DIN EN ISO 61-2000 Plastics - Determination of apparent density of moulding material that cannot be poured from a specified funnel (ISO 61 1976) German version EN ISO 61 1999《塑料 不能.pdf

1、DEUTSCHE NORM Januarv 2000 I DIN material that cannot be poured from a specified funnel Plastics - Determination of apparent density of moulding - I EN IS061 (IS 61 : 1976) English version of DIN EN IS0 61 ICs 83.080.01 Kunststoffe - Bestimmung der scheinbaren Dichte von Formmassen, die nicht durch

2、einen genormten Trichter abflieen knnen (Stopfdichte) (IS0 61 : 1976) Supersedes parts of DIN 53466, February 1984 edition. European Standard EN IS0 61 : 1999 has the status of a DIN Standard. A comma is used as the decimal marker. National foreword This standard has been published in accordance wit

3、h a decision taken by CEN/TC 249 to adopt, without alteration, International Standard IS0 61 as a European Standard. The responsible German body involved in its preparation was the Normenausschuss Kunststoffe (Plastics Standards Committee), Technical Committee Rieselfahige Duroplaste und langfaserve

4、rst2rkte Kunststoffe. Amendments Parts of DIN 53466, February 1984 edition, have been superseded by the specifications of EN IS0 61 which is identical to IS0 61. Previous editions DIN 53466: 1960-1 1, 1984-02; DIN 53467: 1960-1 1; DIN 53468: 1951-06, 1960-11, 1974-12. EN comprises 3 pages. No pari o

5、f this standard may be reproduced without the prior permission of Ref. No. DIN EN IS0 61 : 2000-0 V Deutsches Institut fr Nonung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, s the exclusive right of sale for German Standards (DIN-Nonen). English price group 05 Sales No. 1105 07.00 COPYRI

6、GHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesCOPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 61 June 1999 ICs 83.080.1 O English version Plastic

7、s Determination of apparent density of moulding material that cannot be poured from a specified funnel (IS0 61 : 1976) Matires plastiques - Dtermination de la masse volumique apparente des matires mouler non suscepti- bles de s?couleur travers un entonnoir donn (IS0 61 : 1976) Kunststoffe - Bestimmu

8、ng der scheinbaren Dichte von Formmassen, die nicht durch einen genormten Trichter abflieen knnen (Stopf- dichte) (IS0 61 : 1976) This European Standard was approved by CEN on 1999-04-06. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for givi

9、ng this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three official versio

10、ns (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, th

11、e Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Se

12、cretariat: rue de Stassart 36, B-1050 Brussels O 1999. CEN - All rights of exploitation in any form and by any means reserved worldwide for CEN national members. Ref. No. EN IS0 61 : 1999 E COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling ServicesPage 2 EN I

13、S0 61 : 1999 Foreword International Standard IS0 61 : 1976 Plastics - Determination of apparent density of moulding material that cannot be poured from a specified funnel, which was prepared by ISO/TC 61 Plastics of the International Organization for Standardization, has been adopted by Technical Co

14、mmittee CEN/TC 249 Plastics, the Secretariat of which is held by IBN, as a European Standard. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, and conflicting national standards withdrawn, by December 1999 at the l

15、atest. In accordance with the CENKENELEC Internal Regulations, the national standards organizations of the follow- ing countries are bound to implement this European Standard: Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Ne

16、therlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. Endorsement notice The text of the International Standard IS0 61 : 1976 was approved by CEN as a European Standard without any modification. COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Informat

17、ion Handling ServicesPage 3 EN IS0 61 : 1999 1 This International Standard specifies a method of determi- ning the apparent density, .e. the mass per unit of volume, of loose moulding material that cannot be poured from a funnel of specified design. NOTE - For a method of determining the apparent de

18、nsity of loose moulding material that can be poured from a specified funnel, see IS0 60. A knowledge of apparent density is of limited value in estimating the relative fluffiness or bulk of moulding materials, unless their densities in the moulded condition are approximately the same. SCOPE AND FIEL

19、D OF APPLICATION 2 APPARATUS 2.1 Balance, accurate to 0,l g. 2.2 Measuring cylinder, smoothly finished inside, which may be constructed of metal, of capacity 1 O00 * 20 ml and internal diameter 90 I2 mm. 2.3 Plunger, consisting of a hollow cylinder of mass 2300k 20g, closed at one end and having an

20、external diameter slightly smaller than the internal diameter of the measuring cylinder. The plunger may conveniently be weighted with lead shot. 3 PROCEDURE 3.1 Drop 60 f 0.2 g of loose moulding material, little by little, into the measuring cylinder (2.2) so that it is distrib- uted evenly with it

21、s surface as level as possible. Lower the plunger (2.3) slowly into the measuring cylinder until it is entirely supported by the material. After 1 min, measure the height of the material, with the plunger resting upon it, to the nearest 1 mm. A convenient method of measuring the height of the materi

22、al is, for example, by means of a suitable scale marked vertically on the outside surface of the plunger. 3.2 Make three determinations on the sample of moulding material under test. 4 EXPRESSION OF RESULTS The apparent density of the moulding material under test is given, in grams per millilitre (s

23、ee note) by the formula m Ah where m is the mass, in grams, of the material placed in the measuring cylinder (.e. 60); A is the internal cross-sectional area of the measuring cylinder, in square centimetres; h is the height of moulding material in the measuring cylinder, in centimetres. NOTE - Altho

24、ugh apparent density is calculated in grams per cubic centimetre, it is expressed here in grams per millilitre for the sake of uniformity with iSO60. No adjustment of the test result is required. Take as the result the arithmetic mean of the results of the three determinations. 5 TESTREPORT The test report shall include the following particulars : a) complete identification of the material tested; b) the individual results and the mean. COPYRIGHT DIN DEUTSCHES Institut Fur Normung E.V.- EnglishLicensed by Information Handling Services