DIN EN ISO 9445-2-2010 Continuously cold-rolled stainless steel - Tolerances on dimensions and form - Part 2 Wide strip and plate sheet (ISO 9445-2 2009) German version EN ISO 9445.pdf

1、June 2010 Translation by DIN-Sprachendienst.English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 77

2、.140.20; 77.140.50!$i-_“1701060www.din.deDDIN EN ISO 9445-2Continuously cold-rolled stainless steel Tolerances on dimensions and form Part 2: Wide strip and plate/sheet (ISO 9445-2:2009)English translation of DIN EN ISO 9445-2:2010-06Kontinuierlich kaltgewalzter nichtrostender Stahl Grenzabmae und F

3、ormtoleranzen Teil 2: Kaltbreitband und Blech (ISO 9445-2:2009)Englische bersetzung von DIN EN ISO 9445-2:2010-06Acier inoxydable lamin froid en continu Tolrances sur les dimensions et la forme Partie 2: Larges bandes et tles (ISO 9445-2:2009)Traduction anglaise de DIN EN ISO 9445-2:2010-06supersede

4、sDIN EN ISO 9445:2006-05www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.DIN EN ISO 9445-1:2010-06,Together with Document comprises 14 pages06.10 DIN EN ISO 9445-2:2010-06 2 A comma is used as the decimal marker. National foreword This standard has been pr

5、epared by Technical Committee ISO/TC 17 “Steel” in collaboration with Technical Committee ECISS/TC 105 “Steels for heat treatment, alloy steels, free-cutting steels and stainless steels” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Eise

6、n und Stahl (Steel and Iron Standards Committee), Working Committee 20/2 Manormen fr kaltgewalzte Flacherzeugnisse. Amendments This standard differs from DIN EN ISO 9445:2006-05 as follows: a) The standard has been divided into two parts, DIN EN ISO 9445-1 and DIN EN ISO 9445-2. b) The standard has

7、been editorially revised. Previous editions DIN 59381: 1975-08, 1980-08 DIN 59382: 1975-08 DIN EN 10258: 1997-07 DIN EN 10259: 1997-07 DIN EN ISO 9445: 2006-05 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 9445-2 March 2010 ICS 77.140.20; 77.140.50 Supersedes EN ISO 9445:2006English Versi

8、on Continuously cold-rolled stainless steel - Tolerances on dimensions and form - Part 2: Wide strip and plate/sheet (ISO 9445-2:2009) Acier inoxydable lamin froid en continu - Tolrances sur les dimensions et la forme - Partie 2: Larges bandes et tles (ISO 9445-2:2009) Kontinuierlich kaltgewalzter n

9、ichtrostender Stahl - Grenzabmae und Formtoleranzen - Teil 2: Kaltbreitband und Blech (ISO 9445-2:2009) This European Standard was approved by CEN on 7 February 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Sta

10、ndard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, Fren

11、ch, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia

12、, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZAT

13、ION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 9445-2:2010: EContents DIN EN ISO 9445-2:2010-06 EN ISO

14、 9445-2:2010 (E) 2 PageForeword .3 1 Scope4 2 Normative references4 3 Terms and definitions .4 4 Information to be supplied by the purchaser .4 5 Type of delivery and delivery condition5 6 Preferred thicknesses.6 7 Tolerances on thickness for cold-rolled wide strip and products obtained from cold-ro

15、lled wide strip6 8 Tolerances on width for cold-rolled wide strip and products obtained from cold-rolled wide strip7 9 Preferred coil inner diameters for cold-rolled wide strip and slit cold-rolled wide strip.8 10 Tolerances on length for plate/sheet cut from cold-rolled wide strip and for cut lengt

16、hs obtained from slit cold-rolled wide strip.8 11 Tolerances on edge camber for cold-rolled wide strip and products obtained from cold-rolled wide strip.9 12 Tolerances on squareness for plate/sheet obtained from cold-rolled wide strip and cut lengths obtained from slit cold-rolled wide strip .9 13

17、Tolerances on flatness for plate/sheet obtained from cold-rolled wide strip and cut lengths obtained from slit cold-rolled wide strip .9 14 Edge waviness tolerances for cold-rolled strip .10 15 Form of coils 10 16 Ordered format for plate/sheet and cut lengths.10 17 Measurement of thickness for cold

