DIN EN ISO 4016-2011 Hexagon head bolts - Product grade C (ISO 4016 2011) German version EN ISO 4016 2011《六角头螺栓 C级产品(ISO 4016-2011) 德文版本EN ISO 4016-2011》.pdf

1、June 2011 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 2

2、1.060.10!$s)n“1800675www.din.deDDIN EN ISO 4016Hexagon head bolts Product grade C (ISO 4016:2011)English translation of DIN EN ISO 4016:2011-06Sechskantschrauben mit Schaft Produktklasse C (ISO 4016:2011)Englische bersetzung von DIN EN ISO 4016:2011-06Vis tte hexagonale partiellement filetes Grade C

3、 (ISO 4016:2011)Traduction anglaise de DIN EN ISO 4016:2011-06SupersedesDIN EN ISO 4016:2001-03www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.1706.11 DIN EN ISO 4016:2011-06 2 A comma is used as the decimal marker. National forewo

4、rd This standard has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Fasteners” (both secretariats are held by DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Mechanische Verbindungselement

5、e (Fasteners Standards Committee), Working Committee NA 067-00-02 AA Verbindungs-elemente mit metrischem Auengewinde. The DIN 4000-160-1 tabular layout of article characteristics shall apply to screws covered in this standard. The DIN Standards corresponding to the International Standards referred t

6、o in this document are as follows: ISO 225 DIN EN ISO 225 ISO 724 DIN ISO 724 ISO 898-1 DIN EN ISO 898-1 ISO 965-1 DIN ISO 965-1 ISO 3269 DIN EN ISO 3269 ISO 4018 DIN EN ISO 4018 ISO 4042 DIN EN ISO 4042 ISO 4759-1 DIN EN ISO 4759-1 ISO 8992 DIN ISO 8992 ISO 10683 DIN EN ISO 10683 Amendments This st

7、andard differs from DIN EN ISO 4016:2001-03 as follows: a) normative references are now undated; b) the standard has been editorially revised and normative references have been updated; c) Annex ZA has been deleted. Previous editions DIN 556: 1923-02, 1925-04, 1936-04 DIN 601: 1925-07, 1934-07, 1967

8、-12, 1970-11, 1983-12, 1984-06, 1987-09 DIN 602: 1925-07, 1936-07 DIN 556 Supplement: 1926-10 DIN 601-1: 1941-01, 1951-09, 1963-03 DIN 601-1 Supplement 1: 1942-11 DIN ISO 4016: 1987-09, 1989-10 DIN EN 24016: 1992-02 DIN EN ISO 4016: 2001-03 DIN EN ISO 4016:2011-06 3 National Annex NA (informative) B

9、ibliography DIN 4000-160, Tabular layout of product properties Part 160: Fasteners with external thread DIN EN ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and designations of dimensions DIN EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bol

10、ts, screws and studs with specified property classes Coarse thread and fine pitch thread DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 4018, Hexagon head screws Product grade C DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts,

11、screws, studs and nuts Product grades A, B and C DIN EN ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings DIN ISO 724, ISO general purpose metric screw threads Basic dimensions DIN ISO 965-1, ISO general purpose metric screw threads Tolerances Part 1: Principles and basic data DI

12、N ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts DIN EN ISO 4016:2011-06 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 4016 March 2011 ICS 21.060.10 Supersedes EN ISO 4016:2000English Version Hexagon head bolts - Product grade

13、 C (ISO 4016:2011) Vis tte hexagonale partiellement filetes - Grade C (ISO 4016:2011) Sechskantschrauben mit Schaft - Produktklasse C (ISO 4016:2011) This European Standard was approved by CEN on 31 January 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipula

14、te the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Sta

15、ndard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the na

16、tional standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switz

17、erland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No.

18、EN ISO 4016:2011: EContents Page Foreword3 Introduction .4 1 Scope 5 2 Normative references 5 3 Dimensions.5 4 Specifications and reference International Standards 11 5 Designation 11 Bibliography 12 EN ISO 4016:2011 (E) DIN EN ISO 4016:2011-06 2 Foreword This document (EN ISO 4016:2011) has been pr

19、epared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the l

20、atest by September 2011, and conflicting national standards shall be withdrawn at the latest by September 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any o

21、r all such patent rights. This document supersedes EN ISO 4016:2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark,

22、 Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 4016:2011 has been approved by

23、 CEN as a EN ISO 4016:2011 without any modification. EN ISO 4016:2011 (E) DIN EN ISO 4016:2011-06 3 Introduction This International Standard belongs to a complete group of product standards developed by ISO on external hexagon drive fasteners. It comprises the following: a) hexagon head bolts (ISO 4

24、014, ISO 4015, ISO 4016 and ISO 8765); b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676); c) hexagon nuts (ISO 4032, ISO 4033, ISO 4034, ISO 4035, ISO 4036, ISO 7040, ISO 7041, ISO 7042, ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 and ISO 10513); d) hexagon bolts wi

