DIN EN ISO 21003-5-2008 Multilayer piping systems for hot and cold water installations inside buildings - Part 5 Fitness for purpose of the system (ISO 21003-5 2008) English versio.pdf

1、November 2008DEUTSCHE NORM English price group 11No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91.140.60!$Rx-“147851

2、0www.din.deDDIN EN ISO 21003-5Multilayer piping systems for hot and cold water installations insidebuildings Part 5: Fitness for purpose of the system (ISO 21003-5:2008)English version of DIN EN ISO 21003-5:2008-11Mehrschichtverbund-Rohrleitungssysteme fr die Warm- und Kaltwasserinstallationinnerhal

3、b von Gebuden Teil 5: Gebrauchstauglichkeit des Systems (ISO 21003-5:2008)Englische Fassung DIN EN ISO 21003-5:2008-11www.beuth.deDocument comprises 17 pages DIN EN ISO 21003-5:2008-11 2 National foreword This standard has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and

4、 valves for the transport of fluids”, Subcommittee SC 2 “Plastics pipes and fittings for water supplies” (Secretariat: SNV, Switzerland) in collaboration with Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” (Secretariat: NEN, Netherlands). The responsible German body inv

5、olved in its preparation was the Normenausschuss Wasserwesen (Water Practice Standards Committee), Technical Committee NA 119-04-06-06 GUA Kunststoffrohre in der Trink-wasserversorgung; Mehrschichtrohrsysteme. The International Standards referred to in clause 2 of this document have been published a

6、s the correspond-ing DIN EN or DIN EN ISO Standards with the same number: ISO 1167-1 DIN EN ISO 1167-1 ISO 1167-2 DIN EN ISO 1167-2 ISO 1167-3 DIN EN ISO 1167-3 ISO 1167-4 DIN EN ISO 1167-4 ISO 13760 DIN EN ISO 13760 ISO 15874-5 DIN EN ISO 15874-5 ISO 15875-5 DIN EN ISO 15875-5 ISO 15876-5 DIN EN IS

7、O 15876-5 ISO 15877-5 DIN EN ISO 15877-5 ISO 21003-1 DIN EN ISO 21003-1 ISO 21003-2 DIN EN ISO 21003-2 ISO 21003-3 DIN EN ISO 21003-3 ISO/TS 21003-7 DIN ISO/TS 21003-7 National Annex NA (informative) Bibliography DIN EN ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of

8、fluids Determination of the resistance to internal pressure Part 1: General method DIN EN ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 2: Preparation of pipe test pieces DIN EN ISO 1167-3, Thermoplast

9、ics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components DIN EN ISO 1167-4, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Pa

10、rt 4: Preparation of assemblies DIN EN ISO 13760, Plastics pipes for the conveyance of fluids under pressure Miners rule Calculation method for cumulative damage DIN EN ISO 21003-5:2008-11 3 DIN EN ISO 15874-5, Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 5: F

11、itness for purpose of the system DIN EN ISO 15875-5, Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 5: Fitness for purpose of the system DIN EN ISO 15876-5, Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 5: Fitne

12、ss for purpose of the system DIN EN ISO 15877-5, Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 5: Fitness for purpose of the system DIN EN ISO 21003-1, Multilayer piping systems for hot and cold water installations inside buildings Part 1:

13、 General DIN EN ISO 21003-2, Multilayer piping systems for hot and cold water installations inside buildings Part 2: Pipes DIN EN ISO 21003-3, Multilayer piping systems for hot and cold water installations inside buildings Part 3: Fittings DIN ISO/TS 21003-7, Multilayer piping systems for hot and co

14、ld water installations inside buildings Part 7: Guidance for the assessment of conformity DIN EN ISO 21003-5:2008-11 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 21003-5 July 2008 ICS 23.040.01; 91.140.60 English Version Multilayer piping systems for ho

15、t and cold water installations inside buildings - Part 5: Fitness for purpose of the system (ISO 21003-5:2008) Systmes de canalisations multicouches pour installations deau chaude et froide lintrieur des btiments - Partie 5: Aptitude lemploi du systme (ISO 21003-5:2008) Mehrschichtverbund-Rohrleitun

16、gssysteme fr die Warm- und Kaltwasserinstallation innerhalb von Gebuden - Teil 5: Gebrauchstauglichkeit des Systems (ISO 21003-5:2008) This European Standard was approved by CEN on 15 June 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions

17、for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three offi

18、cial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria

19、, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTE

20、E FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 21003-5:2008: E2 EN ISO 21003-5:200

21、8 (E) DIN EN ISO 21003-5:2008-11 Contents Page Foreword3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .6 4 Symbols and abbreviated terms 6 5 Fitness for purpose of the joints and the piping system.7 5.1 General7 5.2 Internal pressure test 7 5.3 Bending test .8 5.4 Pull-

22、out test 9 5.5 Thermal cycling test . 10 5.6 Pressure cycling test 10 5.7 Leaktightness under vacuum 11 Annex A (normative) List of reference product standards 12 Bibliography. 13 3 EN ISO 21003-5:2008 (E) DIN EN ISO 21003-5:2008-11 Foreword This document (EN ISO 21003-5:2008) has been prepared by T