18、-rolled wide strip, plate/sheet cut from cold-rolled wide strip, slit cold-rolled wide strip and cut lengths obtained from slit cold-rolled wide strip10 18 Measurement of width.11 19 Measurement of length .11 20 Measurement of edge camber11 21 Measurement of squareness12 22 Measurement of flatness a

19、nd waviness12 Foreword The text of ISO 9445-2:2009 has been prepared by Technical Committee ISO/TC 17 “Steel” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 9445-2:2010 by Technical Committee ECISS/TC 105 “Steels for heat treatment, alloy steels, free-c

20、utting steels and stainless steels” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2010, and conflicting national standards shall be withdrawn a

21、t the latest by September 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 9445:2006. According t

22、o the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, La

23、tvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 9445-2:2009 has been approved by CEN as a EN ISO 9445-2:2010 without any modification. DIN EN ISO 9445-2:2010-

24、06 EN ISO 9445-2:2010 (E) 3 1 Scope This part of ISO 9445 specifies the tolerances on dimensions and form for continuously cold-rolled stainless steel wide strip and plate/sheet, in thicknesses from 0,30 mm to 8,0 mm and in rolling widths from 600 mm to 2 100 mm. It also applies to slit cold-rolled

25、wide strip in widths less than 600 mm manufactured from wide strip by longitudinal slitting and to cut lengths manufactured from such strip. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited

26、applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6929, Steel products Definitions and classification 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 6929 apply. 4 Information to be

27、 supplied by the purchaser 4.1 It shall be the responsibility of the purchaser to specify all requirements that are necessary for products under this specification. Such requirements to be considered include, in the order listed, but are not limited to, the following: a) the type of delivery see 5.2

28、 a) to 5.2 d); b) the number of this International Standard, i.e. ISO 9445-2; c) the thickness in millimetres (if necessary accurate to two decimal places) and, if required, including the relevant code letter (S) for a special tolerance; d) the measurement of the thickness method to be used, either

29、method A in accordance with 17.2 and tolerances according to Table 1 with the relevant code letter (A) or method B in accordance with 17.3 and tolerances according to Table 2 with the relevant code letter (B); e) the width in millimetres and, if required, including the relevant code letter (S) for a

30、 special tolerance; DIN EN ISO 9445-2:2010-06 EN ISO 9445-2:2010 (E) 4 f) for cold-rolled wide strip and plate/sheet, whether mill (M) or trimmed (T) edges are required. The other products will normally have trimmed edges (see 5.3); g) for plate/sheet and cut lengths, the length in millimetres and,

31、if a special tolerance is required, the code letter S; h) for cold-rolled plate/sheet and cut lengths, the code letter FS where a special tolerance is required for flatness. EXAMPLE 1 Cut length obtained from slit cold-rolled wide strip according to this part of ISO 9445 with a specified thickness o

32、f 1,5 mm, special thickness tolerance (S), measuring method A, with a specified width of 200 mm, special tolerance on width (S), with a specified length of 500 mm, special tolerance on length (S) and a special tolerance on flatness (FS). Cut length from slit cold-rolled wide strip ISO 9445-2 1,5SA x

33、 200S x 500S-FS EXAMPLE 2 Cold-rolled wide strip according to this part of ISO 9445 with a specified thickness of 0,8 mm, normal tolerance, measuring method B, width 1 250 mm, with trimmed edges (T). Cold-rolled wide strip ISO 9445-2 0,80B x 1250T 4.2 In the absence of information in the order conce

34、rning special requirements for tolerances on dimension and shape see 4.1 c), e), g) and h), flat products covered by this part of ISO 9445 will be delivered according to the basic specifications of this part of ISO 9445, i.e. with normal tolerances. 5 Type of delivery and delivery condition 5.1 Gene

35、ral In the absence of agreements at the time of enquiry and order concerning special requirements for the delivery conditions given in 5.3, flat products covered by this part of ISO 9445 will be delivered according to the basic specifications of this part of ISO 9445. 5.2 Type of delivery Flat produ

