DIN EN ISO 9974-1-2000 Connections for general use and fluid power - Ports and studs ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 1 Threaded ports (I.pdf

1、DEUTSCHE NORM SeDtember 2000 Connections for general use and fluid power Ports and stud ends with IS0 261 threads with elastomeric Part 1: Threaded ports (IS0 9974-1 : 1996) English version of DIN EN IS0 9974-1 or metal-to-metal sealing DIN - EN IS0 9974-1 ICs 23.100.60 Supersedes parts of Leitungsa

2、nschlsse fr Fluidtechnik und allgemeine Anwendung - Einschraublcher und Einschraubzapfen mit Gewinde nach IS0 261 und Elastomerdichtung oder metallener Dichtkante - Teil 1 : Einschraublcher (IS0 9974-1 : 1996) DIN 3852-1, February 1992 edition. European Standard EN IS0 9974-1 : 2000 has the status o

3、f a DIN Standard. A comma is used as the decimal marker. National foreword This standard has been published in accordance with a decision taken by ECISS/TC 29 to adopt, without alteration, International Standard IS0 9974-1 as a European Standard. The responsible German body involved in its preparati

4、on was the Normenausschuss Rohrverschraubungen (Pipe Joints Standards Committee). The DIN Standards corresponding to the International Standards referred to in clause 2 of the EN are as follows: IS0 261 Supplement to DIN 13-12 IS0 9974-2 IS0 9974-3 DIN EN IS0 9974-2 DIN EN IS0 9974-3 Amendments Part

5、s of DIN 3852-1, February 1992 edition, have been superseded by the specifications of EN IS0 9974-1, which is identical to IS0 9974-1. Previous editions DIN 3852-1 : 1953-08, 1964-1 O, 1966-05, 1978-09, 1992-02. National Annex NA Standards referred to (and not included in Normative references and An

6、nex A) Supplement to DIN 13-1 2 IS0 metric screw threads - Coarse and fine pitch threads with diameters from 1 mm to 300 mm - General plan of the screw threads according to IS0 261 : 1973 Connections for general use and fluid power - Ports and stud ends with IS0 261 threads with elastomeric or metal

7、-to-metal sealing - Part 2: Stud ends with elastomeric sealing (type E) (IS0 9974-2 : 1996) Connections for general use and fluid power - Ports and stud ends with IS0 261 threads with elastomeric or metal-to-metal sealing - Part 3: Stud ends with metal-to-metal sealing (type B) (IS0 9974-3 : 1996) D

8、IN EN IS0 9974-2 DIN EN IS0 9974-3 EN comprises 6 pages. No pari of this standard may be reproduced without the prior permission of Ref. No. DIN EN IS0 9974-1 : 2000-0 Y Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, s the exclusive right of sale for German St

9、andards (DIN-Normen). English price group O7 Sales No. 1107 03.01 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 9974-1 May 2000 ICs 23.1 00.60 English version Connections for general use and fluid power Ports and stud ends with IS0 261 threads with elastomeric or metal-to-metal sealing Pa

10、rt 1 : Threaded ports (IS0 9974-1 : 1996) Raccordements pour applications gnrales et transmissions hydrauli- ques et pneumatiques - Orifices et lments mles filetage IS0 261 et joint en lastomre ou tanchit mtal sur mtal - Partie 1 : Orifices Leitungsanschlsse fr Fluidtechnik und allgemeine Anwendung

11、- Ein- schraublcher und Einschraubzapfen mit Gewinde nach IS0 261 und Elastomerdichtung oder metallener Dichtkante - Teil 1 : Einschraublcher filets (IS0 9974-1 : 1996) (IS0 9974-1 : 1996) This European Standard was approved by CEN on 2000-04-08. CEN members are bound to comply with the CENKENELEC I

12、nternal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stand- ards may be obtained on application to the Central Secretariat or to any CEN

13、member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN memb

14、ers are the national standards bodies of Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. CEN European Committee for Standardization Comit Europ

15、en de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels O 2000. CEN - All rights of exploitation in any form and by any means reserved worldwide for CEN national members. Ref. No. EN IS0 9974-1 : 2000 E Page 2 EN IS0 9974-1 : 2000 Foreword Internat

