DIN EN ISO 15147-2013 Light conveyor belts - Tolerances on widths and lengths of cut light conveyor belts (ISO 15147 2012) German version EN ISO 15147 2012《轻型输送带 切割轻型输送带的宽度和长度公差(IS.pdf

1、April 2013 Translation by DIN-Sprachendienst.English price group 6No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 5

2、3.040.20!$M“1999342www.din.deDDIN EN ISO 15147Light conveyor belts Tolerances on widths and lengths of cut light conveyor belts(ISO 15147:2012);English version EN ISO 15147:2012,English translation of DIN EN ISO 15147:2013-04Leichte Frdergurte Toleranzen fr Breite und Lnge von geschnittenen leichten

3、 Frdergurten(ISO 15147:2012);Englische Fassung EN ISO 15147:2012,Englische bersetzung von DIN EN ISO 15147:2013-04Courroies transporteuses lgres Tolrances sur largeurs et longueurs des courroies transporteuses lgres bordstranchs (ISO 15147:2012);Version anglaise EN ISO 15147:2012,Traduction anglaise

4、 de DIN EN ISO 15147:2013-04SupersedesDIN EN ISO 15147:1999-08www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.803.13DIN EN ISO 15147:2013-04 2 A comma is used as the decimal marker. National foreword This document has been prepared

5、 by Technical Committee ISO/TC 41 “Pulleys and belts (including veebelts)” (Secretariat: SAC, China), SC 3 “Conveyor belts” (Secretariat: SAC, China and JISC, Japan) and has been taken over as EN ISO 15147:2012 by Technical Committee CEN/TC 188 “Conveyor belts” (Secretariat: SNV, Switzerland). The r

6、esponsible German body involved in its preparation was the Normenausschuss Kautschuktechnik (Rubber Technology Standards Committee), Working Committee NA 045-02-05 AA Frdergurte. The DIN Standard corresponding to the International Standard referred to in this document is as follows: ISO 21183-1 DIN

7、EN ISO 21183-1 Amendments This standard differs from DIN EN ISO 15147:1999-08 as follows: a) the standard has been editorially revised. Previous editions DIN EN ISO 15147: 1999-08 National Annex NA (informative) Bibliography DIN EN ISO 21183-1, Light conveyor belts Part 1: Principal characteristics

8、and applications EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 15147 December 2012 ICS 53.040.20 Supersedes EN ISO 15147:1999English Version Light conveyor belts - Tolerances on widths and lengths of cut light conveyor belts (ISO 15147:2012) Courroies transporteuses lgres - Tolrances sur

9、largeurs et longueurs des courroies transporteuses lgres bords tranchs (ISO 15147:2012) Leichte Frdergurte - Toleranzen fr Breite und Lnge von geschnittenen leichten Frdergurten (ISO 15147:2012) This European Standard was approved by CEN on 30 November 2012. CEN members are bound to comply with the

10、CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management

11、Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as

12、 the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Net

13、herlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exp

14、loitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 15147:2012: EContents Page Foreword 3DIN EN ISO 15147:2013-04 EN ISO 15147:2012 (E) 2 Forew 1 Scope 4 2 Normative references 4 3 Widths .4 4 Lengths .4 4.1 Endless belts and open-ended belts with ends

15、 prepared for splicing . 4.2 Open-ended belts with ends not prepared for splicing (slab belting) 5 5 Methods of measurement and verification of dimensions 5 5.1 Determination of the cut width .5 5.2 Determination of the length of an endless light conveyor belt .5 5.3 Determination of the length of a

16、n open-ended light conveyor belt and of slab belting .6 4Foreword This document (EN ISO 15147:2012) has been prepared by Technical Committee ISO/TC 41 Pulleys and belts (including veebelts)” in collaboration with Technical Committee CEN/TC 188 “Conveyor belts” the secretariat of which is held by SNV

17、. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at the latest by June 2013. Attention is drawn to the possibility that some of th

18、e elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 15147:1999. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the

19、following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlan

20、ds, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 15147:2012 has been approved by CEN as a EN ISO 15147:2012 without any modification. “ DIN EN ISO 15147:2013-04 EN ISO 15147:2012 (E) 3 1 ScopeThis

21、 International Standard specifies methods for the measurement of widths and lengths of cut light conveyor belts as described in ISO 21183-1 and specifies the tolerances on the dimensions.NOTE The widths and lengths of light conveyor belts are not standardized.2 Normative referencesThe following docu

22、ments, in whole or in part, are normatively referenced in this document and are indispensable to its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 21183-1, Light conveyor

23、 belts Part 1: Principal characteristics and applications3 WidthsWhen measured in accordance with 5.1, the difference between the measured width and the specified cut width shall not vary by more than the tolerance specified in Table 1.It is recommended that actual cut widths of belt be specified in

24、 incremental steps of 50 mm for cut widths up to 1 m, and in incremental steps of 100 mm for cut widths over 1 m.Table 1 Tolerances on cut widths of light conveyor beltsWidthmmFor belts containing materials with low moisture absorption (e.g. polyester)For belts with higher moisture absorption (e.g.

