1、July 2011 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 2
2、1.060.10!$sP“1804559www.din.deDDIN EN ISO 8676Hexagon head screws with metric fine pitch thread Product grades A and B (ISO 8676:2011)English translation of DIN EN ISO 8676:2011-07Sechskantschrauben mit Gewinde bis Kopf und metrischem Feingewinde Produktklassen A und B (ISO 8676:2011)Englische berse
3、tzung von DIN EN ISO 8676:2011-07Vis tte hexagonale filetage mtrique pas fin entirement filetes Grades A et B (ISO 8676:2011)Traduction anglaise de DIN EN ISO 8676:2011-07SupersedesDIN EN ISO 8676:2001-03www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be cons
4、idered authoritative.1906.11 DIN EN ISO 8676:2011-07 National foreword This standard has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Fasteners” (both secretariats are held by DIN, Germany). The responsible German body involved in it
5、s preparation was the Normenausschuss Mechanische Verbindungselemente (Fasteners Standards Committee), Working Committee NA 067-00-02 AA Verbindungs-elemente mit metrischem Auengewinde. The DIN 4000-160-1 tabular layout of article characteristics shall apply to screws covered in this standard. The D
6、IN Standards corresponding to the International Standards referred to in Clause 2 of this document are as follows: ISO 225 DIN EN ISO 225 ISO 724 DIN ISO 724 ISO 898-1 DIN EN ISO 898-1 ISO 965-1 DIN ISO 965-1 ISO 3269 DIN EN ISO 3269 ISO 3506-1 DIN EN ISO 3506-1 ISO 4042 DIN EN ISO 4042 ISO 4753 DIN
7、 EN ISO 4753 ISO 4759-1 DIN EN ISO 4759-1 ISO 6157-1 DIN EN 26157-1 ISO 8839 DIN EN 28839 ISO 8992 DIN ISO 8992 ISO 10683 DIN EN ISO 10683 Amendments This standard differs from DIN EN ISO 8676:2001-03 as follows: a) normative references are now undated; b) the standard has been editorially revised a
8、nd normative references have been updated; c) Annex ZA has been deleted. Previous editions DIN 961: 1952-12, 1963-03, 1967-11, 1970-11, 1983-12, 1990-01 DIN ISO 8676: 1990-01 DIN EN 28676: 1992-02 DIN EN ISO 8676: 2001-03 2 A comma is used as the decimal marker. DIN EN ISO 8676:2011-07 National Anne
9、x NA (informative) Bibliography DIN 4000-160, Tabular layout of product properties Part 160: Fasteners with external thread DIN EN 26157-1, Fasteners Surface discontinuities Bolts, screws and studs subject to general requirements DIN EN 28839, Mechanical properties of fasteners Nonferrous metal bolt
10、s, screws, studs and nuts DIN EN ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions DIN EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pi
11、tch thread DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 4753, Fasteners Ends of parts with external ISO metric th
12、read DIN EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C DIN EN ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings DIN ISO 724, ISO general purpose metric screw threads Basic dimensions DIN ISO 965-1, ISO general purpose metr
13、ic screw threads Tolerances Part 1: Principles and basic data DIN ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts 3 DIN EN ISO 8676:2011-07 This page is intentionally blank 4 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 8676 April 2011 ICS 21.060.10 Supersedes
14、EN ISO 8676:2000English Version Hexagon head screws with metric fine pitch thread Product grades A and B (ISO 8676:2011) Vis tte hexagonale filetage mtrique pas fin entirement filetes Grades A et B (ISO 8676:2011) Sechskantschrauben mit Gewinde bis Kopf und metrischem Feingewinde Produktklassen A un
15、d B (ISO 8676:2011) This European Standard was approved by CEN on 31 January 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and
16、bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the re
17、sponsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany,
18、 Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Mana