16、ional Standard IS0 9974-1 : 1996 Connections for general use and fluid power - Ports and stud ends with IS0 261 threads with elastomeric or metal-to-metal sealing - Part 1 : Threaded ports, which was prepared by ISO/TC 5 Ferrous metal pipes and metallic fittings of the International Organization for

17、 Standardization, has been adopted by Technical Committee ECISS/TC 29 Steel tubes and fittings for steel tubes, the Secretariat of which is held by UNI, as a European Standard. This European Standard shall be given the status of a national standard, either by publication of an identical text or by e

18、ndorsement, and conflicting national standards withdrawn, by November 2000 at the latest. In accordance with the CENKENELEC Internal Regulations, the national standards organizations of the follow- ing countries are bound to implement this European Standard: Austria, Belgium, the Czech Republic, Den

19、mark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. Endorsement notice The text of the International Standard IS0 9974-1 : 1996 was approved by CEN as a European Standard without any modif

20、ication. Introduction In fluid power systems, power is transmitted and controlled through a fluid (liquid or gas) under pressure within an enclosed circuit. In general appli- cations, a fluid may be conveyed under pressure. Components are connected through their threaded ports by fluid conduc- tor f

21、ittings to tubes and pipes or to hose fittings and hoses. Ports are an integral part of fluid power components, such as pumps, motors, valves, cylinders, etc. Page 3 EN IS0 9974-1 : 2000 1 Scope This part of IS0 9974 specifies dimensions for ports with IS0 261 threads and elastomeric (type E) or met

22、al-to- metal type BI sealing for general use and in fluid power applications with the stud ends detailed in IS0 9974-2 and IS0 9974-3. It also specifies test methods and the designation of these ports Ports in accordance with this part of IS0 9974 may be used at working pressures up to 63 MPa (630 b

23、ar l). The permissible working pressure depends upon the port size, materials, design, working conditions, ap- plication, etc. For threaded ports and stud ends specified in new designs in hydraulic fluid power applications, only IS0 6149 is to be used. Threaded ports and stud ends in accordance with

24、 IS0 1179, IS0 9974 and IS0 11926 are not to be used for new designs in hydraulic fluid power applications. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of IS0 9974. At the time of publication, the edition

25、s indicated were valid. All standards are subject to revision, and parties to agreements based on this part of IS0 9974 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid In

26、ternational Stan- dards. IS0 261 :- 2), IS0 general-purpose metric screw threads - General pian. IS0 5598: 1985, Fluid power systems and components - Vocabulary. IS0 9974-2: 1996, Connections for general use and fluid power - Ports and stud ends with IS0 267 threads with elastomeric or metal-to-meta

27、l sealing - Part 2: Stud ends with elastomeric sealing type El. IS0 9974-3: 1996, Connections for general use and fluid power - Ports and stud ends with IS0267 threads with elastomeric or metal-to-metal sealing - Part 3: Stud ends with metal-to-metal sealing type B1. 3 Definitions For the purposes o

28、f this part of IS0 9974, the defi- nitions given in IS0 5598 apply. 4 Dimensions Ports shall conform to the dimensions shown in figure 1 and given in table 1, 1) 1 bar = 0,l MPa = 105 Pa; 1 MPa = 1 N/mm2 2) To be published. (Revision of IS0 261 :1973) Page 4 EN IS0 9974-1 : 2000 Surface roughness in

29、 micrornetres This dimension only appties when tap drill cannot pass through entire boss Figure 1 - Port Table 1 - Fort dimensions Dimensions in millimetres M8x1 MlOxI M12x1,5 M14x1,5 M16x 1,5 M18x1,5 M20 x 1,5 3) M22 x 1.5 M26 x 1.5 M27 x 24) M33 x 2 M42 x 2 M48 x 2 d2 ref. 3 4,5 6 7 9 11 10 14 l.

