DIN ISO 1711-1-2007 Assembly tools for screws and nuts - Technical specifications - Part 1 Hand-operated wrenches and sockets (ISO 1711-1 2007) English version of DIN ISO 1711-1-20.pdf

1、May 2007DEUTSCHE NORM English price group 8No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 25.140.30!,x7J“9852039www.d

2、in.deDDIN ISO 1711-1Assembly tools for screws and nuts Technical specifications Part 1: Hand-operated wrenches and sockets (ISO 1711-1:2007)English version of DIN ISO 1711-1:2007-05Schraubwerkzeuge Technische Lieferbedingungen Teil 1: Handbettigte Schraubenschlssel und Steckschlsseleinstze (ISO 1711

3、-1:2007)Englische Fassung DIN ISO 1711-1:2007-05SupersedesDIN 899:2001-10www.beuth.deDocument comprises 9 pages 08.07DIN ISO 1711-1:2007-05 2 Contents Page National foreword 2 National Annex NA (informative) Bibliography . 3 1 Scope . 4 2 Normative references . 4 3 Test torsion torques . 5 4 Hardnes

4、s testing . 5 5 Torque testing . 6 5.1 General . 6 5.2 Method . 6 5.3 Test of box wrenches or open jaw wrenches 7 5.4 Test of socket wrenches 7 5.5 Test of hand-operated square drive sockets . 7 Bibliography . 9 National foreword This standard has been prepared by Technical Committee ISO/TC 29 “Smal

5、l tools”, Subcommittee SC 10 “Assembly tools for screws and nuts, pliers and nippers”. The responsible German body involved in its preparation was the Normenausschuss Werkzeuge und Spannzeuge (Tools and Clamping Devices Standards Committee), Technical Committee NA 121-08-01 AA Schraubwerkzeuge. Beca

6、use International Standard ISO 1711-1 “Assembly tools for screws and nuts Technical specifica-tions Part 1: Hand-operated wrenches and sockets” has been revised by ISO/TC 29/SC 10, Technical Committee NA 121-08-01 AA decided to adopt the standard as a DIN ISO Standard. Attention is drawn to the poss

7、ibility that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. ISO 1711 consists of the following parts, under the general title Assembly tools for screws and nuts Tech-nical specifications: Par

8、t 1: Hand-operated wrenches and sockets Part 2: Machine-operated sockets (“impact”) The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 272 DIN ISO 272 ISO 6508-1 DIN EN ISO 6508-1 ISO 6508-2 DIN EN ISO 6508-2 ISO 6508-3 DIN EN ISO 6508-3 D

9、IN ISO 1711-1:2007-05 3 Amendments This standard differs from DIN 899:2001-10 as follows: a) ISO 1711-1:2007 has been adopted in its entirety. Test torsion torques of series B and D and specifications for surface finish, protective coating and marking are no longer included. b) The standard only cov

10、ers widths across flats to DIN ISO 272. Widths across flats 3, 3,5, 4,5, 9, 12, 14, 17, 19, 20, 22, 23, 25, 26, 28, 32, 35, 80, 85, 90 and 95 have been dropped. These sizes and test torsion torques of series B and D, including the test values, are contained in the relevant product standards. Previou

11、s editions DIN 899: 1957-04, 1964-11, 1968-01, 1972-08, 1976-04, 1980-01, 2001-10 National Annex NA (informative) Bibliography DIN EN ISO 6508-1, Metallic materials Rockwell hardness test Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) DIN EN ISO 6508-2, Metallic materials Rockwell hard

12、ness test Part 2: Verification and calibration of testing machines (scales A, B, C, D, E, F, G, H, K, N, T) DIN EN ISO 6508-3, Metallic materials Rockwell hardness test Part 3: Calibration of reference blocks (scales A, B, C, D, E, F, G, H, K, N, T) DIN ISO 272, Fasteners Width across flats for hexa

13、gon products DIN ISO 1711-1:2007-05 4 Assembly tools for screws and nuts Technical specifications Part 1: Hand-operated wrenches and sockets 1 Scope This part of ISO 1711 specifies minimum values for Rockwell hardness and torsional strength for hand-operated wrenches and sockets. It covers the follo

14、wing three series of torsion torques. Series A: usual box wrenches and socket wrenches EXAMPLE Reference nos. 1 1 02 01 0; 1 1 02 02 0 and 1 1 02 02 1; 1 1 02 03 0; 1 1 02 04 0; 1 1 02 05 0; 1 1 02 06 0; 1 1 02 09 0; 1 1 02 10 0; 1 1 02 11 0; 1 1 02 12 0; 1 1 02 13 0 and 1 1 02 13 1; 1 1 02 14 0; 1

15、1 02 15 0; 1 1 08 01 0; 1 1 08 02 0. Series C: open end wrenches EXAMPLE Reference nos. 1 1 01 01 0; 1 1 01 01 1; 1 1 01 02 0; 1 1 01 03 0; 1 1 01 04 0. Series E: hand-operated square drive sockets EXAMPLE Reference nos. 2 1 02 01 0 and 2 1 02 01 1. NOTE The wrenches and sockets mentioned above are

16、listed under their respective reference numbers in ISO 1703. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (

17、including any amendments) applies. ISO 6508 (all parts), Metallic materials Rockwell hardness test DIN ISO 1711-1:2007-05 53 Test torsion torques The empiric formulae giving minimum test torsion torques, M, in newton metres, as a function of width across flats, s, in millimetres, are given for infor

