 National Annex NA (informative) Bibliography DIN EN 26157-1, Fasteners; surface disco

9、ntinuities Bolts, screws and studs subject to general require-ments DIN EN 28839, Mechanical properties of fasteners Nonferrous metal bolts, screws, studs and nuts DIN EN ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions DIN EN ISO 898-1, Mechanical properties o

10、f fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolt

11、s, screws and studs DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C DIN EN ISO 10664, Hexalobular internal driving feature for bolts and screws DIN EN ISO 10683, Fasteners Non-electrolytical

12、ly applied zinc flake coatings DIN ISO 261, ISO general purpose metric screw threads General plan DIN ISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium quality DIN ISO 8992, Fasteners General requirem

13、ents for bolts, screws, studs and nuts DIN EN ISO 14583:2011-06 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 14583 March 2011 ICS 21.060.10 Supersedes EN ISO 14583:2001English Version Hexalobular socket pan head screws (ISO 14583:2011) Vis mtaux tte cyl

14、indrique bombe large six lobes internes (ISO 14583:2011) Flachkopfschrauben mit Innnensechsrund (ISO 14583:2011) This European Standard was approved by CEN on 31 January 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Eur

15、opean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versio

16、ns (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, B

17、elgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Management

18、 Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 14583:2011: EEUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG 3 1 Scope 4 2 Nor

19、mative references4 3 Dimensions.5 4 Specifications and reference International Standards7 5 Designation.7 .8 ForewordContents PageBibliography.DIN EN ISO 14583:2011-06 EN ISO 14583:2011 (E) 2Foreword This document (EN ISO 14583:2011) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in c

20、ollaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2011, and conflicting national stand

21、ards shall be withdrawn at the latest by September 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN I

22、SO 14583:2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, I

23、celand, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 14583:2011 has been approved by CEN as a EN ISO 14583:2011 without any modification.

24、 EN ISO 14583:2011 (E) DIN EN ISO 14583:2011-06 31 Scope This International Standard specifies the characteristics of hexalobular socket pan head screws of product grade A and with thread sizes from M2 up to and including M10. If, in special cases, specifications other than those listed in this Inte

25、rnational Standard are required, they can be selected from existing International Standards, for example ISO 261, ISO 888, ISO 898-1, ISO 965-2, ISO 3506-1 and ISO 4759-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refe

26、rences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions ISO 261, ISO general-purpose metric screw threads General plan ISO

27、 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread ISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and

28、internal screw threads Medium quality ISO 3269, Fasteners Acceptance inspection ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs ISO 4042, Fasteners Electroplated coatings ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, st

29、uds and nuts Product grades A, B and C ISO 6157-1, Fasteners Surface discontinuities Part 1: Bolts, screws and studs for general requirements ISO 8839, Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metals ISO 8992, Fasteners General requirements for bolts, scre

30、ws, studs and nuts ISO 10664, Hexalobular internal driving feature for bolts and screws ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings DIN EN ISO 14583:2011-06 EN ISO 14583:2011 (E) 43 Dimensions See Figure 1 and Table 1. Symbols and descriptions of dimensions are specified in

31、 ISO 225. NOTE The shank diameter, ds, is approximately equal to the pitch diameter or equal to the major thread diameter. aAs-rolled end. Figure 1 EN ISO 14583:2011 (E) DIN EN ISO 14583:2011-06 5Table 1 Dimensions Dimensions in millimetres Thread, d M2 M2,5 M3 (M3,5)aM4 M5 M6 M8 M10 P b0,4 0,45 0,5

32、 0,6 0,7 0,8 1,0 1,25 1,5 a max. 0,8 0,9 1 1,2 1,4 1,6 2 2,5 3 b min. 25 25 25 38 38 38 38 38 38 damax. 2,6 3,1 3,6 4,1 4,7 5,7 6,8 9,2 11,2 nom. = max. 4,0 5,0 5,6 7,00 8,00 9,50 12,00 16,00 20,00 dkmin. 3,7 4,7 5,3 6,64 7,64 9,14 11,57 15,57 19,48 nom. = max. 1,60 2,10 2,40 2,60 3,10 3,70 4,6 6,0

