DIN EN ISO 15480-2000 Hexagon washers head drilling screws with tapping screw thread (ISO 15480 1999) German version EN ISO 15480 1999《六角凸缘头自钻自攻螺钉》.pdf

1、Hexagon washer head drilling screws with tapping screw thread (IS0 15480 : 1999) English version of DIN EN IS0 15480 ICs 21.060.10 Sechskant-Bohrschrauben mit Bund mit Blechschraubengewinde (IS0 15480 : 1999) DIN EN IS0 15480 - This standard, together with DIN EN IS0 10666, DIN EN IS0 15481, DIN EN

2、IS0 15482, and DIN EN IS0 15483, February 2000 editions, supersedes DIN 7504, September 1995 edition. European Standard EN IS0 15480 : 1999 has the status of a DIN Standard. A comma is used as the decimal marker. National foreword This standard has been published in accordance with a decision taken

3、by CEN/TC 185 to adopt, without alteration, International Standard IS0 15480 as a European Standard. The responsible German body involved in its preparation was the Normenausschuss Mechanische Ver- bindungse/emenfe (Fasteners Standards Committee). The DIN Standards corresponding to the International

4、 Standards referred to in clause 2 of the EN are as follows: IS0 Standard DIN Standard IS0 1478 IS0 3269 IS0 4042 IS0 10666 DIN EN IS0 1478 DIN EN IS0 3269*) DIN EN IS0 4042 DIN EN IS0 10666 IS0 4759-1 DIN EN IS0 4759-1 *) Amendments DIN 7504, September 1995 edition, has been superseded by the speci

5、fications of EN IS0 15480, which is identical to IS0 15480. Previo us edit ions DIN 7504: 1982-1 1, 1992-02, 1995-09. National Annex NA Standards referred to (and not included in Normative references and Annex ZA) DIN EN IS0 1478 DIN EN IS0 3269 DIN EN IS0 4042 DIN EN IS0 4759-1 DIN EN IS0 10666 Tap

6、ping screw threads (IS0 1478 : 1999) Fasteners - Acceptance inspection (ISO/DIS 3269 : 1998)*) Fasteners - Electroplated coatings (IS0 4042 : 1999) Tolerances for fasteners - Part 1 : Bolts, screws, studs and nuts - Product grades A, B and C (ISO/DIS 4759-1 : 1997)*) Drilling screws with tapping scr

7、ew thread - Mechanical and functional properties (IS0 10666 : 1999) *) At present at draft stage. EN comprises 6 pages. Q No pari of this standard may be reproduced without the prior permission of Ref. No. DIN EN IS0 15480 : 2000-02 DIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH,

8、 10772 Berlin, Germany, has the exclusive right of sale for German Standards (DIN-Normen). English price group 07 Sales No. 1107 07.00 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 15480 September 1999 ICs 21.060.1 O English version Hexagon washer head drilling screws with tapping screw t

9、hread (IS0 15480 : 1999) Vis autoperceuses tte hexagonale embase plate, avec filetage de vis tle (IS0 15480 : 1999) Sechskant-Bohrschrauben mit Bund mit Blechschraubengewinde (IS0 15480 : 1999) This European Standard was approved by CEN on 1999-07-1 6. CEN members are bound to comply with the CENKEN

10、ELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stand- ards may be obtained on application to the Central Secretariat or to an

11、y CEN member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CE

12、N members are the national standards bodies of Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. CEN European Committee for Standardization Comit

13、 Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels O 1999. CEN - All rights of exploitation in any form and by any means reserved worldwide for CEN national members. Ref. No. EN IS0 15480 : 1999 E Page 2 EN IS0 15480 : 1999 Foreword Inte

14、rnational Standard IS0 15480 : 1999 which was prepared by ISO/TC 2 ?Fasteners? of the International Organization for Standardization, has been adopted by Technical Committee CEN/TC 185 ?Threaded and non-threaded mechanical fasteners and acces- sories?, the Secretariat of which is held by DIN, as a E

