DIN ISO 16030-2007 Pneumatic fluid power - Connections - Ports and stud ends (ISO 16030 2001 + Amd 1 2005)English version of DIN ISO 16030-2007-05《气压传动 接头 端口和柱头螺栓端头 (ISO 16030-2001.pdf

1、May 2007DEUTSCHE NORM English price group 9No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 23.100.40!,x:t“9852381www.d

2、in.deDDIN ISO 16030Pneumatic fluid power Connections Ports and stud ends (ISO 16030:2001 + Amd. 1:2005)English version of DIN ISO 16030:2007-05Fluidtechnik Pneumatik-Leitungsanschlsse Einschraubloch und Einschraubzapfen (ISO 16030:2001 + Amd. 1:2005)Englische Fassung DIN ISO 16030:2007-05www.beuth.d

3、eDocument comprises 17 pages 08.07DIN ISO 16030:2007-05 2 Contents Page National foreword 3 National Annex NA (informative) Bibliography . 3 Introduction 4 1 Scope . 5 2 Normative references . 5 3 Terms and definitions 5 4 Dimensional requirements . 6 5 Performance requirements 6 5.1 Rated pressure

4、range . 6 5.2 Rated temperature range . 6 5.3 Performance verification 6 5.4 Sealing devices . 6 6 Test methods . 6 6.1 General . 6 6.2 Burst pressure test . 7 6.3 Leakage test 7 6.4 Cyclic endurance (impulse) test 8 6.5 Overtorque capability test . 8 6.6 Long-term creep test 9 7 Designation . 9 8 I

5、dentification statement (reference to this International Standard) 10 Annex A (informative) Examples of sealing methods . 14 Annex B (informative) Distances between centrelines of ISO 16030 ports 15 Bibliography 17 Figures Figure 1 Port . 11 Figure 2 Stud end . 12 Figure 3 Pressure impulse cycle wav

6、eform for cyclic endurance (impulse) test . 13 Figure A.1 Examples of sealing methods (see detail X in Figure 2) . 14 Figure B.1 Illustration of widths across corners of nuts or stud end bodies and diameters of connector collars 15 Tables Table 1 Port dimensions 11 Table 2 Stud end dimensions . 12 T

7、able 3 Torques for stud end qualification tests 13 Table B.1 Typical distances between centrelines of ISO 16030 ports and related information 16 DIN ISO 16030:2007-05 3 National foreword This standard has been prepared by Technical Committee ISO/TC 131 “Fluid power systems”. The responsible German b

8、ody involved in its preparation was the Normenausschuss Maschinenbau (Mechanical Engineering Standards Committee), Technical Committee NAM 236-21 Pneumatik. Amendment 1:2005 to ISO 16030 has been integrated in this standard. This standard has been prepared to give consideration to the miniaturisatio

9、n of pneumatic systems. For this reason, it covers metric threads of sizes M3, M5 and M7 for use in connections with thread sizes smaller than G 1/8. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsibl

10、e for identifying any or all such patent rights. The International Standards referred to in this standard have been published as the corresponding DIN ISO or DIN EN ISO Standards, except for those below, which correspond as follows: ISO 7-1 no national standard available ISO 7-2 no national standard

11、 available ISO 1179 no national standard available ISO 3448 similar to DIN 51519 ISO 4414 no national standard available ISO 8778 no national standard available ISO 14743 no national standard available The European Standard referred to in the bibliography has been published as the corresponding DIN

12、EN Standard. National Annex NA (informative) Bibliography DIN 51519, ISO viscosity classification of industrial liquid lubricants DIN ISO 16030:2007-05 4 Pneumatic fluid power Connections Ports and stud ends Introduction In pneumatic fluid power systems, power is transmitted and controlled through a

13、ir under pressure within a circuit. Components are connected through their threaded ports by means of connectors to tubes and pipes or to hose fittings and hoses. Ports are an integral part of fluid power components, such as valves, cylinders and filters. In the past, various thread and port systems

14、 (for example ISO 7-1 and ISO 1179:1981) have been used in pneumatic fluid power systems. See the scope of this International Standard for further information on the relationship between those standards and this International Standard. Where ISO 7-1 tapered external threads are intended to connect t

15、o pneumatic components with internal threads, the ports in those components should conform to ISO 1179:1981. DIN ISO 16030:2007-05 51 Scope This International Standard specifies dimensions and performance requirements for ports and stud ends with parallel threads for pneumatic fluid power applicatio

16、ns. It specifies reusable, positively retained seals for leak-free connections, for use at pressures from 0,09 MPa ( 0,9 bar 1) up to 1,6 MPa (16 bar). Only this International Standard is applicable for threaded ports and stud ends specified in new designs in pneumatic fluid power applications. Port

