DIN EN ISO 20848-3-2008 Packaging - Plastics drums - Part 3 Plug bung closure systems for plastics drums with a nominal capacity of 113 6 l to 220 l (ISO 20848-3 2006) German versi.pdf

1、September 2008DEUTSCHE NORM English price group 14No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 55.140!$QfA“1466730w

2、ww.din.deDDIN EN ISO 20848-3Packaging Plastics drums Part 3: Plug/bung closure systems for plastics drums with a nominalcapacity of 113,6 l to 220 l (ISO 20848-3:2006)English version of DIN EN ISO 20848-3:2008-09Verpackung Kunststofffsser Teil 3: Verschlusssysteme fr Kunststoff-Spundfsser mit einem

3、Nennvolumen von113,6 l bis 220 l (ISO 20848-3:2006)Englische Fassung DIN EN ISO 20848-3:2008-09SupersedesDIN EN 12708:2000-03www.beuth.deDocument comprises 29 pagesDIN EN ISO 20848-3:2008-09 2 National foreword This standard has been prepared by Technical Committee ISO/TC 122 “Packaging” with TSE (T

4、urkey) holding the secretariat. The secretariat is currently held by JISC (Japan) and ISIRI (Iran). This standard has been published in accordance with a decision taken by Technical Committee CEN/TC 261 “Packaging” (Secretariat: AFNOR, France), Subcommittee SC 5 “Primary packaging and transport pack

5、aging” (Secretariat: BSI, United Kingdom) to adopt, without alteration, International Standard ISO 20848-3:2006 as European Standard EN ISO 20848-3:2008. The responsible German body involved in its preparation was the Normenausschuss Verpackungswesen (Packaging Standards Committee), Technical Commit

6、tee NA 115-02-03 AA Spund- und Deckelfsser. DIN EN ISO 20848 consists of the following parts, under the general title Packaging Plastics drums: Part 1: Removable head (open head) drums with a nominal capacity of 113,6 l to 220 l Part 2: Non-removable head (tight head) drums with a nominal capacity o

7、f 208,2 l and 220 l Part 3: Plug/bung closure systems for plastics drums with a nominal capacity of 113,6 l to 220 l The DIN Standard corresponding to the International Standard referred to in this document are as follows: ISO 228-1 DIN EN ISO 228-1 ISO 16104 DIN EN ISO 16104 Amendments This standar

8、d differs from DIN EN 12708:2000-03 as follows: a) The specifications have been taken from DIN EN 12708. b) The standard has been editorially revised. Previous editions DIN 6131-3: 1985-07, 1989-08 DIN EN 12708: 2000-03 National Annex NA (informative) Bibliography DIN EN ISO 228-1, Pipe threads wher

9、e pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation DIN EN ISO 16104, Packaging Transport packaging for dangerous goods Tests methods EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 20848-3 June 2008 ICS 55.140 English Version Packaging - Plast

10、ics drums - Part 3: Plug/bung closure systems for plastics drums with a nominal capacity of 113,6 l to 220 l (ISO 20848-3:2006) Emballages - Fts en matire plastique - Partie 3: Systmes de fermeture bondes pour fts en matire plastique dune capacit nominale de 113,6 l 220 l (ISO 20848-3:2006) Verpacku

11、ng - Kunststofffsser - Teil 3: Verschlusssysteme fr Kunststoff-Spundfsser mit einem Nennvolumen von 113,6 l bis 220 l (ISO 20848-3:2006) This European Standard was approved by CEN on 16 May 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions

12、 for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three off

13、icial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austri

14、a, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITT

15、EE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 20848-3:2008: E2 DIN EN ISO 20848-

16、3:2008-09 EN ISO 20848-3:2008 (E) Contents Page Foreword3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Requirements.6 4.1 Dimensions.6 4.2 Gaskets .6 4.3 Closure torque .6 4.4 Material identification symbol 6 4.5 Materials .7 4.6 Thread .7 4.7 Plug/bung .7 4.8 Vent

17、ed plug/bung.7 4.9 Finish 7 Annex A (normative) Plug/bung closure system BCS 70 6 .8 Annex B (normative) Plug/bung closure system BCS 56 4 10 Annex C (normative) Plug/bung closure system BCS 38 6 15 Annex D (normative) Plug/bung closure system BCS 24 4 17 Annex E (normative) Plug/bung closure system

