DIN ISO 3547-6-2015 Plain bearings - Wrapped bushes - Part 6 Checking the inside diameter (ISO 3547-6 2007)《滑动轴承 卷制轴衬 第6部分 内径检验(ISO 3547-6-2007)》.pdf

1、December 2015 English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 21.100.10!%Jx“2399685www.din.deD

2、IN ISO 3547-6Plain bearings Wrapped bushes Part 6: Checking the inside diameter (ISO 3547-6:2007),English translation of DIN ISO 3547-6:2015-12Gleitlager Gerollte Buchsen Teil 6: Prfung des Innendurchmessers (ISO 3547-6:2007),Englische bersetzung von DIN ISO 3547-6:2015-12Paliers lisses Bagues roule

3、s Partie 6: Contrle du diamtre intrieur (ISO 3547-6:2007),Traduction anglaise de DIN ISO 3547-6:2015-12SupersedesDIN ISO 12307-2:2001-09, withdrawn 2011-06www.beuth.deDocument comprises 11 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered auth

4、oritative.01.16A comma is used as the decimal marker. Contents Page National foreword .3 National Annex NA (informative) Bibliography 4 1 Scope 5 2 Normative references 5 3 Symbols and units .6 4 Method of checking .6 5 Test equipment 6 5.1 Ring gauge .6 5.2 Plug gauge 8 5.3 Three-point measuring in

5、strument 9 5.4 Requirements for measuring equipment . 10 5.5 Measuring errors. 10 6 Procedure 10 Bibliography . 11 DIN ISO 3547-6:2015-12 2National foreword This document (ISO 3547-6:2007) has been prepared by Technical Committee ISO/TC 123 “Plain bearings” (Secretariat: JISC, Japan), Subcommittee S

6、C 5 “Quality analysis and assurance”. The responsible German body involved in its preparation was DIN-Normenausschuss Wlz- und Gleitlager (DIN Standards Committee Rolling Bearings and Plain Bearings), Working Committee NA 118-02-05 AA Qualittssicherung. Attention is drawn to the possibility that som

7、e of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 3547-1 DIN ISO 3547-1 ISO 3547-2 DI

8、N ISO 3547-2 ISO 3547-5 DIN ISO 3547-5 ISO 3547-7 DIN ISO 3547-7 ISO 12301 DIN ISO 12301 DIN ISO 3547 consists of the following parts, under the general title Plain bearings Wrapped bushes: Part 1: Dimensions Part 2: Test data for external and internal diameters Part 3: Lubrication holes, grooves an

9、d indentations Part 4: Materials Part 5: Checking the outside diameter Part 6: Checking the inside diameter Part 7: Measurement of wall thickness of thin-walled bushes Amendments This standard differs from DIN ISO 12307-2:2001-09 as follows: a) the standard has been technically and editorially revis

10、ed. Previous editions DIN 31672: 1983-11 DIN ISO 12307-2: 2001-09 DIN ISO 3547-6:2015-12 3National Annex NA (informative) Bibliography DIN ISO 3547-1, Plain bearings Wrapped bushes Part 1: Dimensions DIN ISO 3547-2, Plain bearings Wrapped bushes Part 2: Test data for external and internal diameters

11、DIN ISO 3547-5, Plain bearings Wrapped bushes Part 5: Checking the outside diameter DIN ISO 3547-7, Plain bearings Wrapped bushes Part 7: Measurement of wall thickness of thin-walled bushes DIN ISO 12301, Plain bearings Quality control techniques and inspection of geometrical and material quality ch

12、aracteristics DIN ISO 3547-6:2015-12 41 Scope The part of ISO 3547 specifies, following ISO 12301, the checking of the inside diameter of wrapped bushes (see ISO 3547-2:2006, method C) and describes the necessary checking methods and measuring equipment. Wrapped bushes in the free condition are flex