18、mation in Table 1. The minimum test torsion torques to be applied are given in Table 3. Table 1 Formulae giving minimum test torsion torques Series Minimum test torsion torque M N m A 0,265 7 s2,34 36 0,039 2 s2,8C Width across flats, s mm 36 0,686 5 s26,3 0,980 7 s1,710 0,350 s2,34a12,5 1,471 s220

19、2,451 7 s1,7E Nominal dimension for driving square mm 25 46,581 6 s aTest torque M applicable to Series A multiplied by the coefficient 1,32. 4 Hardness testing The hardness test shall be carried out in accordance with ISO 6508. Minimum Rockwell hardness values are given in Table 2. Table 2 Minimum

20、Rockwell hardness values for wrenches and sockets Minimum hardness Width across flats s mm Alloy steel open end and double head wrenches aAll other wrenches or sockets s 34 42 HRC 39 HRC 34 s 70 39 HRC 35 HRC aFor carbon steel open end wrenches, the hardness value shall be 36 HRC. DIN ISO 1711-1:200

21、7-05 6 5 Torque testing 5.1 General For combined wrenches (for example, reference nos. 1 1 01 05 0 and 1 1 01 06 0), the box wrench side shall be tested in accordance with Table 3, Series A, and the open end wrench side shall to be tested in accordance with Table 3, Series C. 5.2 Method The wrench o

22、r the socket shall be fully engaged in a hexagon test mandrel as shown in Figure 1. The height, h, and the width across corners, emin., of the mandrel are specified in Table 3. Smoothly apply the load until the minimum testing torque as given in Table 3 is reached. The nominal across-flats dimension

23、 of the test mandrel shall be equal to the nominal dimension, s, with a tolerance of h8. The mandrel shall be hardened to not less than hardness 55 HRC. A device in which the mandrel can be rotated at a certain torque determined with an accuracy of 2,5 % may also be used for this test. Following the

24、 application of the minimum test torsion torque, any possible damage or deformation shall not affect usability of tool. Figure 1 Test mandrel height, width across flats and width across corners DIN ISO 1711-1:2007-05 75.3 Test of box wrenches or open jaw wrenches Apply the load as far along the shaf

25、t of the wrench as possible, perpendicular to its longitudinal axis. Use an extension tube when testing large wrenches. Load the wrench once in each direction during the test. For open jaw wrenches, the head shall remain perpendicular to the mandrel axis during the test. For box wrenches, the axis o

26、f the head shall remain perpendicular to the mandrel axis during the test. 5.4 Test of socket wrenches Apply the load as far along the shaft of the wrench as possible, perpendicular to its longitudinal axis. Use an appropriate test device that will safely test large wrenches. The axis of the socket

27、wrenches and the axis of the mandrel shall remain coaxial during the test. 5.5 Test of hand-operated square drive sockets A square mandrel of hardness not less than 55 HRC shall be used for driving the socket. The nominal across-flats dimension of this mandrel shall be equal to the maximum dimension

28、, with a tolerance of h8, of the corresponding driving square. The axes of the two mandrels and the axis of the socket shall remain coaxial during the test. DIN ISO 1711-1:2007-05 8 Table 3 Minimum test torsion torques and test mandrel height as function of width across flats Minimum test torsion to

29、rque, M N m Test mandrel Series E Nominal width across flats as Driving square nominal dimension bHeight h h13 Width across corners eemin.mm A C mm mm mm 6,3 10 12,5 20 25 3,2 4,04 1,02 7,08 1,3 3,62 4 6,81 1,9 10,4 1,6 4,52 5 11,5 3,55 15,1 2 5,65 5,5 14,4 4,64 17,8 2,4 6,22 7 25,2 9,12 26,8 33,2 3

30、,2 7,91 8 34,5 13,3 33,6 45,5 94 4 9,04 10 58,1 24,8 49,1 76,7 147 4,8 11,30 11 72,7 32,3 57,8 96 178 5,6 12,43 13 107 51,6 68,6 c141 249 6,4 14,69 15 150 77 68,6 c198 331 7,4 16,95 16 175 92,3 68,6 c225 c377 8 18,08 18 230 128 225 c477 9,6 20,34 21 330 198 225 c569 569 d 11,2 23,73 24 451 287 225 c

31、569 c569 d 12,8 27,12 27 594 399 569c665 14,4 30,51 30 760 536 569c795 16 33,90 34 1 019 761 569c984 17,6 38,42 36 1 165 894 1 084 19,2 40,68 41 1 579 1 154 1 353 1 910 21,6 46,33 46 2 067 1 453 1 569 c2 143 24 51,98 50 2 512 1 716 1 569 c2 329 26,4 56,50 55 3 140 2 077 1 569 c2 562 28,8 62,15 60 3

32、849 2 471 1 569 c2 795 c31,2 67,80 65 4 021 2 900 2 795 c33,5 73,45 70 4 658 3 364 2 795 c36 79,10 aAccording to ISO 272. bFor dimensions of driving squares, see ISO 1174-1. cValue of test torque voluntarily limited. Driving squares have lower strengths than sockets of the same steel grade. dValue g

33、reater than that which might have been obtained by computation, nevertheless adopted as it would be abnormal for the strength of sockets with driving squares of 20 mm to be lower than the strength of sockets with driving squares of 12,5 mm. eemin.= snom 1,13. DIN ISO 1711-1:2007-05 9Bibliography 1 ISO 272, Fasteners Hexagon products Widths across flats 2 ISO 1174-1, Assembly tools for screws and nuts Driving squares Part 1: Driving squares for hand socket tools 3 ISO 1703, Assembly tools for screws and nuts Designation and nomenclature