15、uropean Standard. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, and conflicting national standards withdrawn, by March 2000 at the latest. In accordance with the CENKENELEC Internal Regulations, the national sta

16、ndards organizations of the follow- ing countries are bound to implement this European Standard: Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom

17、. Hexagon washer head drilling screws with tapping screw thread, Endorsement notice The text of the International Standard IS0 15480 : 1999 was approved by CEN as a European Standard without any modification. NOTE: Normative references to international publications are listed in Annex ZA (normative)

18、. 1 Scope This International Standard specifies the characteristics of hexagon washer head drilling screws with tapping screw threads from ST2,9 up to and including ST6,3. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute pr

19、ovisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of

20、the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of IS0 and IEC maintain registers of currently valid International Standards. IS0 1478:1999, Tapping screw thread. IS0 3269:-? ), Fasteners - Acceptance inspecti

21、on. IS0 4042:1999, fasteners - Electroplated coatings. IS0 4759-1 :-z), Tolerances for fasteners - Part 1: Bolts, screws, studs and nuts - Product grades A, B and C. IS0 10666:1999, Drilling screws with tapping screw thread - Mechanical and functional properties. ?)To be published. (Revision of IS0

22、3269:1988) *)To be published. (Revision of IS0 4759-1:1978) Page 3 EN IS0 15480 : 1999 3 Dimensions See Figure 1 and Table 1 a The function of the drilling point (diameter d,) is specified in IS0 10666 Figure 1 Page 4 EN IS0 15480 : 1999 S nom. = max. min. e min. Table 1 - Dimensions Dimensions in m

23、illimetres 4,OOc 5,50 7,OO 8,OO 8,OO 10,oo 3,82 5,32 6,7a 7,7a 7,78 9,78 4,28 5,96 739 8,71 8,71 10,95 I Thread I ST2,9 I CT3,5 I ST4,2 I ST4,8 I ST5,5 I ST6,3 ri max. 2 max. Drilling range from (sheet or plate thickness)e to I Pa I 1.1 I 1.3 I 1.4 I 1.6 1 1.8 I 1.8 0,4 0,s 0,6 Q7 08 0,9 02 0,25 0.3

24、 0.3 0,4 OS 0,7 0-7 1,75 1,75 1,75 2 1,g 2,25 3 4,4 5,25 6 9,5 13 16 19 22 k nom. = max. I 2,8 I 3,4 I 4,l I 4,3 I 5,4 I 5,9 8,75 10,25 3,25 2,85 12,l 13,9 6,6 62 4,3 3,7 15,l 16,9 9,6 92 7,3 53 5 18 20 12,5 12,l 10,3 8,7 8 7 21 23 15,l 13,3 11,7 11 10 min. I 2,5 I 3,O I 3,6 I 3,8 I 4,8 I 5,3 lgf mi

25、n. Page 5 EN IS0 15480 : 1999 Material International Standard Thread International Standard 4 Specifications and reference International Standards See Table 2. Steel IS0 10666 IS0 1478 Table 2 - Specifications and reference International Standards Tolerances Product grade International Standard Fini

26、sh Acceptability A IS0 4759-1 Plain Requirements for electroplating are covered in IS0 4042. Acceptance procedure is covered in IS0 3269. Mechanical and functional International Standard I properties I I IS0 10666 5 Designation EXAMPLE A hexagon washer head drilling screw with thread ST3.5 and nomin

27、al length i = 16 rnrn is designated as follows: Drilling screw IS0 15480 - ST3,5 x 16 Bibliography l IS0 1479:1983, Hexagon head tapping screws. 2 IS0 7053:1992, Hexagon washer head tapping screws. Page 6 EN IS0 15480 : 1999 Annex ZA (normative) Normative references to international publications wit

28、h their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendme

29、nts to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. Publication Year Title - EN Year IS0 1478 1999 Tapping screws thread EN IS0 1478 1999 IS0 1479 1983 Hexagon head tapping screws EN IS0 1479 1994 IS0 4042 1999 Fasteners - Electroplated coatings EN IS0 4042 1999