DIN ISO 12164-4-2016 Hollow taper interface with flange contact surface - Part 4 Dimensions of receivers for stationary tools (ISO 12164-4 2014)《带法兰连接表面的中空锥形接口 第4部分 固定式工具承受器的尺寸(ISO.pdf

1、October 2016 English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 25.060.20!%nc“2577564www.din.deDI

2、N ISO 12164-4Hollow taper interface with flange contact surface Part 4: Dimensions of receivers for stationary tools (ISO 121644:2014),English translation of DIN ISO 12164-4:2016-10Hohlkegelschnittstelle mit Plananlage Teil 4: Mae von Aufnahmen fr stehende Werkzeuge (ISO 121644:2014),Englische berse

3、tzung von DIN ISO 12164-4:2016-10Interfaces cne creuxface Partie 4: Dimensions des nez de broches pour outils non rotatifs (ISO 121644:2014),Traduction anglaise de DIN ISO 12164-4:2016-10www.beuth.deDocument comprises 9 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language or

4、iginal shall be considered authoritative.09.16 A comma is used as the decimal marker. Contents PageNational foreword31 Scope .42 Normative references 43 Dimensions .43.1 General .43.2 Receiver for hollow taper shank, type T .44 Design Hole for manual clamping .65 Designation 6Annex A (informative) R

5、ecommendations for use and application .8Bibliography 9National Annex NA (informative) Bibliography .3DIN ISO 12164-4:2016-102 National foreword This document (ISO 12164-4:2014) has been prepared by Technical Committee ISO/TC 29 “Small tools (Secretariat: AFNOR, France). The responsible German body

6、involved in its preparation was DIN-Normenausschuss Werkzeuge und Spannzeuge (DIN Standards Committee Tools and Clamping Devices), Working Committee NA 121-02-05 AA Werkzeugaufnahmen und Schnittstelle Maschine/Werkzeug. Attention is drawn to the possibility that some of the elements of this document

7、 may be the subject of patent rights. DIN and/or DKE shall not be held responsible for identifying any or all such patent rights. ISO 12164 consists of the following parts, under the general title Hollow taper interface with flange contact surface: Part 1: Shanks Dimensions Part 2: Receivers Dimensi

8、ons Part 3: Dimensions of shanks for stationary tools Part 4: Dimensions of receivers for stationary tools The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 1101 DIN EN ISO 1101 ISO 2768-1 DIN ISO 2768-1 ISO 3040 DIN EN ISO 3040 National

9、Annex NA(informative) Bibliography DIN EN ISO 1101, Geometrical Product Specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and run-out DIN ISO 2768-1, General tolerances; tolerances for linear and angular dimensions without individual tolerance indications DIN EN

10、ISO 3040, Geometrical product specifications (GPS) Dimensioning and tolerancing Cones DIN ISO 12164-4:2016-103 Hollow taper interface with flange contact surface Part 4: Dimensions of receivers for stationary tools1 ScopeThis part of ISO 12164 specifies dimensions for receivers with taper and flange

11、 contact surfaces for hollow taper shanks in accordance with ISO 12164-3 to be applied to machine tools (e.g. turning machines, turning-mill machines). A range of sizes is specified.This part of ISO 12164 specifies the receiver of type T. It is for automatic tool exchange and manual clamping, which

12、is achieved via holes in both the receiver and the tool shank.The torque is transmitted via the tail end of the shank through keys as well as friction.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its applica

13、tion. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 1101, Geometrical product specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and run-outISO 276

14、8-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indicationsISO 3040, Geometrical product specifications (GPS) Dimensioning and tolerancing Cones3 Dimensions3.1 GeneralDimensions of receivers for hollow taper shanks with flange contact surface

15、 for stationary tools, type T, are specified in Figure 1, Table 1, and Annex A. Details not specified in Figures 1 shall be chosen expediently. Tolerancing of form, orientation, location, and run-out is in accordance with ISO 1101. Dimensioning and tolerancing of cones are in accordance with ISO 304

