DIN EN ISO 22391-3-2010 Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3 Fittings (ISO 22391-3 2009) Ge.pdf

1、April 2010 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、91.140.60!$a?“1626128www.din.deDDIN EN ISO 22391-3Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 3: Fittings (ISO 22391-3:2009)English translation of DIN EN ISO 22391-3:2010-04Kunststoff-Rohrleitungssysteme fr die Warm- und Kal

3、twasserinstallation Polyethylen erhhter Temperaturbestndigkeit (PE-RT) Teil 3: Formstcke (ISO 22391-3:2009)Englische bersetzung von DIN EN ISO 22391-3:2010-04Systmes de canalisations en plastique pour les installations deau chaude et froide Polythylne de meilleure rsistance la temprature (PE-RT) Par

4、tie 3: Raccords (ISO 22391-3:2009)Traduction anglaise de DIN EN ISO 22391-3:2010-04www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 22 pages04.10 DIN EN ISO 22391-3:2010-04 2 A comma is used as the decimal marker. National foreword This

5、standard has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”, Subcommittee SC 2 “Plastics pipes and fittings for water supplies” (Secretariat: SNV, Switzerland) in collaboration with Technical Committee CEN/TC 155 “Plastics piping sys

6、tems and ducting systems” (Secretariat: NEN, Netherlands). The responsible German body involved in its preparation was the Normenausschuss Wasserwesen (Water Practice Standards Committee), Joint Working Committees NA 119-04-06 GA Kunststoffrohre in der Trink-wasserversorgung and NA 119-04-06-05 GUA

7、Warm- und Kaltwasserleitungen. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. ISO 22391 consists of the following parts1), under the general title P

8、lastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT): Part 1: General Part 2: Pipes Part 3: Fittings Part 5: Fitness for purpose of the system The DIN Standards corresponding to the International Standards referred to in clause 2 of the EN

9、 are as follows, whereby EN ISO Standards are only listed below if these have not been published as DIN EN ISO Standards with the same number: ISO 228-1 DIN EN ISO 228-1 ISO 1133-1 DIN EN ISO 1133-1 ISO 1167-1 DIN EN ISO 1167-1 ISO 1167-2 DIN EN ISO 1167-2 ISO 3126 DIN EN ISO 3126 ISO 7686 DIN EN IS

10、O 7686 ISO 9080 DIN EN ISO 9080 ISO 22391-1 DIN EN ISO 22391-1 ISO 22391-2 DIN EN ISO 22391-2 ISO 22391-5 DIN EN ISO 22391-5 1) This System Standard does not incorporate a Part 4: Ancillary equipment or a Part 6: Guidance for installation. For ancillary equipment, separate standards can apply. Guida

11、nce for installation of plastics piping systems made from different materials, intended to be used for hot and cold water installations, is covered by ENV 12108. DIN EN ISO 22391-3:2010-04 3 National Annex NA (informative) Bibliography DIN EN ISO 228-1, Pipe threads where pressure-tight joints are n

12、ot made on the threads Part 1: Dimen-sions, tolerances and designation DIN EN ISO 1133-1, Plastics Determination of the melt volume-flow rate (MVR) and melt mass-flow rate (MFR) of thermoplastics materials Part 1: Standard method DIN EN ISO 1167-1, Thermoplastics pipes, fittings and assemblies for t

13、he conveyance of fluids Determina-tion of the resistance to internal pressure Part 1: General method DIN EN ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determina-tion of the resistance to internal pressure Part 2: Preparation of pipe test pieces DIN EN ISO

14、3126, Plastics piping systems Plastics components Determination of dimensions DIN EN ISO 7686, Plastics pipes and fittings Determination of opacity DIN EN ISO 9080, Plastics piping and ducting systems Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by ext

15、rapolation DIN EN ISO 22391-1, Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 1: General DIN EN ISO 22391-2, Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Par

16、t 2: Pipes DIN EN ISO 22391-5, Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 5: Fitness for purpose of the system DIN EN ISO 22391-3:2010-04 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM

17、EN ISO 22391-3 December 2009 ICS 23.040.45; 91.140.60; 93.025 English Version Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3: Fittings (ISO 22391-3:2009) Systmes de canalisations en plastique pour les installations deau c

18、haude et froide - Polythylne de meilleure rsistance la temprature (PE-RT) - Partie 3: Raccords (ISO 22391-3:2009) Kunststoff-Rohrleitungssysteme fr die Warm- und Kaltwasserinstallation - Polyethylen erhhter Temperaturbestndigkeit (PE-RT) - Teil 3: Formstcke (ISO 22391-3:2009) This European Standard

19、was approved by CEN on 4 November 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such

20、 national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language

21、 and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxem

22、bourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All righ

23、ts of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 22391-3:2009: EContents Page DIN EN ISO 22391-3:2010-04 EN ISO 22391-3:2009 (E) 2 Foreword .3 Introduction.4 1 Scope5 2 Normative references5 3 Terms, definitions, symbols and abbreviated ter