19、gement Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 8676:2011: EContents Page Foreword .3 Introduction.4 1 Scope.5 2 Normative references 5 3 Dimensions .6 4 Specifications and
20、reference International Standards.13 5 Designation.13 Bibliography14 EN ISO 8676:2011 (E) DIN EN ISO 8676:2011-07 2Foreword This document (EN ISO 8676:2011) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat
21、of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at the latest by October 2011. Attention is drawn to th
22、e possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 8676:2000. According to the CEN/CENELEC Internal Regulations, the national sta
23、ndards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
24、 Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 8676:2011 has been approved by CEN as a EN ISO 8676:2011 without any modification. EN ISO 8676:2011 (E) DIN EN ISO 8676:2011-07 3Introduction This International Stand
25、ard belongs to a complete group of product standards developed by ISO on external hexagon drive fasteners. It comprises the following: a) hexagon head bolts (ISO 4014, ISO 4015, ISO 4016 and ISO 8765); b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676); c) hexagon nuts (ISO 4032, ISO 4033, ISO
26、 4034, ISO 4035, ISO 4036, ISO 7040, ISO 7041, ISO 7042, ISO 7719, ISO 7720, ISO 8673, ISO 8674, ISO 8675, ISO 10511, ISO 10512 and ISO 10513); d) hexagon bolts with flange (ISO 4162, ISO 15071 and ISO 15072); e) hexagon nuts with flange (ISO 4161, ISO 7043, ISO 7044, ISO 10663, ISO 12125, ISO 12126
27、 and ISO 21670). EN ISO 8676:2011 (E) DIN EN ISO 8676:2011-07 41 Scope This International Standard specifies the characteristics of hexagon head screws with metric fine pitch thread with nominal thread diameters, d, from 8 mm to 64 mm, of product grade A for nominal thread diameters, d, from 8 mm to
28、 24 mm and nominal lengths, l, up to and including 10d or 150 mm, whichever is the shorter, and of product grade B for nominal thread diameters, d, over 24 mm or nominal lengths, l, over 10d or 150 mm, whichever is the shorter. If, in special cases, specifications other than those listed in this Int
29、ernational Standard are required, they can be selected from existing International Standards, for example ISO 724, ISO 888, ISO 898-1, ISO 965-1, ISO 3506-1, ISO 4753 and ISO 4759-1. It is intended that coarse thread screws according to ISO 4017 be the first choice. 2 Normative references The follow
30、ing referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, studs and nuts Symbols an
31、d descriptions of dimensions ISO 724, ISO general-purpose metric screw threads Basic dimensions ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread ISO 965-1, ISO genera
32、l-purpose metric screw threads Tolerances Part 1: Principles and basic data ISO 3269, Fasteners Acceptance inspection ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs ISO 4042, Fasteners Electroplated coatings ISO 4753, Fasteners Ends
33、 of parts with external ISO metric thread ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C ISO 6157-1, Fasteners Surface discontinuities Part 1: Bolts, screws and studs for general requirements ISO 8839, Mechanical properties of fasteners Bolts, sc
34、rews, studs and nuts made of non-ferrous metals ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings EN ISO 8676:2011 (E) DIN EN ISO 8676:2011-07 53 Dimensions See Figure 1 and Tables 1 and 2. Symbols and des
35、criptions of dimensions are specified in ISO 225. Dimensions in millimetres a = 15 to 30. b The point shall be chamfered in accordance with ISO 4753. c Incomplete thread u u 2P. d Reference datum for dw. eds pitch diameter. f Permissible shape. Figure 1 EN ISO 8676:2011 (E) DIN EN ISO 8676:2011-07 6