16、0. Tolerances not specified shall be of tolerance class m in accordance with ISO 2768-1.3.2 Receiver for hollow taper shank, type TThe dimensions of receiver for hollow taper shanks, type T, shall be in conformance with Figure 1 and Table 1.DIN ISO 12164-4:2016-104 Dimensions in millimetres Surface

17、roughness values in micrometresKey1 cutting edgeb2 tenonc3 hole for manual clampingdaWhen tenons are inserted, the taper hole may be conical over the total length l1.bPosition of the cutting edge for right-hand tools with single cutting edged.cTenon alternative integrated or inserted.dInside edge mi

18、n. 0,5 mm 45 chamfer.Figure 1 Dimensions of receiversDIN ISO 12164-4:2016-105N1)N1)National footnote: NC not convex Table 1 DimensionsDimensions in millimetresNominal size 32 40 50 63 80 100 125 160b10,05 6,8 7,8 10,3 12,3 15,8 19,78 24,78 29,78b26,92 7,92 10,41 12,41 15,91 19,89 24,89 29,89tol.0 02

19、50, 0030,d1min. 32 40 50 63 80 100 125 160d223,998 29,998 37,998 47,998 59,997 74,997 94,996 119,995d3a17 21 26 34 42 53 67 85d4b001+ ,23,28 29,06 36,85 46,53 58,1 72,6 92,05 116,1d5002+ ,23,8 29,6 37,5 47,2 58,8 73,4 93 118d6Hole diameter to be chosen by the manufacturerl1b002+ ,16,5 20,5 25,5 33 4

20、1 51 64 81l23,2 4 5 6,3 8 10 12,5 16l3002+ ,11,4 14,4 17,9 22,4 28,4 35,4 44,4 57,4l4002+ ,13,4 16,9 20,9 26,4 32,4 40,4 51,4 64,4l50,8 0,8 1 1 1,5 1,5 2 2l6001+ ,1 1 1,5 1,5 2 2 2,5 2,5l70,1 2 2 2 2,5 3 3 4 4l80,1 5 6 7,5 9 12 15 r1c0050,1,5 2 2,5 3 4 5 6 8t 0,001 5 0,001 5 0,002 0,002 0,002 5 0,00

21、3 0,003 5 0,003 5aDepending on the clamping system.bSee note ato Figure 1.cr1tangent to b1or b2and d4.4 Design Hole for manual clampingDesign without hole for manual clamping is standard.Design with hole for manual clamping is optional.5 DesignationA receiver for hollow taper shank (HSK) in accordan

22、ce with this part of ISO 12164 shall be designated by the following:a) “Receiver for hollow taper shank”;DIN ISO 12164-4:2016-106 b) reference to this part of ISO 12164, i.e. ISO 12164-4;c) “HSK”;d) type: T for stationary tools;e) nominal size, in millimetres.EXAMPLE A receiver for hollow taper shan

23、k with flange contact surface (HSK) for stationary tools (type T) with nominal size 50 mm is designated as follows:Receiver for hollow taper shank ISO 12164-4-HSK-T 50DIN ISO 12164-4:2016-107 Annex A (informative) Recommendations for use and applicationA.1 Clamping systemThe clamping system should b

24、e specified by the manufacturer of the receiver or machine tool spindle. The system should provide sufficient clamping force to ensure contact of the shank flange with the receiver face, as well as seating of the taper by elastic deformation. The torque transmitting capacity of the interface is subs

25、tantially determined by the size of the clamping force.A.2 Clamping forcesThe recommended clamping forces are shown in Table A.1.The clamping forces are only applied to the hollow shanks for stationary tools (type T).Table A.1Nominal size, mm 32 40 50 63 80 100 125 160Clamping force, kN 5 8 14 24 37

26、 55 86 150Lower clamping forces can be sufficient when operational loads are low (e.g. cutting and feed forces in finish machining). Conversely, higher clamping forces can be required when high operational loads are encountered (e.g. cutting and feed forces in heavy machining).A.3 Information about

27、speeds and torqueThe manufacturer should provide information regarding permissible speeds and torque transmitting capacities.DIN ISO 12164-4:2016-108 Bibliography1 ISO 12164-3, Hollow taper interface with flange contact surface Part 3: Dimensions of shanks for stationary toolsDIN ISO 12164-4:2016-109