25、th flange (ISO 4162, ISO 15071 and ISO 15072); e) hexagon nuts with flange (ISO 4161, ISO 7043, ISO 7044, ISO 10663, ISO 12125, ISO 12126 and ISO 21670). EN ISO 4016:2011 (E) DIN EN ISO 4016:2011-06 4 1 Scope This International Standard specifies the characteristics of hexagon head bolts with thread

26、s from M5 up to and including M64, of product grade C. If, in special cases, specifications other than those listed in this International Standard are required, they can be selected from existing International Standards, for example ISO 724, ISO 888, ISO 898-1, ISO 965-1 and ISO 4759-1. 2 Normative

27、references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, stud

28、s and nuts Symbols and descriptions of dimensions ISO 724, ISO general-purpose metric screw threads Basic dimensions ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread

29、ISO 965-1, ISO general-purpose metric screw threads Tolerances Part 1: Principles and basic data ISO 3269, Fasteners Acceptance inspection ISO 4018, Hexagon head screws Product grade C ISO 4042, Fasteners Electroplated coatings ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nu

30、ts Product grades A, B and C ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings 3 Dimensions See Figure 1 and Tables 1 and 2. Symbols and descriptions of dimensions are specified in ISO 225. EN ISO 4016:201

31、1 (E) DIN EN ISO 4016:2011-06 5 Dimensions in millimetres a = 15 to 30. b End without special requirements. c Incomplete thread u u 2P. d Reference datum for dw. eWasher face permissible. Figure 1 EN ISO 4016:2011 (E) DIN EN ISO 4016:2011-06 6 Table 1 Preferred threads Dimensions in millimetres Thre

32、ad, d M5 M6 M8 M10 M12 M16 M20 Pa0,8 1 1,25 1,5 1,75 2 2,5 b16 18 22 26 30 38 46 c22 24 28 32 36 44 52 b ref. d35 37 41 45 49 57 65 c max. 0,5 0,5 0,6 0,6 0,6 0,8 0,8 damax. 6 7,2 10,2 12,2 14,7 18,7 24,4 max. 5,48 6,48 8,58 10,58 12,7 16,7 20,84 dsmin. 4,52 5,52 7,42 9,42 11,3 15,3 19,16 dwmin. 6,7

33、4 8,74 11,47 14,47 16,47 22 27,7 e min. 8,63 10,89 14,2 17,59 19,85 26,17 32,95 nom. 3,5 4 5,3 6,4 7,5 10 12,5 max. 3,875 4,375 5,675 6,85 7,95 10,75 13,4 k min. 3,125 3,625 4,925 5,95 7,05 9,25 11,6 kwemin. 2,19 2,54 3,45 4,17 4,94 6,48 8,12 r min. 0,2 0,25 0,4 0,4 0,6 0,6 0,8 nom. = max. 8,00 10,0

34、0 13,00 16,00 18,00 24,00 30,00 s min. 7,64 9,64 12,57 15,57 17,57 23,16 29,16 l lsand lgflslglslglslglslglslglslglslgnom. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.25 23,95 26,05 5 9 30 28,95 31,05 10 14 7 12 35 33,75 36,25 15 19 12 17 For sizes above the solid,

35、 bold, stepped line, ISO 4018 is recommended. 40 38,75 41,25 20 24 17 22 11,75 18 45 43,75 46,25 25 29 22 27 16,75 23 11,5 19 50 48,75 51,25 30 34 27 32 21,75 28 16,5 24 55 53,5 56,5 32 37 26,75 33 21,5 29 16,25 25 60 58,5 61,5 37 42 31,75 38 26,5 34 21,25 30 65 63,5 66,5 36,75 43 31,5 39 26,25 35 1

36、7 27 70 68,5 71,5 41,75 48 36,5 44 31,25 40 22 32 80 78,5 81,5 51,75 58 46,5 54 41,25 50 32 42 21,5 34 90 88,25 91,75 56,5 64 51,25 60 42 52 31,5 44 100 98,25 101,75 66,5 74 61,25 70 52 62 41,5 54 110 108,25 111,75 71,25 80 62 72 51,5 64 120 118,25 121,75 81,25 90 72 82 61,5 74 130 128 132 76 86 65,

37、5 78 140 138 142 86 96 75,5 88 150 148 152 96 106 85,5 98 160 156 164 106 116 95,5 108 180 176 184 115,5 128 200 195,4 204,6 135,5 148 220 215,4 224,6 240 235,4 244,6 260 254,8 265,2 280 274,8 285,2 300 294,8 305,2 320 314,3 325,7 340 334,3 345,7 360 354,3 365,7 380 374,3 385,7 400 394,3 405,7 420 4

38、13,7 426,3 440 433,7 446,3 460 453,7 466,3 480 473,7 486,3 500 493,7 506,3 EN ISO 4016:2011 (E) DIN EN ISO 4016:2011-06 7 Table 1 (continued) Dimensions in millimetres Thread, d M24 M30 M36 M42 M48 M56 M64 Pa3 3,5 4 4,5 5 5,5 6 b 54 66 c 60 72 84 96 108 b ref. d 73 85 97 109 121 137 153 c max. 0,8 0

