DIN EN ISO 19063-1-2016 Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1 Designation system and basis for specifications (ISO 19063-1 2015) .pdf

1、May 2016 English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 83.080.20!%UVe“2505166www.din.deDIN

2、EN ISO 19063-1Plastics Impact-resistant polystyrene (PS-I) moulding and extrusion materials Part 1: Designation system and basis for specifications (ISO 19063-1:2015);English version EN ISO 19063-1:2015,English translation of DIN EN ISO 19063-1:2016-05Kunststoffe Schlagzhe Polystyrol (PS-I)-Formmass

3、en Teil 1: Bezeichnungssystem und Basis fr Spezifikationen (ISO 19063-1:2015);Englische Fassung EN ISO 19063-1:2015,Englische bersetzung von DIN EN ISO 19063-1:2016-05Plastiques Polystyrnes rsistants au choc (PS-I) pour moulage et extrusion Partie 1: Systme de dsignation et base de spcification (ISO

4、 19063-1:2015);Version anglaise EN ISO 19063-1:2015,Traduction anglaise de DIN EN ISO 19063-1:2016-05SupersedesDIN EN ISO 2897-1:1999-10www.beuth.deDocument comprises 16 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.05.16 DIN

5、 EN ISO 19063-1:2016-05 2 A comma is used as the decimal marker. National foreword This document (EN ISO 19063-1:2015) has been prepared by Technical Committee ISO/TC 61 “Plastics” in collaboration with Technical Committee ISO/TC 249 “Plastics” (Secretariat: NBN, Belgium). The responsible German bod

6、y involved in its preparation was DIN-Normenausschuss Kunststoffe (DIN Standards Committee Plastics), Working Committee NA 054-02-10 AA Thermoplast-Formmassen. Part 2 of this standard has been published as the following standard: DIN EN ISO 2897-2, Plastics Impact-resistant polystyrene (PS-I) mouldi

7、ng and extrusion materials Part 2: Preparation of test specimens and determination of properties The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 1043-1 DIN EN ISO 1043-1 ISO 1043-2 DIN EN ISO 1043-2 ISO 2897-2 DIN EN ISO 2897-2 Amendmen

8、ts This standard differs from DIN EN ISO 2897-1:1999-10 as follows: a) the number of the standard has been changed; b) the Introduction has been added; c) the data block system has been revised and brought more into line with ISO 1043 and ISO 11469. Previous editions DIN 16771-1: 1977-08, 1986-12 DI

9、N EN ISO 2897-1: 1999-10 DIN EN ISO 19063-1:2016-05 3 National Annex NA (informative) Bibliography DIN EN ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics DIN EN ISO 1043-2, Plastics Symbols and abbreviated terms Part 2: Fillers and reinforc

10、ing materials DIN EN ISO 2897-2, Plastics Impact-resistant polystyrene (PS-I) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties DIN EN ISO 19063-1:2016-05 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO

11、19063-1 December 2015 ICS 83.080.20 Supersedes EN ISO 2897-1:1999English Version Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 19063-1:2015) Plastiques - Polystyrnes rsistants au choc (PS-I) pour moulage

12、 et extrusion - Partie 1 : Systme de dsignation et base de spcification(ISO 19063-1:2015) Kunststoffe - Schlagzhe Polystyrol (PS-I)-Formmassen -Teil 1: Bezeichnungssystem und Basis fr Spezifikationen (ISO 19063-1:2015) This European Standard was approved by CEN on 26 September 2015. CEN members are

13、bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to th

14、e CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Cent

15、re has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuani

16、a, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-100

17、0 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 19063-1:2015 EEuropean foreword .3Introduction 51 Scope . 62 Normative references 63 Designation system 73.1 General . 73.2 Data block 1 . 73.3 Data block 2 . 73.4

18、 Data block 3 . 83.5 Data block 4 . 93.5.1 Vicat softening temperature 93.5.2 Melt mass-flow rate . 93.5.3 Charpy notched impact strength. 103.5.4 Flexural modulus 103.6 Data block 5 104 Examples of designations . 11Contents PageDIN EN ISO 19063-1:2016-05 EN ISO 19063-1:2015 (E)2Foreword . 4European

19、 foreword This document (EN ISO 19063-1:2015) has been prepared by Technical Committee ISO/TC 61 “Plastics“ in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publ

20、ication of an identical text or by endorsement, at the latest by June 2016, and conflicting national standards shall be withdrawn at the latest by June 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall

21、 not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 2897-1:1999. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bul

22、garia, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, T

23、urkey and the United Kingdom. Endorsement notice The text of ISO 19063-1:2015 has been approved by CEN as EN ISO 19063-1:2015 without any modification. DIN EN ISO 19063-1:2016-05 EN ISO 19063-1:2015 (E)3 ForewordISO (the International Organization for Standardization) is a worldwide federation of na

24、tional standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Intern

25、ational organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those inten

26、ded for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.