24、ms .6 3.1 General fittings 6 3.2 Mechanical fittings 7 3.3 Fittings for heat fusion7 4 Material characteristics.7 4.1 Plastics fitting material .7 4.2 Metallic fitting material9 4.3 Influence on water intended for human consumption 9 5 General characteristics.9 5.1 Appearance 9 5.2 Opacity10 6 Geome

25、trical characteristics .10 6.1 General .10 6.2 Dimensions of sockets for socket fusion and electrofusion fittings.10 6.3 Dimensions of metallic fittings 13 7 Mechanical characteristics of plastics fittings.14 7.1 General .14 7.2 Fitting material identical to PE-RT compound .14 7.3 Fitting made from

26、PE-RT but not identical to PE-RT compound14 7.4 Fittings made from plastics other than PE-RT .14 8 Physical and chemical characteristics of plastics components 16 8.1 Melt mass flow rate .16 9 Sealing elements .16 10 System performance requirements.16 11 Marking.16 11.1 General requirements .16 11.2

27、 Minimum required marking 16 Bibliography18 Foreword “Plastics piping systems and ducting systems” the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 201

28、0, and conflicting national standards shall be withdrawn at the latest by June 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. A

29、ccording to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, L

30、atvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 22391-3:2009 has been approved by CEN as a EN ISO 22391-3:2009 without any modification. DIN EN ISO 22391-3:2

31、010-04 EN ISO 22391-3:2009 (E) 3 This document (EN ISO 22391-3:2009) has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids” in collaboration with Technical Committee CEN/TC 155 Introduction The System Standard, of which this is Part 3, s

32、pecifies the requirements for a piping system and its components when made from polyethylene of raised temperature resistance (PE-RT). The piping system is intended to be used for hot and cold water installations. In respect of potential adverse effects on the quality of water intended for human con

33、sumption caused by the products covered by ISO 22391, the following are relevant. a) This part of ISO 22391 provides no information as to whether the products can be used without restriction. b) Existing national regulations concerning the use and/or characteristics of the products remain in force.

34、This part of ISO 22391 specifies the general aspects of the plastics piping system. At the date of publication of this part of ISO 22391, System Standards Series for piping systems of other plastics materials used for the same application are the following: ISO 15874 (all parts), Plastics piping sys

35、tems for hot and cold water installations Polypropylene (PP) ISO 15875 (all parts), Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) ISO 15876 (all parts), Plastics piping systems for hot and cold water installations Polybutylene (PB) ISO 15877 (all parts)

36、, Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) DIN EN ISO 22391-3:2010-04 EN ISO 22391-3:2009 (E) 4 1 Scope This part of ISO 22391 specifies the characteristics of fittings for piping systems made of polyethylene of raised temperature resistan

37、ce (PE-RT), Type I, and polyethylene of raised temperature resistance (PE-RT), Type II, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not the water is intended for human consumption (domestic systems) and for heating systems, under

38、the design pressures and temperatures appropriate to the class of application according to ISO 22391-1. This part of ISO 22391 covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. In conjuncti

39、on with the other parts of ISO 22391, it is applicable to fittings made of PE-RT, as well as to those made of other materials, intended to be fitted to pipes conforming to ISO 22391-2 for hot and cold water installations, the joints of which are in accordance with ISO 22391-5. This part of ISO 22391

40、 is applicable to the following types of fitting: mechanical fittings; socket fusion fitting; electrofusion fittings; fittings with incorporated inserts. It is not applicable to values of design temperature, maximum design temperature or malfunction temperature in excess of those specified in ISO 22

41、391-1. NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. 2 Normative references The following referenced docum

42、ents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7-1, Pipe threads where pressure-tight joints are made on the threads Part

43、1: Dimensions, tolerances and designation DIN EN ISO 22391-3:2010-04 EN ISO 22391-3:2009 (E) 5 ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation ISO 1133-1, Plastics Determination of the melt volume-flow rate (MVR) and the

44、melt mass-flow rate (MFR) of thermoplastics Part 1: Standard method ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the con

45、veyance of fluids Determination of the resistance to internal pressure Part 2: Preparation of pipe test pieces ISO 3126, Plastics piping systems Plastics components Determination of dimensions ISO 7686, Plastics pipes and fittings Determination of opacity ISO 9080, Plastics piping and ducting system

46、s Determination of long-term hydrostatic strength of thermoplastic materials in pipe form by extrapolation ISO 23711, Elastomeric seals Requirements for materials for pipe joint seals used in water and drainage applications Thermoplastic elastomers ISO 22391-1:2009, Plastics piping systems for hot a

47、nd cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 1: General ISO 22391-2:2009, Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 2: Pipes ISO 22391-5, Plastics piping systems for hot and cold w

48、ater installations Polyethylene of raised temperature resistance (PE-RT) Part 5: Fitness for purpose of the system EN 681-1, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber EN 681-2, Elastomeric seals Materials requireme

49、nts for pipe joint seals used in water and drainage applications Part 2: Thermoplastic elastomers EN 1254-3, Copper and copper alloys Plumbing fittings Part 3: Fittings with compression ends for use with plastics pipes EN 10088-1, Stainless steels Part 1: List of stainless steels 3 Terms, definitions, symbols and abbreviated terms For the purposes of this document, the terms, definitions, symbols and abbreviated terms g