17、s and stud ends conforming to this International Standard are not intended to connect with ports and stud ends that conform to ISO 1179 or threads that conform to ISO 7-1. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute pr

18、ovisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of

19、the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads Par

20、t 1: Dimensions, tolerances and designation ISO 261, ISO general-purpose metric screw threads General plan ISO 3448, Industrial liquid lubricants ISO viscosity classification ISO 5598, Fluid power systems and components Vocabulary ISO 8778, Pneumatic fluid power Standard reference atmosphere 3 Terms

21、 and definitions For the purposes of this International Standard, the terms and definitions given in ISO 5598 apply. 1) 1 bar = 0,1 MPa = 105Pa; 1 MPa = 1 N/mm2DIN ISO 16030:2007-05 6 4 Dimensional requirements 4.1 Ports shall conform to the dimensions shown in Figure 1 and given in Table 1. 4.2 Stu

22、d ends shall conform to the dimensions shown in Figure 2 and given in Table 2. The sealing device is an integral part of the stud end. Examples of sealing types are shown in annex A. 5 Performance requirements 5.1 Rated pressure range Ports, stud ends and sealing devices shall be designed for use wi

23、thin a rated pressure range from 0,09 MPa ( 0,9 bar) up to 1,6 MPa (16 bar), unless otherwise specified by the manufacturer because of the requirements of the materials from which the ports, stud ends and sealing devices are made. It is important to ensure that there is sufficient material around th

24、e port to maintain the pressure. 5.2 Rated temperature range Ports, stud ends and sealing devices shall be designed for use within a rated temperature range from 20 C to + 80 C, unless otherwise specified by the manufacturer because of the requirements of the materials from which the ports, stud end

25、s and sealing devices are made. 5.3 Performance verification Ports, stud ends and sealing devices shall meet or exceed all of the requirements specified in clause 6. 5.4 Sealing devices Sealing devices shall be positively retained, reusable and capable of providing long-term performance. 6 Test meth

26、ods 6.1 General 6.1.1 Basic principles The tests in clause 6 are type tests to qualify port and stud end design and materials. Type tests are usually conducted only once, but retesting is necessary if there are changes in the material from which the port and stud ends are made. Parts used for any of

27、 the specified tests shall not be tested further, used, or returned to stock. 6.1.2 Test fluid The test fluid for the burst pressure test shall be a liquid, and the test fluid for the cyclic endurance (impulse) test shall be either a neutral gas or a liquid. The test fluid for the leakage test and t

28、he long-term creep test shall be a neutral gas. 6.1.3 Temperature Unless otherwise specified, tests shall be conducted at room temperature (23 C 5 C). DIN ISO 16030:2007-05 76.1.4 Material 6.1.4.1 Testing of ports The ports to be tested shall be from actual products. Stud ends that are used to test

29、ports shall be made of low-carbon steel or stainless steel, with dimension L4at its minimum. 6.1.4.2 Testing of stud ends and sealing devices The stud ends and sealing devices to be tested shall be from actual products. Test blocks that contain the test ports shall be made from low-carbon steel or s

30、tainless steel. 6.1.5 Thread lubrication For testing only, threads and contact surfaces shall be lubricated with hydraulic oil that has a viscosity of VG 32 in accordance with ISO 3448 prior to the application of torque, in order to test correctly the maximum clamp loading. 6.2 Burst pressure test 6

31、.2.1 Principle Test three samples to confirm that ports, stud ends and sealing devices meet or exceed a ratio of 5:1 between the burst pressure and maximum rated pressure. 6.2.2 Material and torque requirements 6.2.2.1 Testing of stud ends Test stud ends from actual products in the test block ports

32、(as described in 6.1.4.2) at the torque value given in Table 3. 6.2.2.2 Testing of ports Test ports from actual products with test stud ends (as described in 6.1.4.1) at twice the torque value given in Table 3. 6.2.3 Procedure and pressure rise rate Apply torque. Increase the pressure at a constant

33、rate so as to reach the specified test pressure within a time period of 3 s to 15 s. Once the specified test pressure has been reached, hold this pressure level for a period of at least 2 min. 6.2.4 Pass/fail criteria No cracks, fractures or separation of the stud end from the port shall appear. 6.3

34、 Leakage test 6.3.1 Principle Test three stud end samples at minimum torque to confirm that they do not leak after the application of 1,5 times the maximum rated pressure for a period of 2 min. It is not necessary to submit ports to the leakage test. DIN ISO 16030:2007-05 8 6.3.2 Material and torque

35、 requirements Test stud ends from actual products in the test block ports (as described in 6.1.4.2) at the minimum torque values specified by the connector manufacturer. 6.3.3 Procedure Apply a pressure equal to 1,5 times the maximum rated pressure for a period of 2 min. 6.3.4 Pass/fail criteria Lea