18、 BCS G2 5 19 Annex F (normative) Plug/bung closure system BCS G2 11,5. 21 Annex G (normative) Plug/bung closure system BCS G3/4 14 23 Annex H (normative) International material code symbols . 25 Bibliography. 27 Foreword 3 EN ISO 20848-3:2008 (E) DIN EN ISO 20848-3:2008-09 The text of ISO 20848-3:20

19、06 has been prepared by Technical Committee ISO/TC 122 “Packaging” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 20848-3:2008 by Technical Committee CEN/TC 261 “Packaging” the secretariat of which is held by AFNOR. This European Standard shall be given

20、 the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2008, and conflicting national standards shall be withdrawn at the latest by December 2008. Attention is drawn to the possibility that some of the elements of this document may

21、 be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria,

22、 Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement n

23、otice The text of ISO 20848-3:2006 has been approved by CEN as a EN ISO 20848-3:2008 without any modification. Introduction Throughout the world, a large number of plastics drum types with different dimensions and characteristics are being used. The differences in types of closures may result in dif

24、ferences in filling and handling. ISO 20848 specifies the characteristics and dimensions of closures for plastics drums which are of importance for the worldwide safe handling and transport of substances and for the continued reuse of the drums during their life cycle. Detailed performance requireme

25、nts and the related test methods are not included as they depend upon the specific application. Where the drums are intended to be used for the transport of dangerous goods, attention is drawn to the regulatory requirements which govern the transport of those goods in the countries concerned, includ

26、ing capseals/overseals fitted in accordance with the certificate. Depending upon the mode of transport, this means meeting the requirements of: UN (United Nations) Recommendations on the Transport of Dangerous Goods, ICAO (International Civil Aviation Organization) Technical Instructions for the Saf

27、e Transport of Dangerous Goods by Air, IMO (International Maritime Organization) International Maritime Dangerous Goods (IMDG) Code. This involves the certification and marking of the drums according to the regulations. 4 DIN EN ISO 20848-3:2008-09 EN ISO 20848-3:2008 (E) 1 Scope This part of ISO 20

28、848 specifies the characteristics and dimensions of plug/bung closure systems for internally threaded openings in plastics drums of nominal capacity 113,6 l to 220 l. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated reference

29、s, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation 3 Terms and definitions For the

30、purposes of this document, the following terms and definitions apply. 3.1 plug/bung closure system BCS system of one or more components which enables an internally threaded container to be filled or emptied and then secured to provide a leakproof seal for subsequent transport or storage NOTE See Fig

31、ures A.1 to G.2. 3.2 plug/bung device, provided with an external thread, which closes an opening in a drum 3.3 plug/bung housing neck that part of the container designed to receive the plug/bung 3.4 gasket washer component which, under compression, facilitates a leakproof seal between the plug/bung

32、and plug/bung housing 5 EN ISO 20848-3:2008 (E) DIN EN ISO 20848-3:2008-09 3.5 gasket sealing faces those areas of the plug/bung or plug/bung housing designed to be in contact with the gasket and make the seal 3.6 capseal/overseal cap or fitting attached to the plug/bung housing which incorporates a

33、 facility for providing tamper evidence and provides protection against the ingress of foreign matter into the closure 4 Requirements 4.1 Dimensions The dimensions and tolerances of the closure systems shall conform to the appropriate annexes of this part of ISO 20848 as given in Table 1. Measuremen

34、ts shall be conducted at ambient conditions but shall not be made within 48 h of manufacture. For plug/bung housings, diameter measurements shall be the mean of at least two readings orientated at 90 to each other. Table 1 Annexes of this part of ISO 20848 specifying dimensions and tolerances for di

35、fferent plug/bung closure system (BCS) types BCS type Applicable annex BCS 70 6 A BCS 56 4 B BCS 38 6 C BCS 24 4 D BCS G2 5 E BCS G2 11,5 F BCS G3/4 14 G 4.2 Gaskets Gaskets shall be positioned correctly on the plug/bung. 4.3 Closure torque A recommended closure torque, including tolerance, shall be

36、 specified. In addition, the appropriate tooling for closing shall be specified. 4.4 Material identification symbol All the plastics components of the closure systems, excluding gaskets, shall be permanently marked with the relevant material identification symbol, i.e. the symbol identifying the mat

37、erial from which the component is made as shown in Annex H. 6 DIN EN ISO 20848-3:2008-09 EN ISO 20848-3:2008 (E) 4.5 Materials The plug/bung and gasket, where used, shall be manufactured from materials appropriate to the physical and chemical requirements of their intended use. 4.6 Thread The thread