39、,8 0,8 1 1 1 1 damax. 28,4 35,4 42,4 48,6 56,6 67 75 max. 24,84 30,84 37 43 49 57,2 65,2 dsmin. 23,16 29,16 35 41 47 54,8 62,8 dwmin. 33,25 42,75 51,11 59,95 69,45 78,66 88,16 e min. 39,55 50,85 60,79 71,3 82,6 93,56 104,86 nom. 15 18,7 22,5 26 30 35 40 max. 15,9 19,75 23,55 27,05 31,05 36,25 41,25

40、k min. 14,1 17,65 21,45 24,95 28,95 33,75 38,75 kwemin. 9,87 12,36 15,02 17,47 20,27 23,63 27,13 r min. 0,8 1 1 1,2 1,6 2 2 nom. = max. 36 46 55,0 65,0 75,0 85,0 95,0 s min. 35 45 53,8 63,1 73,1 82,8 92,8 l lsand lgflslglslglslglslglslglslglslgnom. min. max. min. max. min. max. min. max. min. max. m

41、in. max. min. max. min. max.25 23,95 26,05 30 28,95 31,05 For sizes above the solid, bold, stepped line, ISO 4018 is recommended. 35 33,75 36,25 40 38,75 41,25 45 43,75 46,25 50 48,75 51,25 55 53,5 56,5 60 58,5 61,5 65 63,5 6,5 70 68,5 71,5 80 78,5 81,5 90 88,25 91,75 100 98,25 101,75 31 46 110 108,

42、25 111,75 41 56 120 118,25 121,75 51 66 36,5 54 130 128 132 55 70 40,5 58 140 138 142 65 80 50,5 68 36 56 150 148 152 75 90 60,5 78 46 66 160 156 164 85 100 70,5 88 56 76 180 176 184 105 120 90,5 108 76 96 61,5 84 200 195,4 204,6 125 140 110,5 128 96 116 81,5 104 67 92 220 215,4 224,6 132 147 117,5

43、135 103 123 88,5 111 74 99 240 235,4 244,6 152 167 137,5 155 123 143 108,5 131 94 119 75,5 103 260 254,8 265,2 157,5 175 143 163 128,5 151 114 139 95,5 123 77 107 280 274,8 285,2 177,5 195 163 183 148,5 171 134 159 115,5 143 97 127 300 294,8 305,2 197,5 215 183 203 168,5 191 154 179 135,5 163 117 14

44、7 320 314,3 325,7 203 223 188,5 211 174 199 155,5 183 137 167 340 334,3 345,7 223 243 208,5 231 194 219 175,5 203 157 187 360 354,3 365,7 243 263 228,5 251 214 239 195,5 223 177 207 380 374,3 385,7 248,5 271 234 259 215,5 243 197 227 400 394,3 405,7 268,5 291 254 279 235,5 263 217 247 420 413,7 426,

45、3 288,5 311 274 299 255,5 283 237 267 440 433,7 446,3 294 319 275,5 303 257 287 460 453,7 466,3 314 339 295,5 323 277 307 480 473,7 486,3 334 359 315,5 343 297 327 500 493,7 506,3 335,5 363 317 347 NOTE Preferred lengths are defined in terms of lsand lg. aP is the pitch of the thread. bFor lnomu 125

46、 mm. cFor 125 mm 200 mm. ekw,min= 0,7 kmin. flg,max= lnom b. ls,min= lg,max 5 P. EN ISO 4016:2011 (E) DIN EN ISO 4016:2011-06 8 Table 2 Non-preferred threads Dimensions in millimetres Thread, d M14 M18 M22 M27 M33 Pa2 2,5 2,5 3 3,5 b 34 42 50 60 c 40 48 56 66 78 b ref. d 53 61 69 79 91 c max. 0,6 0,

47、8 0,8 0,8 0,8 damax. 16,7 21,2 26,4 32,4 38,4 max. 14,7 18,7 22,84 27,84 34 dsmin. 13,3 17,3 21,16 26,16 32 dwmin. 19,15 24,85 31,35 38 46,55 e min. 22,78 29,56 37,29 45,2 55,37 nom. 8,8 11,5 14 17 21 max. 9,25 12,4 14,9 17,9 22,05 k min. 8,35 10,6 13,1 16,1 19,95 kwemin. 5,85 7,42 9,17 11,27 13,97

48、r min. 0,6 0,6 0,8 1 1 nom. = max. 21,00 27,00 34 41 50 s min. 20,16 26,16 33 40 49 l lsand lgflslglslglslglslglslgnom. min. max. min. max. min. max. min. max. min. max. min. max. 60 58,5 61,5 16 26 65 63,5 66,5 21 31 70 68,5 71,5 26 36 For sizes above the solid, bold, stepped line, ISO 4018 is recommended. 80 78,5 81,5 36 46 25,5 38 90 88,25 91,75 46 56 35,5 48 27,5 40 100 98,25 101,75 56 66 45,5 58 37,5 50 110 108,25 111,75 66 76