33、7,50 k min. 1,46 1,96 2,26 2,46 2,92 3,52 4,3 5,7 7,14 r min. 0,1 0,1 0,1 0,1 0,2 0,2 0,25 0,4 0,4 rfg157 3,2 4 5 6 6,5 8 10 13 16 x max. 1,0 1,1 1,25 1,5 1,75 2,0 2,5 3,2 3,8 Socket no. 6 8 10 15 20 25 30 45 50 A ref. 1,75 2,4 2,8 3,35 3,95 4,5 5,6 7,95 8,95 max. 0,77 1,04 1,27 1,33 1,66 1,91 2,42

34、3,18 4,02 Hexalobular socketct min. 0,63 0,91 1,01 1,07 1,27 1,52 2,02 2,79 3,62 l dnom.amin. max. Approximate mass of carbon steel screws, in kilograms per 1 000 pieces (g85 = 7,85 kg/dm3) (for information only) 3 2,8 3,2 0,178 0,336 4 3,76 4,24 0,196 0,366 0,544 5 4,76 5,24 0,215 0,396 0,588 0,891

35、 1,30 6 5,76 6,24 0,233 0,426 0,632 0,951 1,38 2,32 8 7,71 8,29 0,270 0,486 0,720 1,07 1,53 2,57 4,37 10 9,71 10,29 0,307 0,546 0,808 1,19 1,69 2,81 4,72 9,96 12 11,65 12,35 0,344 0,606 0,896 1,31 1,84 3,06 5,07 10,6 19,8 (14) 13,65 14,35 0,381 0,666 0,984 1,43 2,00 3,31 5,42 11,2 20,5 16 15,65 16,3

36、5 0,418 0,726 1,07 1,55 2,15 3,56 5,78 11,9 21,8 20 19,58 20,42 0,492 0,846 1,25 1,79 2,46 4,05 6,48 13,2 23,8 25 24,58 25,42 0,996 1,47 2,09 2,85 4,67 7,36 14,8 26,3 30 29,58 30,42 1,69 2,39 3,23 5,29 8,24 16,4 28,8 35 34,5 35,5 2,68 3,62 5,91 9,12 18,0 31,3 40 39,5 40,5 4,01 6,52 10,0 19,6 33,9 45

37、 44,5 45,5 7,14 10,9 21,2 36,4 50 49,5 50,5 7,76 11,8 22,8 38,9 (55) 54,4 55,6 12,6 24,4 41,4 60 59,4 60,6 13,5 26,0 43,9 NOTE Preferred lengths are the ones between the solid, bold, stepped lines. a Sizes in parentheses should be avoided, if possible. b P is the pitch of the thread. c For the accep

38、tance of the hexalobular socket and for gauges, see ISO 10664. d Screws with nominal lengths above the discontinuous, stepped line are threaded up to the head (b = l a). DIN EN ISO 14583:2011-06 EN ISO 14583:2011 (E) 64 Specifications and reference International Standards See Table 2. Table 2 Specif

39、ications and reference International Standards Material Steel Stainless steel Non-ferrous metal General requirements International Standard ISO 8992 Tolerance class 6g Thread International Standard ISO 261, ISO 965-2 Property class 4.8 A2-70 A3-70 As agreed Mechanical property International Standard

40、 ISO 898-1 ISO 3506-1 ISO 8839 Product grade A Tolerance International Standard ISO 4759-1 Hexalobular socket International Standard ISO 10664 As processed As processed As processed Requirements for electroplating are specified in ISO 4042.Requirements for electroplating are specified in ISO 4042.Re

41、quirements for non-electrolytically applied zinc flake coatings are specified in ISO 10683. Finish Coating Additional requirements or other finishes or coatings shall be agreed between the supplier and the purchaser. Surface integrity Limits for surface discontinuities are specified in ISO 6157-1. A

42、cceptability Acceptance inspection is specified in ISO 3269. 5 Designation EXAMPLE A hexalobular socket pan head screw with thread M5, nominal length l = 20 mm and property class 4.8 is designated as follows: Hexalobular socket pan head screw ISO 14583 - M5 g150 20 - 4.8 EN ISO 14583:2011 (E) DIN EN ISO 14583:2011-06 7Bibliography 1 ISO 888, Bolts, screws and studs Nominal lengths, and thread lengths for general purpose bolts DIN EN ISO 14583:2011-06 EN ISO 14583:2011 (E) 8