23、echnical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids“ in collaboration with Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN. This European Standard shall be given the status of a national s

24、tandard, either by publication of an identical text or by endorsement, at the latest by January 2009, and conflicting national standards shall be withdrawn at the latest by January 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rig

25、hts. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s). For relationsh

26、ip with EC Directive(s), see informative Annex ZA, B, C or D, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cypr

27、us, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 21

28、003-5:2008 has been approved by CEN as a EN ISO 21003-5:2008 without any modification. Introduction The system standard of which this is Part 5 specifies the requirements for a multilayer piping system. The multilayer piping system is intended to be used for hot and cold water installations inside b

29、uildings. In respect of potential adverse effects on the quality of water intended for human consumption caused by the products covered by ISO 21003: no information is provided as to whether the products may be used without restriction in any of the member states of the EU or EFTA; it should be note

30、d that, while awaiting the adoption of verifiable European criteria, existing national regulations concerning the use and/or the characteristics of these products remain in force. Requirements and test methods for components of the piping system are specified in ISO 21003-1, ISO 21003-2 and ISO 2100

31、3-3. ISO/TS 21003-7 gives guidance on the assessment of conformity. This part of ISO 21003 specifies the characteristics for fitness for purpose. For ancillary equipment, separate standards can apply. Guidance on installation of plastics piping systems made from various materials intended to be used

32、 for hot and cold water installations is given in ENV 12108. Other system standards which, at the date of publication of this part of ISO 21003, had been published for plastics piping systems used for the same application are listed in Annex A. 4 DIN EN ISO 21003-5:2008-11 EN ISO 21003-5:2008 (E) 1

33、Scope This part of ISO 21003 specifies the characteristics for the fitness for purpose of multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water whether or not the water is intended for human consumption (domestic systems) or f

34、or heating systems under specified design pressures and temperatures appropriate to the class of application (see Table 1 of ISO 21003:2008). It also specifies the test parameters for the test methods referred to in this part of ISO 21003. ISO 21003 is a reference product standard. It is applicable

35、to multilayer pipes, fittings, their joints, and also to joints with components made of other plastics and non-plastics materials intended to be used for hot and cold water installations. This part of ISO 21003 is intended for use only in conjunction with all the other parts of ISO 21003. ISO 21003

36、covers a range of service conditions (application classes) and design pressures. It is not applicable for values of design temperature, TD, maximum design temperature, Tmax, and malfunction temperature, Tmal, in excess of those in Table 1 of ISO 21003-1:2008. NOTE 1 It is the responsibility of the p

37、urchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. The polymeric materials used for the stress-designed layers are the following: polybutylene (PB),

38、polyethylene of raised temperature resistance (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP) and chlorinated poly(vinyl chloride) (PVC-C). The PE-X used shall be fully crosslinked and shall comply with the requirements of the relevant reference product standard (ISO 15875). NOTE 2 For

39、the purposes of this ISO 21003, crosslinked polyethylene (PE-X) as well as adhesives are considered as thermoplastic materials. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For

40、undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method ISO 1167-2, Thermoplastics pipes, f

41、ittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 2: Preparation of pipe test pieces 5 EN ISO 21003-5:2008 (E) DIN EN ISO 21003-5:2008-11 ISO 1167-3, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination o

42、f the resistance to internal pressure Part 3: Preparation of components ISO 1167-4, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies ISO 13760, Plastics pipes for the conveyance of fluids

43、 under pressure Miners rule Calculation method for cumulative damage ISO 15874-5, Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 5: Fitness for purpose of the system ISO 15875-5, Plastics piping systems for hot and cold water installations Crosslinked polyethyle

44、ne (PE-X) Part 5: Fitness for purpose of the system ISO 15876-5, Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 5: Fitness for purpose of the system ISO 15877-5, Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C)

45、 Part 5: Fitness for purpose of the system ISO 17456, Plastics piping systems Multilayer pipes Determination of long-term strength ISO 21003-1:2008, Multilayer piping systems for hot and cold water installations inside buildings Part 1: General ISO 21003-2:2008, Multilayer piping systems for hot and

46、 cold water installations inside buildings Part 2: Pipes ISO 21003-3, Multilayer piping systems for hot and cold water installations inside buildings Part 3: Fittings ISO 22391-5, Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part

47、5: Fitness for purpose of the system EN 712, Thermoplastics piping systems End-load bearing mechanical joints between pressure pipes and fittings Test method for resistance to pull-out under constant longitudinal force EN 713, Plastics piping systems Mechanical joints between fittings and polyolefin

48、 pressure pipes Test method for leaktightness under internal pressure of assemblies subjected to bending EN 12293, Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of mounted assemblies to temperature cycling EN 12294, Plastics piping sy

49、stems Systems for hot and cold water Test method for leaktightness under vacuum EN 12295, Plastics piping systems Thermoplastics pipes and associated fittings for hot and cold water Test methods for resistance of joints to pressure cycling 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 21003-1 apply. 4 Symbols and abbreviated terms For the purposes of this part of ISO 21003,