36、kage shall not occur during the application of pressure. 6.4 Cyclic endurance (impulse) test 6.4.1 Principle Test 10 samples to confirm that they do not exceed the allowed amount of leakage after the application of the specified maximum rated pressure within a tolerance of 20 %0+for a minimum of 1 0

37、00 000 cycles. 6.4.2 Material and torque requirements Test samples shall be as specified in 6.1.4 and shall consist of 10 samples of actual ports with test stud ends (as described in 6.1.4.1) and 10 samples of actual stud ends in the test block ports (as described in 6.1.4.2). Stud ends shall be tes

38、ted at the torque value given in Table 3 and ports at twice the torque value given in Table 3. 6.4.3 Procedure and pressure impulse cycle Submit each sample first to a pressure impulse cycle that meets the wave pattern shown in Figure 3 for 1 000 000 cycles and then to a leakage test (see 6.3). 6.4.

39、4 Pass/fail criteria After testing, each sample shall pass the leakage test, and the leakage rate of each sample shall not exceed 1 cm3/min (ANR) (see ISO 8778) at the maximum rated pressure when tested with a neutral gas. 6.5 Overtorque capability test 6.5.1 Principle Test three samples each of the

40、 port and the stud end to confirm that no severe deformation occurs because of the application of torque. 6.5.2 Material and torque requirements 6.5.2.1 Stud ends Test stud ends from actual products in the test block ports (as described in 6.1.4.2) at the torque value given in Table 3. 6.5.2.2 Ports

41、 Test ports from actual products with test stud ends (as described in 6.1.4.1) after application of twice the torque value given in Table 3. DIN ISO 16030:2007-05 96.5.3 Procedure Apply torque. The port test block or the actual tested product shall be restrained during the test, and the wrench shall

42、 be located at the hex of the stud end or the hex of the connector. 6.5.4 Pass/fail criteria Any visible crack or severe deformation that would render the port or stud end unusable shall be considered a failure. 6.6 Long-term creep test 6.6.1 Principle Test six samples of stud ends from an actual pr

43、oduct in the test block ports (as described in 6.1.4.2) to confirm that they do not exceed the allowed amount of leakage after the torque is applied and stud ends are subjected to the maximum rated pressure and the maximum rated temperature for a given time. It is not necessary to subject ports that

44、 are made from metal to this test. 6.6.2 Material and torque requirements For testing of ports and/or stud ends for long-term creep, the materials and test torques specified in 6.5.2 shall be used. 6.6.3 Procedure Apply torque. The assemblies shall then be held (aged) at the maximum rated pressure a

45、nd maximum rated temperature of the product for 1 000 h. 6.6.4 Pass/fail criteria After the test, the leakage rate shall not exceed 1 cm3/min (ANR) when the stud end is pressurized to 1,5 times the rated pressure at room temperature (23 C 5 C). 7 Designation Ports and stud ends conforming to this In

46、ternational Standard shall be designated by a) the word(s) “Port” or “Stud end”; b) reference to this International Standard (ISO 16030); c) thread size (dimension d1from Table 1 or 2); d) any adjustment to the temperature range specified in 5.2, in parentheses (if applicable). EXAMPLES Port ISO 160

47、30 - M7 Stud end ISO 16030 - G 1/8 Stud end ISO 16030 - G 1 ( 40 C/+ 50 C) DIN ISO 16030:2007-05 10 8 Identification statement (reference to this International Standard) Use the following statement in test reports, catalogues and sales literature when electing to comply with this International Stand

48、ard: ”Ports and/or stud ends conform to ISO 16030:2001, Pneumatic fluid power Connections Ports and stud ends.” DIN ISO 16030:2007-05 11Dimensions in millimetres Surface roughness in micrometres aThread bPitch diameter cNo burrs or radial scratches are allowed on this surface. dThis value applies wh

49、en the surface shows concentric grooves, otherwise Ra 2,4 m. Figure 1 Port Table 1 Port dimensions Dimensions in millimetres d2d3L1L2Threada(d1) min. nom. tol. max. min. M3 7 3,1 0,5 3,5 M5 9 5,1 0,5 4,5 M7 12 7,1 0,30+0,5 6 G 1/8 15 9,8 0,5 6 G 1/4 19 13,3 1 7 G 3/8 23 16,8 1 8 G 1/2 27 21 1 9,5 G 3/4 33 26,5 1 11 G 1 40 33,4 0,40+1 12 G 1 1/4 50 42,1 2 17 G 1 1/2 56 48 2 18 G 2 69 60 0,50+2 20 aMetric threads M3 to M7 shall conform to ISO 261 and pipe threads G 1/8 to G 2 shall conform to ISO 228-1. D