DIN ISO 13012-2-2010 Rolling bearings - Accessories for sleeve type linear ball bearings - Part 2 Boundary dimensions and tolerances for series 5 (ISO 13012-2 2009)《滚动轴承 套筒型线性滚珠轴承用.pdf

1、February 2010DEUTSCHE NORM English price group 11No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 21.100.20!$,*“1570907

2、www.din.deDDIN ISO 13012-2Rolling bearings Accessories for sleeve type linear ball bearings Part 2: Boundary dimensions and tolerances for series 5(ISO 13012-2:2009)English version of DIN ISO 13012-2:2010-02Wlzlager Zubehr fr Linearkugellager in Hlsenform Teil 2: Hauptmae und Toleranzen fr Reihe 5 (

3、ISO 13012-2:2009)Englische Fassung DIN ISO 13012-2:2010-02supersedesDIN ISO 13012:1999-12www.beuth.deDocument comprises 17 pages13012-1:2010-02,Together with DIN ISO02.10 2 Contents Page National foreword .3 National Annex NA (informative) Bibliography 4 Introduction.5 1 Scope 6 2 Normative referenc

4、es 6 3 Terms and definitions .7 4 Symbols 8 4.1 Closed and adjustable flangeless housings for series 5 sleeve type linear ball bearings8 4.2 Open and open adjustable flangeless housings for series 5 sleeve type linear ball bearings8 4.3 Standard height shaft support rails for series 5 sleeve type li

5、near ball bearings9 4.4 Flanged shaft support blocks for series 5 sleeve type linear ball bearings9 4.5 Solid and tubular shafts for series 5 sleeve type linear ball bearings.9 5 Housings 10 5.1 General. 10 5.2 Housings for series 5 sleeve type linear ball bearings. 10 6 Shaft support rails 10 7 Sha

6、ft support blocks 10 8 Shafts . 10 8.1 Material 10 8.2 Heat treatment. 10 8.3 Geometrical tolerances 11 9 Boundary dimensions and tolerances . 11 9.1 Housings 11 9.2 Shaft support rails 14 9.3 Shaft support blocks 15 9.4 Shafts . 16 DIN ISO 13012-2:2010-02 DIN ISO 13012-2:2010-02 3 National foreword

7、 This standard has been prepared by Technical Committee ISO/TC 4 “Rolling bearings”, Subcommittee SC 11 “Linear motion rolling bearings” (Secretariat: ANSI, USA). The responsible German body involved in its preparation was the Normenausschuss Wlz- und Gleitlager (Rolling Bearings and Plain Bearings

8、Standards Committee), Working Committee NA 118-01-11 AA Linear-Wlzlager einschlielich Teile und Zubehr. DIN ISO 13012 consists of the following parts, under the general title Rolling bearings Accessories for sleeve type linear ball bearings: Part 1: Boundary dimensions and tolerances for series 1 an

9、d 3 Part 2: Boundary dimensions and tolerances for series 5 The DIN Standards corresponding to the International Standards referred to in clause 2 of the ISO Standard are as follows: ISO 286-2 DIN ISO 286-2 ISO 1132-1 DIN ISO 1132-1 ISO 1302 DIN EN ISO 1302 ISO 5593 DIN ISO 5593 ISO 10285 DIN ISO 10

10、285 ISO 13012-1 DIN ISO 13012-1 Amendments This standard differs from DIN ISO 13012:1999-12 as follows: a) Some terms and definitions relating to accessories for sleeve type linear ball bearings have been added. b) Boundary dimensions for closed and adjustable flangeless housings for series 5 sleeve

11、 type linear ball bearings have been included. c) Boundary dimensions for open and open adjustable flangeless housings for series 5 sleeve type linear ball bearings have been included. d) Boundary dimensions for standard height shaft support rails for series 5 sleeve type linear ball bearings have b

12、een included. e) Boundary dimensions for flanged shaft support blocks for series 5 sleeve type linear ball bearings have been included. f) Boundary dimensions for solid and tubular shafts for series 5 sleeve type linear ball bearings have been included. Previous editions DIN ISO 13012: 1999-12 4 Nat

13、ional Annex NA (informative) Bibliography DIN ISO 286-2, ISO system of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts DIN ISO 1132-1, Rolling bearings Tolerances Part 1: Terms and definitions DIN ISO 5593, Rolling bearings Vocabulary DIN ISO 102

14、85, Rolling bearings Sleeve type linear ball bearings Boundary dimensions and tolerances DIN ISO 13012-1, Rolling bearings Accessories for sleeve type linear ball bearings Part 1: Boundary dimensions and tolerances for series 1 and 3 DIN EN ISO 1302, Geometrical Product Specifications (GPS) Indicati