30、8 16 23 30 36 nom. d3 to1 8 10 12 14 16 18 20 22 26 27 33 42 48 + 0.2 O + 0.3 O d4 min. 13 15 18 20 23 25 27 28 33 33 41 51 56 L1 rnax. 12 min. 8 8 12 12 12 12 14 14 16 16 18 20 22 L3 2 min. 10 10 15 15 15 15 17 17 19 20 22 24 36 W 0,1 1) Conforming to IS0 261 2) The tap drill depths given require t

31、he use of a bottoming tap to produce the specified full thread lengths. Where standard taps are used the tap drill depths shall be increased accordingly. 3) For measurement applications. 4) M27 x 2 is used only in S (heavy-duty) series. Page 5 EN IS0 9974-1 : 2000 5 Test methods Ports shall be teste

32、d together with stud ends in accor- dance with the test methods and requirements given in IS0 9974-2 and IS0 9974-3. 6 Designation of ports The ports shall be designated by a) “Port“; b) c) reference to this part of IS0 9974, .e. IS0 9974-1 ; thread size (d, x P). EXAMPLE Port IS0 9974-1 - M10 x 1 7

33、 Identification statement (Reference to this part of IS0 9974) Use the following statement in test reports, cata- logues and sales literature when electing to comply with this part of IS0 9974 “Threaded ports conform to IS0 9974-1 1996, Con- nections for general use and fluid power - Ports and stud

34、ends with IS0 267 threads with elastomeric or metal-to-metai sealing - Part 1 Threaded ports “ Page 6 EN IS0 9974-1 : 2000 Annex A (informative) Bibliography I1 I I21 I31 I41 i51 I61 I71 i81 IS0 1 1 O1 : 1983, Technical drawings - Geometri- cal tolerancing - Tolerances of form, orientation, location

35、 and run-out - Generalities, definitions, symbols, indications on drawings IS0 1 179-1 :-SI, Connections for general use and fluid power - Ports and crud ends with IS0 228-1 threads with elastomeric or metal-to-metal seal- ing - Part 1: Threaded ports. IS0 1 179-2:- 31, Connections for general use a

36、nd fluid power - Ports and stud ends with IS0 228-1 threads with elastomeric or metal-to-metal seal- ing - Part 2: Heavy-duty (S series) and light-duty (L seriesl stud ends with elastomeric sealing (type El. IS0 1 179-3:- 3, Connections for general use and fluid power - Ports and stud ends with IS0

37、2287 threads with elastomeric or metal-to-metal seal- ing - Part 3: Light-duty (1 series) stud ends with sealing by O-ring with retaining ring (types G and HI. IS0 1 179-4:- 31, Connections for general use and fluid power - Ports and stud ends with IS0 2287 threads with elastomeric or metal-to-metal

38、 seal- ing - Part 4: Stud ends for general use only with metal-to-metal sealing (type B). IS0 1302: 1992, Technical drawings - Method of indicating surface texture. IS0 6149-1 :1993. Connections for fluid power and general use - Ports and stud ends with IS0 261 threads and O-ring sealing - Part 1: P

39、orts with O-ring seal in truncated housing. IS0 6149-2:1993, Connections for fluid power and general use - Ports and stud ends with IS0 261 threads and O-ring sealing - Part 2: Heavy-duty (S series) stud ends - Dimensions, design, lest methods and requirements. I91 IS0 6149-3:1993, Connections for f

40、luld power and general use - Ports and stud ends with IS0 261 threads and O-ring sealing - Part 3: Light-duty IL series) stud ends - Dimensions, design, test methods and requirements. 1101 IS0 6410-1 :1993, Technical drawings - Screw threads and threaded parts - Part 7: General conventions. i1 1 I I

41、S0 8434-1 1994, Metallic tube connections for fluid power and general use - Part 1: 24 degree compression fittings. il 21 IS0 8434-4:1995, Metallic tube connections for fluid power and general use - Part 4: 24 degree cone connectors with O-ring weid-on nipples. I 31 IS0 1 1926-1 :I 995, Connections

42、for general use and fluid power - Ports and stud ends with IS0 725 threads and O-ring sealing - Par? I: Ports with O-ring seal in truncated housing. I141 IS0 1 1926-2:1995, Connections for general use and fluid power - Ports and stud ends with IS0 725 threads and O-ring sealing - Part 2. Heavy-duty

43、(S series) stud ends. 1 51 IS0 1 1 926-3: 1 995, Conneclions for general use and fluid power - Ports and stud ends with IS0 725 threads and O-ring seaiing - Part 3. Light-duty IL series) stud ends. 161 DIN 3852-1 :I 992, Stud ends and tapped holes, with metric fine pitch thread, for use with com- pression couplings, valves and screw plugs - Dimensions. 3) To be published