DIN ISO 10228-2011 Cross-country skis - Binding mounting area - Requirements for test screws (ISO 10228 2011)《对越野滑雪橇固定安装部位的试验螺钉的要求(ISO 10228-2011)》.pdf

1、October 2011 Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、 97.220.20!$tth“1818169www.din.deDDIN ISO 10228Cross-country skis Binding mounting area Requirements for test screws (ISO 10228:2011)English translation of DIN ISO 10228:2011-10Langlaufski Bindungsbefestigungsbereich Anforderungen an Prfschrauben (ISO 10228:2011)Englische bersetzung von DIN ISO 1022

3、8:2011-10Skis de fond Zone de montage de la fixation Exigences pour les vis dessai (ISO 10228:2011)Traduction anglaise de DIN ISO 10228:2011-10SupersedesDIN ISO 10228:1995-03www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 10 pages09.11

4、A comma is used as the decimal marker. DIN ISO 10228:2011-10 2Contents Page National foreword. 3 National Annex NA (informative) Bibliography. 4 Foreword. 5 Introduction 6 1 Scope. 7 2 Normative references . 7 3 Terms and definitions. 7 4 Designation . 7 5 Requirements 8 5.1 General 8 5.2 Materials

5、8 5.3 Dimensions. 8 5.4 Surface 8 5.5 Application characteristics . 8 Bibliography . 10 National foreword This standard has been prepared by Technical Committee ISO/TC 83 “Sports and recreational equipment” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the

6、Normenausschuss Sport- und Freizeitgert (Sports Equipment Standards Committee), Working Committee NA 112-03-01 AA Ski- und Snowboardsport-gerte. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN and/or DKE shall not be held resp

7、onsible for identifying any or all such patent rights. This second edition cancels and replaces the first edition (DIN ISO 10228:1995-03), which has been technically revised. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 1478 DIN EN I

8、SO 1478 ISO 2702 DIN EN ISO 2702 ISO 4042 DIN EN ISO 4042 ISO 4757 DIN EN ISO 4757 ISO 7794 DIN ISO 7794 ISO 7795 DIN ISO 7795 Amendments This standard differs from DIN ISO 10228:1995-03 as follows: a) in Subclause 5.3.1, the requirements for the screw head have been brought in line with ISO 4757; b

9、) in Subclause 5.3.2, the requirements for the thread and end configuration have been revised; c) in Subclause 5.4, the requirements for the surface have been rendered more precise. Previous editions DIN ISO 10228: 1995-03 DIN ISO 10228:2011-10 3National Annex NA (informative) Bibliography DIN EN IS

10、O 1478, Tapping screw thread DIN EN ISO 2702, Heat-treated steel tapping screws Mechanical properties DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 4757, Cross recesses for screws DIN ISO 7794, Cross-country skis Ski-binding screws Requirements DIN ISO 7795, Cross-country skis Ski-bin

11、ding screws Test methods DIN ISO 10228:2011-10 4Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each m

12、ember body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International

13、Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards a

14、dopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of p

15、atent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10228 was prepared by Technical Committee ISO/TC 83, Sports and recreational equipment, Subcommittee SC 4, Snowsports equipment. This second edition cancels and replaces the first edition (ISO 10228:19

16、91), which has been technically revised. DIN ISO 10228:2011-10 5Introduction The use of test screws ensures the comparability of measurement data, which are determined by the manufacturer or other institutions by testing the binding mounting area of cross-country skis. DIN ISO 10228:2011-10 6Cross-c

17、ountry skis Binding mounting area Requirements for test screws 1 Scope This International Standard specifies the dimensions, mechanical properties and fastening characteristics of test screws used for testing the binding mounting area of cross-country skis. 2 Normative references The following refer

18、enced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1478, Tapping screws thread ISO 2702, Heat-treated steel tapping

19、 screws Mechanical properties ISO 7794, Cross-country skis Ski-binding screws Requirements ISO 7795, Cross-country skis Ski-binding screws Test methods 3 Terms and definitions For the purposes of this document, the definitions given in ISO 7794 and the following apply. 3.1 test screw fastener, which

20、 is used for testing the binding mounting area to ensure the comparability of measurement data 4 Designation Test screws in accordance with this International Standard shall be designated by: a) the words “Test screw”; b) the reference to this International Standard, i.e. ISO 10228; c) their nominal

21、 dimensions, i.e. diameter length. EXAMPLE Test screws with a nominal diameter of 6,3 mm and a length of 18 mm would be designated: Test screw ISO 10228 6,3 18 DIN ISO 10228:2011-10 75 Requirements 5.1 General The strength requirements and typical application characteristics of cross-country ski-bin

22、ding test screws shall be tested in accordance with ISO 7795. 5.2 Materials Test screws shall be made of steel as specified in ISO 2702, which shall comply with the additional requirements in 5.4 and 5.5 of this International Standard. 5.3 Dimensions 5.3.1 Screw head Test screws shall be cross reces

23、s type Z No. 3 with a recommended minimum penetration depth of 2,72 mm to 3,18 mm (see ISO 4757). If screws having countersunk heads are used, the angle of countersinking 2090+ is recommended. 5.3.2 Thread and end configuration The cross-section of the test screw may be circular or non-circular with

24、in the major diameter of 00,156,3 mm mm(see Figure 1). The thread length shall be at least 1 mm longer than the penetration depth, irrespective of the shaft length. The tolerance on the length of the screw shall be 0,6 mm. The shaft end shall correspond to Figure 1. 5.4 Surface Test screws shall be

25、coated or plated with materials which provide adequate protection against corrosion and ensure a reproducible coefficient of friction. For example, a suitable coating would be a zinc electroplated coating, Fe/Zn 5c (see ISO 4042), having a clear chromate conversion coating and a minimum local thickn

26、ess of 5 m (batch average 4 min., 6 m max.), when measured on the top surface of the screw head. During electroplating, adequate precautions shall be taken to avoid hydrogen embrittlement. 5.5 Application characteristics 5.5.1 General The specified fastening and mounting characteristics of the test

27、screw shall be based on a uniform drill diameter of 0,1503,6 mm mm.+5.5.2 Strength requirements The breaking moment for test screws under a torque of the same axis and direction as the driving torque shall be not less than 10 Nm. The screws shall not break when subjected to the conditions of the duc

28、tility test. DIN ISO 10228:2011-10 85.5.3 Fastening characteristics The mean static pull-out resistance shall correspond to at least that of a reference screw complying with the requirements of ISO 1478, type F, and having a nominal diameter of 6,3 mm. Dimensions in millimetres aCross-recess type Z No. 3 in accordance with ISO 4757. bPitch. Figure 1 Head, thread and end configuration DIN ISO 10228:2011-10 9Bibliography 1 ISO 4042, Fasteners Electroplated coatings 2 ISO 4757, Cross recesses for screws DIN ISO 10228:2011-10 10