DIN ISO 10897-2006 Collets for tool holders with taper ratio 1 10 - Collets holders nuts (ISO 10897 1996) English version of DIN ISO 10897 2006-01《刀具夹用1 10锥度的夹头 夹头、夹柄和螺母》.pdf

1、 DEUTSCHE NORM January 2006DIN ISO 10897 ICS 25.060.20 Supersedes DIN 6388:1993-02 Collets for tool holders with taper ratio 1:10 Collets, holders, nuts (ISO 10897:1996) English version of DIN ISO 10897:2006-01 Spannzangen mit Kegelverhltnis 1:10 fr Werkzeugspannung Spannzangen, Spannzangenaufnahmen

2、, Spannmuttern (ISO 10897:1996) Englische Fassung DIN ISO 10897:2006-01 Document comprises 16 pages No part of this standard may be reproduced without prior permission of DIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, has the exclusive right of sale for Ge

3、rman Standards (DIN-Normen). English price group 10 www.din.de www.beuth.de !,jX“06.06 9715304DIN ISO 10897:2006-01 2 National foreword This standard has been prepared by ISO/TC 29 Small tools. The responsible German body involved in its preparation was the Normenausschuss Werkzeuge und Spann-zeuge

4、(Tools and Clamping Devices Standards Committee), Technical Committee NA 121-10-10 AA Spann-zangen. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. T

5、he DIN Standard corresponding to the International Standard referred to in clause 2 of the ISO Standard is as follows: ISO 2768-1 DIN ISO 2768-1 Amendments This standard differs from DIN 6388, February 1993 edition, as follows: a) The standard has been superseded by the specifications of ISO 10897:1

6、996. Previous editions DIN 6388: 1986-07, 1993-02 National Annex NA (informative) Bibliography DIN ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 10897:1996 (E)1Collets for tool holders with taper ratio 1 :I0 - Collets

7、, holders, nuts Contents Page 1 Scope 3 2 Normative reference3 3 Dimensions 3 3.1 Collets.4 3.2 Holder6 3.3 Nut.7 3.4 Collet run-out tolerances 8 4 Material .9 4.1 Collet.9 4.2 Nut.9 5 Manufacturing requirements 10 5.1 Collet.10 5.2 Holder10 5.3 Nut.10 6 Designation 10 6.1 Collet.10 6.2 Holder11 6.3

8、 Nut.11 6.4 Test mandrel 11 7 Marking .12 8 Operational set-up.12 Annex A (normative) Cone angle tolerances AT3 and AT4 14 Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International

9、 Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, a

10、lso take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Interna

11、tional Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0 10897 was prepared by Technical Committee ISO/TC 29, Small fools. Annex A forms an integral part of this International Standard. ISO 10897:1996 (E)21 Scope This International Standard s

12、pecifies the dimensions, materials and manufacturing requirements, and designation of collets for tools with cylindrical shanks and their corresponding holders and nuts. For non- standardized clamping devices, such as clamping devices specified in drawings, these holders can be agreed upon between c

13、ustomer and supplier. Form A applies where a clamping range of h10 is sufficient. Form B can be used for any application without lateral cutting load. 2 Normative reference The following standard contains provisions which, through reference in this text, constitute provisions of this International S

14、tandard. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent edition of the standard indicated below. Members of IE

15、C and IS0 maintain registers of currently valid International Standards. IS0 2768-l :I 989, General tolerances - Part I: Tolerances for linear and angular dimensions without individual tolerance indications. 3 Dimensions Collets, holders and nuts need not correspond to figures 1 to 4; only the given

16、 dimensions shall be complied with. General tolerances: IS0 2768-l - m ISO 10897:1996 (E)33.1 Collets See figures 1 and 2 and table 2. /Field for marking Tolerances in millimetres, surface roughness in micrometres L - - Figure 1 - Collet form A, unilaterally slotted, with short clamping bore for cyl

17、indrical shanks / Field for marking NOTE - Other dimensions and tolerances as form A. Figure 2 - Collet form B, bilaterally slotted, with continuous clamping bore for cylindrical shanks ISO 10897:1996 (E)4Table 1 - Collet dimensions Dimensions in millimetres 4 0 - 0,l d3 0 - 0,05 I dl d2 5 d4 + 0,l

18、0 7 3 6 xk 0,2 6 7 65 8 IO IO 11 12 13,5 17 Nominal size H7 Form Al) Form B 2, Nominal diameter 4 6 II,5 IO,0 21 395 075 8 12,65 14,5 818 26 495 4 098 10 15,15 17,2 IO,2 30 4,5 45 08 12 1 12 - - 17,75 19,8 12,3 34 495 5 171 53 16 2 1 16 1 5 1 16 I22,65 25,5 16,l 40 575 W 12 20 2 / 20 1 6 / 20 1 27,4

19、 29,8 20,3 45 6 IO 6 I,35 25 35,05 25,l 52 6 IO 6 194 2 25 6 25 32,9 4 32 IO 32 41,3 43,7 32,l 60 7 11 6 I,45 32 6 29,5 30 40 I 49,7 I I I I 1 8 j 29,5 / 30 j 50 1 61, 40 52,2 39,5 68 8 12 6 I,45 63,8 49,5 80 9 13 7 I,55 50 ) For clamping range hl0. !) For clamping range -i 5 . 7 ISO 10897:1996 (E)5