38、 shall be as specified in Figures A.1 to G.2. 4.7 Plug/bung The plug/bung shall be designed so that it can be inserted or removed by means of a simple tool. 4.8 Vented plug/bung For ease of identification when fitted in drums, a vented plug/bung and capseal/overseal shall be coloured yellow. A vente

39、d plug/bung used for drums intended to contain dangerous goods should be in accordance with the applicable regulations. A plastic plug should be fitted with a capseal/overseal of such a design as to ensure venting is not impeded. 4.9 Finish The nature of the internal and external finish of the plug/

40、bung and gasket shall be appropriate to the physical and chemical requirements of their intended use. NOTE The nature of the internal and external finish should be agreed between the purchaser and the supplier. 7 EN ISO 20848-3:2008 (E) DIN EN ISO 20848-3:2008-09 Annex A (normative) Plug/bung closur

41、e system BCS 70 6 A.1 Nomenclature for closure system Dimensions in millimetres Key 1 plastics capseal 2 metal/plastics capseal 3 gasket 4 plug/bung housing 5 plug/bung 6 gasket sealing faces aMinimum clearance for crimping tool. Figure A.1 Plug/bung closure system BCS 70 6 general view 8 DIN EN ISO

42、 20848-3:2008-09 EN ISO 20848-3:2008 (E) A.2 Dimensions for closure system Dimensions in millimetres aPitch. Figure A.2 Plug/bung closure system BCS 70 6 plastics capseal 9 EN ISO 20848-3:2008 (E) DIN EN ISO 20848-3:2008-09 Annex B (normative) Plug/bung closure system BCS 56 4 B.1 Nomenclature for c

43、losure system Dimensions in millimetres Key 1 metal capseal 2 plastics capseal 3 gasket 4 plug/bung housing 5 plug/bung 6 gasket sealing faces aMinimum clearance for crimping tool. Figure B.1 Plug/bung closure system BCS 56 4 general view 10 DIN EN ISO 20848-3:2008-09 EN ISO 20848-3:2008 (E) B.2 Dim

44、ensions for closure system Dimensions in millimetres Key 1 metal/plastics capseal 2 metal capseal X proposal for sealing geometry aPitch. Figure B.2 Plug/bung closure system BCS 56 4 metal capseal and metal/plastics capseal 11 EN ISO 20848-3:2008 (E) DIN EN ISO 20848-3:2008-09 Dimensions in millimet

45、res Key 1 plastics capseal Y proposal for sealing geometry aPitch. Figure B.3 Plug/bung closure system BCS 56 4 plastics capseals 12 DIN EN ISO 20848-3:2008-09 EN ISO 20848-3:2008 (E) Dimensions in millimetres Key 1 plug/bung type 4 NU aPitch. Figure B.4 Plug/bung closure system BCS 56 4 plug/bung t

46、ype 4 NU 13 EN ISO 20848-3:2008 (E) DIN EN ISO 20848-3:2008-09 Dimensions in millimetres Key 1 plug/bung type 4N with G3/4 through hole 2 plug/bung type 6N Figure B.5 Plug/bung closure system BCS 56 4 plug/bung type 4N with G3/4 threaded recess and plug/bung type 6N 14 DIN EN ISO 20848-3:2008-09 EN

47、ISO 20848-3:2008 (E) Annex C (normative) Plug/bung closure system BCS 38 6 C.1 Nomenclature for closure system Dimensions in millimetres Key 1 plastics capseal 2 gasket 3 plug/bung housing 4 plug/bung 5 gasket sealing faces aMinimum clearance for crimping tool. Figure C.1 Plug/bung closure system BC

48、S 38 6 general view 15 EN ISO 20848-3:2008 (E) DIN EN ISO 20848-3:2008-09 C.2 Dimensions for closure system Dimensions in millimetres aPitch. Figure C.2 Plug/bung closure system BCS 38 6 plastics capseal 16 DIN EN ISO 20848-3:2008-09 EN ISO 20848-3:2008 (E) Annex D (normative) Plug/bung closure syst

49、em BCS 24 4 D.1 Nomenclature for closure system Dimensions in millimetres Key 1 metal capseal 2 metal/plastics capseal 3 gasket 4 plug/bung housing 5 plug/bung 6 gasket sealing faces aMinimum clearance for crimping tool. Figure D.1 Plug/bung closure system BCS 24 4 general view 17 EN ISO 20848-3:2008 (E) DIN EN ISO 20848-3:2008-09 D.2 Dimensions for closure system Dimensions in millimetresKey 1 metal capseal 2 metal/plastics capseal