15、on of surface texture in technical product documentation DIN ISO 13012-2:2010-02 Introduction The use of sleeve type linear ball bearings can be facilitated by the selection of bearing housings, shafts, shaft support blocks and shaft support rails. These items, referred to as accessories, can aid in

16、 the application of the sleeve type linear ball bearings to achieve the desired criteria of smooth, accurate, low-friction linear motion free from chatter or stick-slip. The appropriate selection of bearing housing type, shaft and shaft support should be established between the manufacturer and the

17、user. This part of ISO 13012 was developed to be used with ISO 10285. 5 Rolling bearings Accessories for sleeve type linear ball bearings Part 2: Boundary dimensions and tolerances for series 5 DIN ISO 13012-2:2010-02 1 Scope This part of ISO 13012 specifies the boundary dimensions, other relevant d

18、imensions and their tolerances of accessories for sleeve type linear ball bearings which are specified in ISO 10285. This part of ISO 13012 applies to: housings closed and adjustable flangeless housings for series 5 sleeve type linear ball bearings, open and open adjustable flangeless housings for s

19、eries 5 sleeve type linear ball bearings; shaft support rails standard height shaft support rails for series 5 sleeve type linear ball bearings; shaft support blocks flanged shaft support blocks for series 5 sleeve type linear ball bearings; shafts solid and tubular shafts for series 5 sleeve type l

20、inear ball bearings. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2

21、86-2, ISO system of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts ISO 1132-1, Rolling bearings Tolerances Part 1: Terms and definitions ISO 1302, Geometrical Product Specifications (GPS) Indications of surface texture in technical product docum

22、entation ISO 3754, Steel Determination of effective depth of hardening after flame or induction hardening ISO 5593, Rolling bearings Vocabulary ISO 10285:2007, Rolling bearings Sleeve type linear ball bearings Boundary dimensions and tolerances ISO 15241, Rolling bearings Symbols for quantities ISO

23、24393, Rolling bearings Linear motion rolling bearings Vocabulary 6 DIN ISO 13012-2:2010-02 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 1132-1, ISO 5593, ISO 10285, and ISO 24393 apply. 3.1 flangeless housing sleeve type linear ball bearing beari

24、ng housing which has a face with bolt holes or threaded holes for attachment to a support surface nominally parallel to the bearing axis ISO 13012-1:2009 3.2 closed housing sleeve type linear ball bearing bearing housing in which the bearing seating is circumferentially continuous ISO 13012-1:2009 3

25、.3 adjustable housing sleeve type linear ball bearing bearing housing with a longitudinal slit across its bearing seating which facilitates the mechanical adjustment of the bearing seating diameter ISO 13012-1:2009 3.4 open housing sleeve type linear ball bearing bearing housing with a longitudinal

26、section removed to provide clearance over a shaft and support rail unit ISO 13012-1:2009 3.5 open adjustable housing sleeve type linear ball bearing bearing housing which has the features of both open and adjustable sleeve type linear ball bearing housings ISO 13012-1:2009 3.6 shaft support rail lon

27、gitudinal pedestal which provides continuous support to a shaft NOTE Shaft support rails may be used with open sleeve type linear ball bearings. ISO 13012-1:2009 3.7 shaft support block block which provides support to a shaft NOTE Shaft support blocks are normally used to support the shaft at its en

28、ds and can be used with closed sleeve type, adjustable sleeve type or open sleeve type linear ball bearings. ISO 13012-1:2009 3.8 shaft basically cylindrical rod along which a linear ball bearing traverses ISO 13012-1:2009 7 DIN ISO 13012-2:2010-02 4 Symbols For the purposes of this document, the sy

29、mbols given in ISO 15241 and the following apply. The symbols (except those for tolerances) shown in Figures 1 to 5, and the values given in Tables 1 to 6 denote nominal dimensions unless specified otherwise. NOTE Figures 1 to 5 are drawn schematically and do not necessarily show all design details.

30、 4.1 Closed and adjustable flangeless housings for series 5 sleeve type linear ball bearings See Table 1 and Figure 1. A (overall) width Daseating diameter Fwbore diameter of ball complement of sleeve type linear ball bearing (reference) G designation of screw thread of attachment hole H distance fr

31、om mounting face to centreline of seating diameter H1(overall) height J centre distance between bolt holes (length) J1centre distance between bolt holes (width) L length of housing L1distance from side face to centreline of seating diameter N diameter of bolt hole 4.2 Open and open adjustable flange

32、less housings for series 5 sleeve type linear ball bearings See Table 2 and Figure 2. A (overall) width Daseating diameter E width of sector opening (at diameter Da) Fwbore diameter of ball complement of sleeve type linear ball bearing (reference) G designation of screw thread of attachment hole H d

