1、Grooved pins, full-length parallel grooved, with pilot (IS0 8739 : 1997) English version of DIN EN IS0 8739 ICs 21.060.50 Descriptors: Fasteners, grooved pins. Zylinderkerbstifte mit Einfhrende (IS0 8739 : 1997) DIN EN IS0 8739 Supersedes DIN EN 28739, October 1992 edition. Previous editions DIN 147
2、0: 1961 -1 2, 1978-1 1 ; DIN 7978: 1956-08, 1963-06, 1977-02; DIN EN 28739: 1992-1 O. European Standard EN IS0 8739 : 1997 has the status of a DIN Standard. A comma is used as the decimal marker. National foreword This standard has been published in accordance with a decision taken by CEN/TC 185 to
3、adopt, without alteration, International Standard IS0 8739 as a European Standard. The responsible German body involved in its preparation was the Normenausschu Mechanische Verbindungselemente (Fasteners Standards Committee). The DIN 4000-9-1 tabular layout of article characteristics shall apply to
4、the pins covered in this standard. The DIN Standards corresponding to the International Standards referred to in clause 2 of the EN are as follows: IS0 Standard DIN Standard IS0 3269 DIN IS0 3269 IS0 4042 IS0 8749 DIN EN 28749 IS0 3506-1 DIN EN IS0 3506-1 DIN EN IS0 4042*) Amendments In comparison w
5、ith DIN EN 28739, October 1992 edition, the standard has been editorially revised and the scope extended to include specifications for stainless steel pins. National Annex NA Standards referred to (and not included in Normative references and Annex ZA) DIN 4000-9 DIN 50942 DIN EN 28749 DIN EN IS0 35
6、06-1 DIN EN IS0 4042 Tabular layout of article characteristics for bolts, pins, rivets, split pins and keys Phosphating metals - Principles and testing Pins and grooved pins - Shear test Corrosion-resistant stainless steel fasteners - Part 1 : Bolts, screws and studs Fasteners - Electroplated coatin
7、gs (ISO/DIS 4042 : 1996)*) *) At present at the stage of draft. EN comprises 6 pages. Q No pari of this standard may be reproduced without the prior permission of Ref. No. DIN EN IS0 8739 : 1998-03 DIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, D-10772 Berlin, has the exclusive
8、right of sale for German Standards (DIN-Normen). English price group 06 Sales No. 1106 08.98 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 8739 November 1997 ICs 21.060.50 Descriptors: Fasteners, grooved pins. Supersedes EN 28739 : 1992. English version Grooved pins, full-length parallel
9、grooved, with pilot (IS0 8739 : 1997) Goupilles canneles cannelures constantes sur toute la longueur dbouchantes, bout pilote (IS0 8739 : 1997) Zylinderkerbstifte mit Einfhrende (IS0 8739 : 1997) This European Standard was approved by CEN on 1997-1 0-1 7. CEN members are bound to comply with the CEN
10、KENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stand- ards may be obtained on application to the Central Secretariat or to
11、 any CEN member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
12、 CEN members are the national standards bodies of Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. CEN European Committee for Standardization Co
13、mit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels O 1997. CEN - All rights of exploitation in any form and by any means reserved worldwide for CEN national members. Ref. No. EN IS0 8739 : 1997 E Page 2 EN IS0 8739 : 1997 Foreword Int
14、ernational Standard IS0 8739 : 1997 which was prepared by ISO/TC 2 Fasteners of the International Organization for Standardization, has been adopted by Technical Committee CEN/TC 185 Threaded and non-threaded mechanical fasteners and acces- sories, the Secretariat of which is held by DIN, as a Europ
15、ean Standard. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, and conflicting national standards withdrawn, by May 1998 at the latest. In accordance with the CENKENELEC Internal Regulations, the national standards
16、 organizations of the follow- ing countries are bound to implement this European Standard: Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. Groo
17、ved pins, full-length parallel grooved, with pilot, Endorsement notice The text of the International Standard IS0 8739 : 1997 was approved by CEN as a European Standard without any modification. NOTE: Normative references to international publications are listed in Annex ZA (normative). Page 3 EN IS
18、0 8739 : 1997 1 Scope This International Standard specifies the characteristics of full-length parallel grooved pins, made of steel or austenitic stainless steel, with pilot which have three equally spaced grooves impressed longitudinally on their exterior surface and a pilot to facilitate insertion
19、, with nominal diameter, d, from 1,5 mm to 25 mm inclusive. The displaced material to each side of the grooves forming an expanded diameter d2 which is larger than the nominal diameter d, will cause a non-positive locking fit when these grooved pins are forced into a drilled hole equal to the nomina
20、l diameter d, (see clause 4). 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parti
21、es to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IS0 3269: 1988, Fasteners - Acceptance insp
22、ection. IS0 3506-1 :1997, Corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs. IS0 4042:-“, Fasteners - Electroplated coatings. IS0 8749:1986, Pins and grooved pins - Shear test. IS0 9717:1990, Phosphate conversion coatings for metals - Method of specifying requirements.