27、iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document wi

28、ll be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and express

29、ions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 9, Thermopl

30、astic materials.This first edition of ISO 19063-1 cancels and replaces ISO 2897-1:1997, which has been technically revised to introduce a new designation system.The revised designation system is published under a new ISO number, as many existing documents refer to ISO 2897-1. If the existing ISO 289

31、7-1 would be replaced by the new designation system, these documents would refer to the incorrect designation system.In order to give users time to switch from ISO 2897-1 to ISO 19063-1, any designation system according to ISO 2897-1 is to be phased out in 5 to 10 years. During this period, ISO 2897

32、-2 will effectively be Part 2 of this International Standard.ISO 19063 consists of the following parts, under the general title Plastics Impact-resistant polystyrene (PS-I) moulding and extrusion materials: Part 1: Designation system and basis for specificationsDIN EN ISO 19063-1:2016-05 EN ISO 1906

33、3-1:2015 (E)4 IntroductionISO 2897-1 is complex and does not fit with daily practice anymore. In practice, ISO 1043 (all parts) and ISO 11469 are, in combination, “improperly” being used as a designation system for, e.g. marking. The aim of this International Standard is to simplify the data block s

34、ystem and to connect more to ISO 1043 (all parts) and ISO 11469, where the first two blocks are used for generic identification and marking of products.DIN EN ISO 19063-1:2016-05 EN ISO 19063-1:2015 (E)5 1 ScopeThis part of ISO 19063 establishes a system of designation for impact-resistant polystyre

35、ne (PS-I) moulding and extrusion materials, which may be used as the basis for specifications.The types of impact-resistant polystyrene plastic are differentiated from each other by a classification system based on appropriate levels of the designatory properties:a) Vicat softening temperature;b) me

36、lt mass-flow rate;c) Charpy notched impact strength;d) flexural modulus;and on information about composition, intended application and/or method of processing, important properties, additives, colorants, fillers, and reinforcing materials.This part of ISO 19063 is applicable to all impact-resistant

37、polystyrene plastics with a two-phase polymer system comprised of a continuous phase, consisting of polystyrene and/or a copolymer of styrene with an alkyl-substituted styrene, and a dispersed elastomeric phase based on butadiene.It applies to materials ready for normal use, unmodified or modified b

38、y colorants, additives, fillers, etc.This part of ISO 19063 does not apply to expandable materials.It is not intended to imply that materials having the same designation give necessarily the same performance. This part of ISO 19063 does not provide engineering data, performance data, or data on proc

39、essing conditions which may be required to specify a material for a particular application and/or method of processing.If such additional properties are required, they will be determined in accordance with the test methods specified in ISO 2897-2, if suitable.In order to specify a thermoplastic mate

40、rial for a particular application or to ensure reproducible processing, additional requirements may be given in data block 5 (see 3.1).2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated

41、references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristicsISO 1043-2, Plastics Symbols and abbreviated

42、 terms Part 2: Fillers and reinforcing materialsDIN EN ISO 19063-1:2016-05 EN ISO 19063-1:2015 (E)6 ISO 2897-2, Plastics Impact-resistant polystyrene (PS-I) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties3 Designation system3.1 GeneralThe design

43、ation system for thermoplastics is based on the following standardized pattern:DesignationDescription block (optional)Identity blockInternational Standard number blockIndividual-item blockData block 1Data block 2Data block 3Data block 4Data block 5The designation consists of an optional description

44、block, reading “Thermoplastics”, and an identity block comprising the International Standard number and an individual-item block. For unambiguous designation, the individual-item block is subdivided into five data blocks comprising the following information: Data block 1: Identification of the plast

45、ic by its abbreviated term (PS-I) in accordance with ISO 1043-1 (see 3.2); Data block 2: Fillers or reinforcing materials and their nominal content (see 3.3); Data block 3: First letter: Intended application and/or method of processing (see 3.4).Letters 2 to 8: Important properties, additives, and s

46、upplementary information (see 3.4); Data block 4: Designatory properties (see 3.5); Data block 5: For the purpose of specifications, a fifth data block may be added containing addi-tional information (see 3.6).The first character of the individual-item block shall be a hyphen. The data blocks shall

47、be separated from each other by commas.If a data block is not used, this shall be indicated by doubling the separation sign, i.e. by two commas (,).3.2 Data block 1In this data block, after the hyphen, impact-resistant polystyrene plastics are identified by its abbreviated term, PS-I, in accordance

48、with ISO 1043-1.3.3 Data block 2In this data block, the type of filler and/or reinforcing material is represented by a single code-letter in position 1 and its physical form by a second code-letter in position 2, the code-letters being as specified in Table 1 (in accordance with ISO 1043-2). For the filler material of metal, it is represented by a two-code-letter in position 1. Subsequently (without a space), the mass