36、cts according to this part of ISO 9445 can be supplied as a) cold-rolled wide strip (strip in rolled widths equal to or greater than 600 mm); b) cold-rolled plate/sheet cut from cold-rolled wide strip according to item 5.2 a); c) slit cold-rolled wide strip manufactured by longitudinal slitting of w

37、ide strip according to item 5.2 a); d) cut lengths from slit cold-rolled wide strip cut from slit cold-rolled wide strip according to item 5.2 c). 5.3 Delivery condition of cold-rolled wide strip and products obtained from cold-rolled wide strip Cold-rolled wide strip and plate/sheet cut from cold-r

38、olled wide strip are supplied with either mill (M) or trimmed (T) edges. Slit cold-rolled wide strip and cut lengths obtained from slit cold-rolled wide strip normally have trimmed edges. DIN EN ISO 9445-2:2010-06 EN ISO 9445-2:2010 (E) 5 6 Preferred thicknesses For cold-rolled wide strip and the pr

39、oducts obtained from cold-rolled wide strip see 5.2 a), 5.2 b), 5.2 c) and 5.2 d), the following preferred thicknesses exist: 0,30 mm; 0,40 mm; 0,50 mm; 0,60 mm; 0,70 mm; 0,80 mm; 1,00 mm; 1,20 mm; 1,50 mm; 2,00 mm; 2,50 mm; 3,00 mm; 4,00 mm; 5,00 mm; 6,00 mm; 8,00 mm. 7 Tolerances on thickness for

40、cold-rolled wide strip and products obtained from cold-rolled wide strip The tolerances on thickness can be taken from Table 1 (see 17.2 method A) or Table 2 (see 17.3 method B). NOTE The two tables are necessary to recognize different “custom and practice” in different countries with respect to mea

41、surement methods. Table 1 Tolerances on specified thickness for cold-rolled wide strip, plate/sheet cut from cold-rolled wide strip, slit cold-rolled wide strip and cut lengths obtained from slit cold-rolled wide strip Dimensions in millimetres Normal tolerances for a rolled width of Special toleran

42、ces (S) for a rolled width of Specified thickness t w u 2 100 w u 1 000 1 000 6 000 15 13 Tolerances on flatness for plate/sheet obtained from cold-rolled wide strip and cut lengths obtained from slit cold-rolled wide strip The flatness tolerances for plate/sheet obtained from cold-rolled wide strip

43、 and cut lengths obtained from slit cold-rolled wide strip shall not exceed 10 mm for normal cases and 7 mm where a special tolerance (FS) is required for lengths u 3 000 mm and 12 mm for normal cases and 8 mm where a special tolerance (FS) is required for lengths 3 000 mm. This requirement does not

44、 apply to material supplied in the work-hardened condition and in the condition 2D (cold-rolled, heat-treated, pickled). DIN EN ISO 9445-2:2010-06 EN ISO 9445-2:2010 (E) 9 14 Edge waviness tolerances for cold-rolled strip For cold-rolled wide strip or slit cold-rolled wide strip, the waviness of the

45、 edges, i.e. the ratio of wave height (h) to wave length (l) shall be maximum 0,03 for all thicknesses (see Figure 1). This requirement does not apply to material supplied in the work-hardened condition and in the condition 2D (cold-rolled, heat-treated, pickled). Key h/l = waviness Figure 1 Edge wa

46、viness tolerances for cold-rolled strip 15 Form of coils The coils delivered according to this part of ISO 9445 shall be tightly wound, as round as possible and with straight edges. Gradual displacement of the edge of the strip to one side shall not exceed 35 mm in case of trimmed (slit) edges and 7

47、0 mm in case of mill (as rolled) edges. 16 Ordered format for plate/sheet and cut lengths When ordering, an agreement may be made that the ordered format be contained in every piece supplied. In this case, the tolerances on width, length, edge camber and out-of-squareness shall be agreed at the time

48、 of enquiry and order. 17 Measurement of thickness for cold-rolled wide strip, plate/sheet cut from cold-rolled wide strip, slit cold-rolled wide strip and cut lengths obtained from slit cold-rolled wide strip 17.1 The two methods given below in 17.2 (method A) and 17.3 (method B) are alternatives, for use with Tables 1 and 2 respectively. 17.2 Method A: The thickness is measured at any point located more than 20 mm from the edges in the case of slit edges and at any point located more than 30 mm from the edges in t