25、cotton or polyamide)over up to and including- 200 1 mm 2 mm200 600 2 mm 3 mm600 1 000 4 mm 5 mm1 000 2 000 6 mm 6 mm2 000 4 000 7 mm 0,3 % of width4 000 - 8 mm 0,3 % of width4 Lengths4.1 Endless belts and open-ended belts with ends prepared for splicingWhen measured in accordance with 5.2, the diffe

26、rence between the measured endless length and the specified endless length shall not vary by more than the tolerance specified in Table 2.DIN EN ISO 15147:2013-04 EN ISO 15147:2012 (E) 4 Table 2 Tolerances on lengths of endless belts and of open-ended belts with ends prepared for splicingLengthmTole

27、ranceover up to and including- 2 10 mm2 7 20 mm7 - 0,3 %4.2 Open-ended belts with ends not prepared for splicing (slab belting)When measured in accordance with 5.3, the difference between the measured length and the manufacturers stated length shall not vary by more than 025+ ,%.5 Methods of measure

28、ment and verification of dimensions5.1 Determination of the cut width5.1.1 The measurements in 5.2 or 5.3 may be taken at the same time as the measurements in 5.1.5.1.2 Unroll the conveyor belt on a flat hard surface free from tension.5.1.3 Measure at three equidistant locations, throughout the leng

29、th of the belt and at right angles to the cut edges, the width of the conveyor belt to the nearest 0,5 mm, using a suitable linear measure (e.g. a steel tape).5.2 Determination of the length of an endless light conveyor belt5.2.1 Lay the conveyor belt flat, and free from tension.5.2.2 Mark the insid

30、e edge of the belt with an appropriate marker to indicate the point at which measurements begin (points A, B, C, D, etc., the last point being point X).Using a steel tape measure, make individual measurements along the flat part of the belt only (see Figure 1).Rotate the belt and make consecutive me

31、asurements along the flat part of the belt (BC;CD; etc.) (see Figure 1), continuing until the last measurement can be taken, e.g. XA .5.2.3 Calculate the endless length, le, of the belt as the sum of all the individual measurements minus the product of and the belt thickness,i.e. AB + BC + CD + XA a

32、 where a is the belt thickness.The calculation with the subtraction sum a is strictly correct only for conveyor belts with a symmetrical construction, i.e. with the neutral line in the belt middle. It is in most cases sufficiently exact also for conveyor belts with an asymmetrical construction. Howe

33、ver, short or thick conveyor belts with asymmetrical constructions may need a more precise calculation. The subtraction sum then becomes 2ai where ai is the distance between the neutral line and the inner belt surface (running surface). The value of aisshall be enquired of the belt manufacturer.(For

34、 symmetrical belt constructions, ai = a2and 2 ai becomes a.)DIN EN ISO 15147:2013-04 EN ISO 15147:2012 (E) 5 This value is the internal endless length of the belt.In cases where the method of measurement described above is not applicable, e.g. when the endless belt is very short, another suitable me

35、thod of measurement should be agreed between the belt user and supplier.A B Figure 1 Measurement of the length of an endless light conveyor belt5.3 Determination of the length of an open-ended light conveyor belt and of slab beltingDetermine the length of an open-ended light conveyor belt and of sla

36、b belting by employing any suitable mechanical, electromechanical or photoelectric means of linear measurement which does not exert any tension in to the conveyor belt and which is accurate to 01+ %of the recorded or designated length.With the end of the roll coinciding with the zero mark on the mea

37、suring surface, unroll the conveyor belt along the surface in such a manner that no tension is introduced. On reaching the limit of the surface, mark the roll by some suitable method on both edges to coincide with a known division of length. Re-roll the portion that has been measured. Lay out, free

38、from tension, a further portion of the unmeasured length and measure from the marked edges as before. Repeat this process until the end of the roll appears. Measure the final length and record the overall length as the sum of the individual measurements taken.DIN EN ISO 15147:2013-04 EN ISO 15147:2012 (E) 6