20、3.2 Holder See figure 3 and table 2. /Rz 2,s I- rl l8 c Tolerances in millimetres, surface roughness in micrometres Transition at n lanufacturers option -/ 9 30” max. Figure 3 - Holder form C Table 2 - Holder dimensions Dimensions in miilimetres Nominal size 6 8 Id 12 16 20 25 32 40 50 d2 H7 IO 12,6

21、5 15,15 17,75 22,65 27,4 32,9 41,3 49,7 61,l d5 b) cylindricity: 0,002 mm; c) parallelism: 0,002 mm; d) roundness: 0,002 mm; e) surface without longitudinal marks; f) maximum surface roughness Rz= 4 urn; g) surface hardness: (58 g) HRC. Key 1 1 6 -. _. . - _ - 8 1) Test mandrel 2) Test point Figure

22、5 - Testing of run-out ISO 10897:1996 (E)8Table 4 - Collet run-out tolerance values Dimensions in millimetres dl l-l7 Nominal diameter 16 Run-out tolerance I) above up to (included) Class 1 Class 2 I (included) 16 6 16 3 IO 3 6 16 0,Ol 0,015 6 IO 25 IO 18 40 18 24 50 0,015 0,02 24 30 60 30 50 80 0,0

23、2 0,03 NOTE - In the case of applications where run-out tolerances class 1 are required the accuracy of the whole system (machine tool spindle, holder, collet and tool) shall be observed. 1) Normal style collets are designed with run-out tolerance class 2. If class 1 is required, it shall be given s

24、eparately, see 5.1. 4 Material 4.1 Collet Steel at manufacturers discretion with a tensile strength of at least 700 N/mm? 4.2 Nut Steel at manufacturers discretion. ISO 10897:1996 (E)95 Manufacturing requirements 5.1 Collet Collet form A : bore and taper hardened, hardness (56 z) HRC. Collet form B

25、: bore and taper hardened, hardness (44 ;f) HRC. Tolerances of taper : AT3 in accordance with table A.1 . Run-out tolerance : class 2, for normal styles. 5.2 Holder Taper bore hardened, hardness (58 z) HRC. Tolerances of taper : AT4 in accordance with table A.2. 5.3 Nut Design at manufacturers discr

26、etion. 6 Designation 6.1 Collet A collet in accordance with this International Standard shall be designated by a) “Collet”; b) reference to this International Standard; c) form (A or B); d) nominal size; e) nominal diameter, dl in millimetres; f) run-out tolerance in the case of class 1. EXAMPLES A

27、collet of form A nominal size 32 and nominal diameter dl = IO mm is designated as follows: Collet IS0 10897 - A 32 x 10 A collet of form A, nominal size 32, nominal diameter dl = IO mm and of run-out tolerance class 1 is designated as follows: Collet IS0 10897 - A 32 x 10 Cl1 ISO 10897:1996 (E)106.2

28、 Holder A holder in accordance with this international Standard shall be designated by a) “Holder”; b) reference to this International Standard; c) form C; d) nominal size. EXAMPLE A holder of form C and nominal size 32 is designated as follows: Holder IS0 10897 - C 32 6.3 Nut A nut in accordance wi

29、th this International Standard shall be designated by: a) “Nut”; b) reference to this International Standard; c) form D; d) nominal size. EXAMPLE A nut of form D and nominal size 32 is designated as follows: Nut IS0 10897 - D 32 6.4 Test mandrel A test mandrel in accordance with this International S

30、tandard shall be designated by a b) C “Test mandrel”; reference to this International Standard; diameter, dl in millimetres. EXAMPLE A test mandrel of diameter dl = 10 mm is designated as follows: Test mandrel IS0 10897 - 10 ISO 10897:1996 (E)117 Marking Collets in accordance with this International

31、 Standard shall be marked with: - relevant nominal diameter; - name or trademark of the manufacturer. 8 Operational set-up See figure 6 and table 5. yForm * -I T Form B Figure 6 - Example of operational set-up ISO 10897:1996 (E)12Nominal size 6 775 8 815 10 12 16 II 15 20 25 12 16 32 13 40 50 Table

32、5 - Dimensions Dimensions in millimetres 17 max. 9 93 12 16 14 16 18 max. 17 18 20 ISO 10897:1996 (E)13Annex A (normative) Cone angle tolerances AT3 and AT4 This annex specifies the values for AT3 tolerance (see table A.l) and AT4 tolerance (see table A.2) from IS0 194711973, System of cone toleranc

33、es for conical workpieces form C = I:3 to I:500 and lengths from 6 to 630 mm, which has been withdrawn. Table A.1 - Cone angle tolerance AT 3 Range of cone lengths L mm over up to 6 10 10 16 16 25 80 16 1 I,3 . . 2 25 40 63 40 63 ATa ATg) prad seconds I-Jm 125 26 1 0,8 . . I,3 100 21 l 1 . . . . 176

34、 1 50 10 2 . . . . . 392 13 I,6 . . 2,5 1) ATD is calculated from the constant ATa value within a range of cone lengths. Tableau A.2 - Cone angle tolerance AT4 Range of cone lengths L mm ATa ATD) over 6 up to 10 prad 200 seconds 41 I-Jm I,3 . . . 2 10 16 160 33 I,6 . . . 2,5 16 25 125 26 2 . . . . . . 32 25 40 100 21 2,5 . . . 4 40 I 63 I 80 I 16 I 3,2 . . . 5 I 1) ATD is calculated from the constant AT, value within a range of cone lengths. ISO 10897:1996 (E)14