36、Table 1 Preferred threads Dimensions inmillimetres Thread(d P)M8 1 M10 1M121,5M161,5M201,5M24 2 M30 2M36 3M42 3M48 3M56 4M64 4 max.3 3 4,5 4,5 4,5 6 6 9 9 9 12 12 amin. 1 1 1,5 1,5 1,5 2 2 3 3 3 4 4 max.0,60 0,60 0,60 0,8 0,8 0,8 0,8 0,8 1,0 1,0 1,0 1,0 c min. 0,15 0,15 0,15 0,2 0,2 0,2 0,2 0,2 0,3
37、0,3 0,3 0,3 damax.9,2 11,2 13,7 17,7 22,4 26,4 33,4 39,4 45,6 52,6 63 71 A 11,63 14,63 16,63 22,49 28,19 33,61 dwProduct gradeB min. 11,47 14,47 16,47 22 27,7 33,25 42,75 51,11 59,95 69,45 78,66 88,16 A 14,38 17,77 20,03 26,75 33,53 39,98 eProduct gradeB min. 14,20 17,59 19,85 26,17 32,95 39,55 50,8
38、5 60,79 71,3 82,6 93,56 104,86nom. 5,3 6,4 7,5 10 12,5 15 18,7 22,5 26 30 35 40 max.5,45 6,58 7,68 10,18 12,715 15,215 Product grade A min. 5,15 6,22 7,32 9,82 12,285 14,785 max.5,54 6,69 7,79 10,29 12,85 15,35 19,12 22,92 26,42 30,42 35,5 40,5 kProduct grade B min. 5,06 6,11 7,21 9,71 12,15 14,65 1
39、8,28 22,08 25,58 29,58 34,5 39,5 A 3,61 4,35 5,12 6,87 8,6 10,35 kwaProduct gradeB min. 3,54 4,28 5,05 6,8 8,51 10,26 12,8 15,46 17,91 20,71 24,15 27,65 rmin. 0,4 0,4 0,6 0,6 0,8 0,8 1 1 1,2 1,6 2 2 nom. =max. 13,00 16,00 18,00 24,00 30,00 36,00 46 55,0 65,0 75,0 85,0 95,0 A 12,73 15,73 17,73 23,67
40、29,67 35,38 sProduct gradeB min. 12,57 15,57 17,57 23,16 29,16 35 45 53,8 63,1 73,1 82,8 92,8 EN ISO 8676:2011 (E) DIN EN ISO 8676:2011-07 7Table 1 (continued)Dimensions inmillimetres Thread(d P)M8 1 M10 1M121,5M161,5M201,5M24 2 M30 2M36 3M42 3M48 3M56 4M64 4 Product gradeA B lbnom. min. max.min. ma
41、x.16 15,65 16,35 20 19,58 20,42 25 24,58 25,42 30 29,58 30,42 35 34,5 35,5 40 39,5 40,5 38,75 41,25 45 44,5 45,5 43,75 46,25 50 49,5 50,5 48,75 51,25 55 54,4 55,6 53,5 56,5 60 59,4 60,6 58,5 61,5 65 64,4 65,6 63,5 66,5 70 69,4 70,6 68,5 71,5 80 79,4 80,6 78,5 81,5 90 89,3 90,7 88,25 91,75 100 99,3 1
42、00,7 98,25 101,75110 109,3 110,7 108,25111,75120 119,3 120,7 118,25121,75130 129,2 130,8 128 132 140 139,2 140,8 138 142 150 149,2 150,8 148 152 160 158 162 180 178 182 200 197,7 202,3 220 217,7 222,3 EN ISO 8676:2011 (E) DIN EN ISO 8676:2011-07 8Table 1 (continued)Dimensions inmillimetres Thread(d
43、P)M8 1 M10 1M121,5M161,5M201,5M24 2 M30 2M36 3M42 3M48 3M56 4M64 4 Product gradeA B lbnom. min. max.min. max.240 237,7 242,3 260 257,4 262,6 280 277,4 282,6 300 297,4 302,6 320 317,15322,85340 337,15342,85360 357,15362,85380 377,15382,85400 397,15402,85420 416,85423,15440 436,85443,15460 456,85463,1
44、5480 476,85483,15500 496,85503,15akw,min=0,7 kmin. bRange of preferred lengths between the solid, bold, stepped lines: for product grade A, above the discontinuous, stepped line; for product grade B, belowthisstepped line.EN ISO 8676:2011 (E) DIN EN ISO 8676:2011-07 9Table 2 Non-preferredthreads Dim
45、ensions inmillimetres Thread(dP)M101,25M121,25M14 1,5M18 1,5M20 2 M22 1,5 M27 2 M33 2 M39 3 M45 3 M52 4 M60 4 max. 4 4 4,5 4,5 6 4,5 6 6 9 9 12 12 amin. 1,25 1,25 1,5 1,5 2 1,5 2 2 3 3 4 4 max. 0,600,60 0,60 0,8 0,8 0,8 0,8 0,8 1,0 1,0 1,0 1,0 c min. 0,15 0,15 0,15 0,2 0,2 0,2 0,2 0,2 0,3 0,3 0,3 0,
46、3 damax. 11,2 13,7 15,7 20,2 22,4 24,4 30,4 36,4 42,4 48,6 56,6 67 A 14,63 16,63 19,64 25,34 28,19 31,71 dwProduct gradeB min. 14,47 16,47 19,15 24,85 27,7 31,35 38 46,55 55,86 64,7 74,2 83,41 A 17,77 20,03 23,36 30,14 33,53 37,72 eProduct gradeB min. 17,59 19,85 22,78 29,56 32,95 37,29 45,2 55,37 6
47、6,44 76,95 88,25 99,21 nom. 6,4 7,5 8,8 11,5 12,5 14 17 21 25 28 33 38 max. 6,58 7,68 8,98 11,715 12,715 14,215 Product grade A min. 6,22 7,32 8,62 11,285 12,285 13,785 max. 6,69 7,79 9,09 11,85 12,85 14,35 17,35 21,42 25,42 28,42 33,5 38,5 kProduct grade B min. 6,11 7,21 8,51 11,15 12,15 13,65 16,65 20,58 24,58 27,58 32,5 37,5 A 4,35 5,12 6,03 7,9 8,6 9,65 kwaProduct gradeB min. 4,28 5,05 5,96 7,81 8,51 9,56 11,66 14,41 17,21 19,31 22,75 26,25 rmin
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1