33、istance from mounting face to centreline of seating diameter H1(overall) height J centre distance between bolt holes (length) J1centre distance between bolt holes (width) L length of housing L1distance from side face to centreline of seating diameter angle of sector opening 8 DIN ISO 13012-2:2010-02

34、 4.3 Standard height shaft support rails for series 5 sleeve type linear ball bearings See Table 3 and Figure 3. A (overall) width d outside diameter of shaft (reference) H distance from mounting face to centreline of shaft H1height of flange J centre distance between bolt holes (length) J1centre di

35、stance between bolt holes (width) M width of shaft support N diameter of bolt hole N1diameter of bolt hole (shaft attachment) angle of shaft support 4.4 Flanged shaft support blocks for series 5 sleeve type linear ball bearings See Table 4 and Figure 4. A (overall) width Daseating diameter H distanc

36、e from mounting face to centreline of seating diameter H1height of flange H2(overall) height J centre distance between bolt holes (length) L length of base N diameter of bolt hole 4.5 Solid and tubular shafts for series 5 sleeve type linear ball bearings See Tables 5 and 6, and Figure 5 d outside di

37、ameter of shaft dssingle outside diameter of shaft L length of shaft Lsactual length of shaft t straightness of shaft Vdmpvariation of mean outside diameter of shaft Vdspvariation of outside diameter of shaft in a single plane dsdeviation of a single outside diameter of shaft Lsdeviation of the actu

38、al length of shaft 9 DIN ISO 13012-2:2010-02 5 Housings 5.1 General To facilitate the design and assembly of sleeve type linear ball bearings, specifically designed housings are available. Included in this part of ISO 13012 are the boundary dimensions and other related dimensions of sleeve type line

39、ar ball bearings series 5 as specified in ISO 10285:2007. The housings specified in Tables 1 and 2, and the corresponding sleeve type linear ball bearings should be supplied by the same producer. The reason for this is that the fixation of the bearings in the housings is specified by the producer an

40、d is not covered by this part of ISO 13012. 5.2 Housings for series 5 sleeve type linear ball bearings This part of ISO 13012 includes the following housing designs for series 5 linear ball bearings: closed and adjustable flangeless housings for series 5 sleeve type linear ball bearings (Table 1); o

41、pen and open adjustable flangeless housings for series 5 sleeve type linear ball bearings (Table 2). 6 Shaft support rails This part of ISO 13012 includes the following shaft support rails for sleeve type linear ball bearings: standard height shaft support rails for series 5 sleeve type linear ball

42、bearings (Table 3). 7 Shaft support blocks This part of ISO 13012 includes the following shaft support blocks for sleeve type linear ball bearings: flanged shaft support bl ocks for series 5 sleeve type linear ball bearings (Table 4). 8 Shafts 8.1 Material Shafts covered by this part of ISO 13012 ar

43、e precision hardened and ground steel shafts in both solid and tubular section. They are manufactured from high quality carbon steel or high quality carbon chrome steel and are either surface hardened or through hardened. 8.2 Heat treatment 8.2.1 Surface hardened shafts The cylindrical surface of th

44、e shafts is heat treated to provide a basically uniform effective depth of hardening and a surface hardness of not less than 653 HV (58 HRC) over the entire operating length. The effective depth of hardening shall be determined in accordance with ISO 3754. This effective depth of hardening is the di

45、stance from the outside surface of the shaft to a material layer at which the hardness is approximately 80 % of the specified minimum surface hardness. End faces of shafts may remain unhardened. 10 DIN ISO 13012-2:2010-02 8.2.2 Through hardened shafts The shafts shall be heat treated to give a surfa

46、ce hardness of no less than 653 HV (58 HRC) over the entire operating length. 8.3 Geometrical tolerances 8.3.1 Tolerance class The precision hardened and ground solid and tubular shafts are specified in one diameter tolerance class to match the sleeve type linear ball bearing and housing series 5. 8

47、.3.2 Geometric form The geometric form of the tolerance class is controlled by the following features: a) circularity (roundness): variation of shaft outside diameter in a single plane; b) cylindricity (taper, concavity, convexity): variation of mean shaft outside diameter; c) straightness (per metr

48、e). These tolerances for the class are shown in Table 5. A method for measuring straightness is illustrated in Figure 5 and defined in Table 5. 8.3.3 Shaft length tolerances These tolerances are given in Table 6. 8.3.4 Chamfers The shaft ends are provided with chamfers to facilitate entry of the sha

49、ft into the sleeve type linear ball bearing. The ends of shafts with machined end faces are usually provided with chamfers that are shallow in the radial direction and long in the axial direction. The length of the chamfer is shown in Table 5. Shafts for use with sealed sleeve type linear ball bearings shall have a chamfer angle less than 30. 8.3.5 Surface roughness The roughness of the cylindrical surface of the steel shaft is given in Table 5 in accordance with ISO 1302. 9 Bou