DIN EN ISO 1622-1-2012 Plastics - Polystyrene (PS) moulding and extrusion materials - Part 1 Designation system and basis for specifications (ISO 1622-1 2012) German version EN ISO.pdf

1、May 2012 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 83.

2、080.20!$.“1889411www.din.deDDIN EN ISO 1622-1Plastics Polystyrene (PS) moulding and extrusion materials Part 1: Designation system and basis for specifications(ISO 1622-1:2012)English translation of DIN EN ISO 1622-1:2012-05Kunststoffe Polystyrol (PS)-Formmassen Teil 1: Bezeichnungssystem und Basis

3、fr Spezifikationen (ISO 1622-1:2012)Englische bersetzung von DIN EN ISO 1622-1:2012-05Plastiques Polystyrne (PS) pour moulage et extrusion Partie 1: Systme de dsignation et base de spcification (ISO 1622-1:2012)Traduction anglaise de DIN EN ISO 1622-1:2012-05SupersedesDIN EN ISO 1622-1:1999-10www.be

4、uth.deDocument comprises 11 pagesIn case of doubt, the German-language original shall be considered authoritative.04.12 DIN EN ISO 1622-1:2012-05 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee ISO/TC 61 “Plastics”, Subcommitte SC 9 “

5、Thermoplastic materials” (Secretariat: KATS, Korea) in collaboration with Technical Committee CEN/TC 249 “Plastics”, (Secretariat: NBN, Belgium). The responsible German body involved in its preparation was the Normenausschuss Kunststoffe (Plastics Standards Committee), Technical Committee NA 054-02-

6、04 AA Polystyrol-Formmassen. DIN EN ISO 1622 “Plastics Polystyrene (PS) moulding and extrusion materials” consists of the following parts: Part 1: Designation system and basis for specifications Part 2: Preparation of test specimens and determination of properties The DIN Standard corresponding to t

7、he International Standard referred to in the EN ISO is as follows: ISO 1043-1 DIN EN ISO 1043-1 Amendments This standard differs from DIN EN ISO 1622-1:1999-10 as follows: a) the standard has been editorially revised; b) normative references in Clause 2 have been updated; they are now undated; c) NO

8、TE 1 in Subclause 3.4 “Data block 3” (formerly Subclause 3.3) has been deleted; d) for determining the Vicat softening temperature, ISO 1622-2 instead of ISO 306 now applies (3.4.2); e) the melt mass-flow rate (MFR) in accordance with ISO 1133 has been replaced by the melt volume-flow rate (MVR) in

9、accordance with ISO 1622-2; accordingly, NOTE 2 in Subclause 3.4.3 has been deleted and the values given in Table 3 have been changed; f) Annex ZA (normative) “Normative references to international publications with their relevant European publications” has been deleted. Previous editions DIN 7708-5

10、: 1955-09 DIN 7741: 1958-09, 1961-03 DIN 7741-1: 1968-09, 1977-08, 1986-12 DIN EN ISO 1622-1: 1999-10 DIN EN ISO 1622-1:2012-05 3 National Annex NA (informative) Bibliography DIN EN ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics DIN EN ISO

11、 1622-1:2012-05 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1622-1 February 2012 ICS 83.080.20 Supersedes EN ISO 1622-1:1999English Version Plastics - Polystyrene (PS) moulding and extrusion materials - Part 1: Designation system and basis for specific

12、ations (ISO 1622-1:2012) Plastiques - Polystyrne (PS) pour moulage et extrusion - Partie 1: Systme de dsignation et base de spcification (ISO 1622-1:2012) Kunststoffe - Polystyrol (PS)-Formmassen - Teil 1: Bezeichnungssystem und Basis fr Spezifikationen (ISO 1622-1:2012) This European Standard was a

13、pproved by CEN on 31 January 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nati

14、onal standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own langu

15、age and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latv

16、ia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-100

17、0 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1622-1:2012: EContents Page Foreword . 3 1 Scope . 4 2 Normative references . 4 3 Designation system 5 3.1 General . 5 3.2 Data block 1 . 5 3.3 Data block 2 . 5 3.

18、4 Data block 3 . 6 3.4.1 General . 6 3.4.2 Vicat softening temperature 6 3.4.3 Melt volume-flow rate . 7 3.5 Data block 5 . 7 4 Example of a designation 7 EN ISO 1622-1:2012 (E) DIN EN ISO 1622-1:2012-05 2Foreword This document (EN ISO 1622-1:2012) has been prepared by Technical Committee ISO/TC 61

19、“Plastics“ in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2012, and conflicting nat

20、ional standards shall be withdrawn at the latest by August 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document superse

21、des EN ISO 1622-1:1999. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, H

22、ungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 1622-1:2012 has been approved by CEN as a EN ISO 1622-1:2012 withou

23、t any modification. EN ISO 1622-1:2012 (E) DIN EN ISO 1622-1:2012-05 3 1 Scope1.1 This part of ISO 1622 establishes a system of designation for polystyrene thermoplastic material, which may be used as the basis for specifications.1.2 The types of polystyrene plastics are differentiated from each oth

24、er by a classification system based on appropriate levels of the designatory propertiesa) Vicat softening temperature andb) melt volume-flow rateand on information about the intended application and/or method of processing, important properties, additives and colorants.1.3 This part of ISO 1622 is a