23、3 Dimensions See figure 1 and table 1. 1) Chamfer permissible. 2) The grooving angle 70“ applies only to grooved pins made from steel as shown in clause 5. The grooving angle may be modified depending on resilience of material. Figure 1 1) To be published. (Revision of IS0 4042:1989) Page 4 EN IS0 8
24、739 : 1997 1 nom. 1,5 2 2,5 3 tol. h9 45 6 8 10 12 16 20 25 hl 1 max.1 2 5 5 4 4 1.2 1,6 70,4 101,s Ainimum shear 1.6 5 7 7 4 6 6 2 2.5 3 181 283 444 trength, double” :N I 14 16 18 20 22 24 26 28 30 32 35 40 45 13.5 14,5 1.6 15,5 16.5 11.5 18.5 19,5 20.5 21,5 22,5 23,5 24,5 25,5 26,5 27,5 28,5 29,5
25、30.5 31,5 32.5 7 34,s 35.5 39,5 40,5 44.5 45.5 50 55 60 65 70 15 ao a5 90 95 100 7 2.84 4,4 49,5 50.5 54.25 55,75 59,25 60,75 64,25 65.75 69,25 70.75 74.25 75,75 79.25 80,75 84.25 85.75 89.25 90.75 94.25 95.75 99.25 100.75 +0,05 3 2.15 - 2.65 7 6,4 11.3 17,6 254 45,2 Expanded diameter, 4” ” 10,05 -
26、16,4 *O,l - 25,5 I) Applies only to grooved pins made from steel as shown in clause 5. !) The range of commercial lengths is between the stepped lines. I) The expanded diameter d, applies only to pins made from steel as shown in clause 5. For other materials, for example stainless steel, a reduction
27、 amount shall be subtracted from the given values and should be agreed between customer and supplier. L) For testing 4, a GO/NO GO ring gauge should be used. Page 5 EN IS0 8739 : 1997 Steel (St) Hardness 125 HV30 to 245 HV30 4 Application Austenitic stainless steel AI in accordance with IS0 3506-1,
28、hardness 210 HV30 to 280 HV30 The diameter of the hole into which the groove pin is to be inserted shall be equal to the nominal diameter d, of the mating pin and to tolerance class H11. 5 Requirements and reference International Standards See table 2. Table 2 - Requirements and reference Internatio
29、nal Standards Material? Grooves Surface finish Workmanship Shear strength test Accepta biiity Form of groove at the discretion of the supplier Plain, .e. pins to be supplied in natural finish treated with a protective lubricant, unless otherwise specified by agreement between customer and supplier.
30、Preferred coatings are black oxide, phosphate coating or zinc plating with chromate conver- sion coating (see IS0 9717 and IS0 4042). Other coatings as agreed between customer and supplier. All tolerances shall apply prior to the applica- tion of a plating or coating. Plain, .e. pins to be supplied
31、in natural finish. Pins shall free of irregularities or detrimental defects. The test shall be in accordance with IS0 8749. The acceptance procedure is covered in IS0 3269. 1) Other materials as agreed between customer and supplier. 6 Designation EXAMPLE 1 A full-length parallel grooved steel pin wi
32、th pilot with nominal diameter d, = 6 mm and nominal length 1 = 50 mm is designated as follows: Grooved pin IS0 8739 - 6 x 50 - St EXAMPLE 2 A full-length parallel grooved austenitic stainless steel pin of grade AI with pilot, with nominal diameter d, = 6 mm and nominal length i = 50 mm is designate
33、d as follows: Grooved pin IS0 8739 - 6 x 50 - Al Page 6 EN IS0 8739 : 1997 Annex ZA (normative) Normative references to international publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These no
34、rmative references cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. Publication Year Title - EN Year IS0 8749 1986 Pins and grooved pins - Shear test EN 28749 1992
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1