25、pplicable to all amorphous polystyrene homopolymers.It applies to materials ready for normal use, unmodified or modified by colorants, additives, fillers, etc.This part of ISO 1622 does not apply to expanded polystyrene, styrene copolymers, homopolymers of substituted styrene or those modified with

26、other polymers such as elastomers.1.4 It is not intended to imply that materials having the same designation give necessarily the same performance. This part of ISO 1622 does not provide engineering data, performance data or data on processing conditions which might be required to specify a material

27、 for a particular application and/or method of processing.If such additional properties are required, they shall be determined in accordance with the test methods specified in Part 2 of this International Standard, if suitable.1.5 In order to specify a thermoplastic material for a particular applica

28、tion or to ensure reproducible processing, additional requirements may be given in data block 5 (see 3.1).2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the

29、 latest edition of the referenced document (including any amendments) applies.ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristicsISO 1622-2, Plastics Polystyrene (PS) moulding and extrusion materials Part 2: Preparation of test specimens and de

30、termination of propertiesEN ISO 1622-1:2012 (E) DIN EN ISO 1622-1:2012-05 43 Designation system3.1 GeneralThe designation system for thermoplastics is based on the following standardized pattern:DesignationIdentity blockDescription block (optional)International Standard number blockIndividual-item b

31、lockData block 1Data block 2Data block 3Data block 4Data block 5The designation consists of an optional description block, reading “Thermoplastics”, and an identity block comprising the International Standard number and an individual-item block. For unambiguous designation, the individual-item block

32、 is subdivided into five data blocks comprising the following information: Data block 1: Identification of the plastic by its abbreviated term (PS) in accordance with ISO 1043-1 (see 3.2). Data block 2: Position 1: Intended application or method of processing (see 3.3).Positions 2 to 8: Important pr

33、operties, additives and supplementary information (see 3.3). Data block 3: Designatory properties (see 3.4). Data block 4: Fillers or reinforcing materials and their nominal content (not included in this part of ISO 1622). Data block 5: For the purpose of specifications, a fifth data block may be ad

34、ded containing additional information (see 3.5).The first character of the individual-item block shall be a hyphen. The data blocks shall be separated from each other by commas.If a data block is not used, this shall be indicated by doubling the separation sign, i.e. by two commas ().3.2 Data block

35、1In this data block, after the hyphen, polystyrene plastics are identified by the abbreviated term “PS”, in accordance with ISO 1043-1.3.3 Data block 2In this data block, information about the intended application and/or method of processing is given in position 1 and information about important pro

36、perties, additives and colour in positions 2 to 8. The code-letters used are specified in Table 1.If information is presented in positions 2 to 8 and no specific information is given in position 1, the letter X shall be inserted in position 1.EN ISO 1622-1:2012 (E) DIN EN ISO 1622-1:2012-05 5 Table

37、1 Code-letters used in data block 2Code-letter Position 1 Code-letter Positions 2 to 8A Processing stabilizedC ColouredE Extrusion F Extrusion of films F Special burning characteristicsG General use L Light- and/or weather-stabilizedM Moulding N Natural (no colour added)R Mould release agentS Lubric

38、atedX No indication Z Antistatic3.4 Data block 33.4.1 GeneralIn this data block, the range of the Vicat softening temperature is represented by a three-figure code-number (see 3.4.2) and the range of the melt volume-flow rate by a two-figure code-number (see 3.4.3). The code-numbers are separated fr

39、om each other by hyphens.If a property value falls on or near a range limit, the manufacturer shall state which range will designate the material. If subsequent individual test values lie on, or on either side of, the limit because of manufacturing tolerances, the designation is not affected.3.4.2 V

40、icat softening temperatureThe Vicat softening temperature shall be determined in accordance with ISO 1622-2.The possible values of Vicat softening temperature are divided into four ranges, each represented by a three-figure code-number as specified in Table 2.Table 2 Range of Vicat softening tempera

41、ture in data block 3Code-numberRange of Vicat softening temperatureC075 80085 80 but 90095 90 but 100105 1003.4.3 Melt volume-flow rateThe melt volume-flow rate shall be determined in accordance with ISO 1622-2.The possible values of melt volume-flow rate are divided into four ranges, each represent

42、ed by a two-figure code-number as specified in Table 3.EN ISO 1622-1:2012 (E) DIN EN ISO 1622-1:2012-05 6Table 3 Range of melt volume-flow rate in data block 3Code-numberRange of melt volume-flow rate (MVR)cm3/10 min03 3,806 3,8 but 7,712 7,7 but 15,420 15,43.5 Data block 5Indication of additional r

43、equirements in this optional data block is a way of transforming the designation of a material into a specification for a particular application. This may be done, for example, by reference to a suitable national standard or to a standard-like, generally established specification.4 Example of a desi

44、gnationA polystyrene moulding and extrusion material (PS), intended for injection moulding (M), light- and/or weather-stabilized (L), natural (not coloured) (N), with a Vicat softening temperature of 84 C (085) and a melt volume-flow rate of 9,0 cm3/10 min (12), would be designated:Designation: Thermoplastics ISO 1622-PS,MLN,085-12EN ISO 1622-1:2012 (E) DIN EN ISO 1622-1:2012-05 7