13、ible, but after insertion they adapt largely to the shape of the housing bore due to the interference between the outside diameter of the bush and the housing bore. NOTE 1 All dimensions in this part of ISO 3547 are given in millimetres except where otherwise noted/designated. NOTE 2 The dimensions

14、and tolerances of wrapped bushes are given in ISO 3547-1. NOTE 3 Checking of the wall thickness is the subject of ISO 3547-7. NOTE 4 Checking of the outside diameter of wrapped bushes is the subject of ISO 3547-5. 2 Normative references The following referenced documents are indispensable for the ap

15、plication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3547-1:2006, Plain bearings Wrapped bushes Part 1: Dimensions Plain bearings Wrapped bushes Part 6: Checking

16、 the inside diameter DIN ISO 3547-6:2015-12 53 Symbols and units See Table 1. Table 1 Symbols and units Symbol Parameter Unit B Nominal width of the bush millimetres bch, 1Width of the ring gauge millimetres bch, 2Width of the plug gauge millimetres d0Outside diameter of the ring gauge millimetres D

17、iNominal inside diameter of the bush millimetres Di, chInside diameter of the bush in the ring gauge millimetres DoNominal outside diameter of the bush millimetres RaSurface roughness micrometres t1Tolerance of form and position millimetres dch, 1Inside diameter of the ring gauge millimetres dch, 2O

18、utside diameter of the plug gauge millimetres 4 Method of checking The free diameter of a wrapped bush is not measured directly because of the flexible nature of the components. To check the inside diameter, Di, ch, the bush is pressed into a ring gauge whose nominal diameter corresponds to the dime

19、nsion of the housing. For bushes specified in ISO 3547-1, the tolerance class of housing bore is normally H7. When the bush is pressed into the ring gauge, it is possible that there is a permanent reduction in the outside diameter. The inside diameter, Di, ch, is measured with a three-point measurin

20、g instrument or with a GO or a NO GO gauge. In order to enable the supplier and the user to compare results of this test it shall be agreed whether results shall be obtained by measuring or by gauging. 5 Test equipment 5.1 Ring gauge Unless otherwise agreed between supplier and user, the dimensions

21、shown in Figure 1 and given in Table 2 are valid for the ring gauge. DIN ISO 3547-6:2015-12 6Dimensions in millimetres, unless otherwise designated abch, 1W B + 9 bdoW dch, 1+ 50 Figure 1 Ring gauge Table 2 Dimensions, manufacturing tolerances and wear limits for ring gauges and plug gauges Dimensio

22、ns in millimetres Doanominal dch, 1dch, 2t1Target SizebManufacturing tolerance Wear limit Manufacturing tolerance Wear limit Manufacturing tolerance Wear limit u 10 Do+ 0,008 10 u 18 Do+ 0,009 18 u 30 Do+ 0,011 30 u 50 Do+ 0,013 50 u 80 Do+ 0,015 80 u 120 Do+ 0,018 0,0030+0,0050+00,0030,005 0,002 0,

23、004 120 u 180 Do+ 0,020 0,0050+0,007 00,0050,007 0,003 0,005 aFor bushes with Do 180 mm, agreement shall be reached between the supplier and user. bThe target size of the ring gauge inside diameter is made up of Doand the rounded average value of the tolerance class H7. In ISO 3547-1, H7 is recommen

24、ded as the tolerance class for the housing bore. DIN ISO 3547-6:2015-12 75.2 Plug gauge Unless otherwise agreed between supplier and user, the following dimensions are valid for the plug gauge (see Figures 2 and 3 and Table 2). The nominal plug gauge diameter can be obtained from Table 4 in ISO 3547

25、-1:2006. Key 1 field for marking abch, 2W B + 5 Figure 2 Plug gauge, solid, for dch, 2u 80 mm DIN ISO 3547-6:2015-12 8Dimensions in millimetres, unless otherwise designated Key 1 field for marking abch, 2W B + 5 Figure 3 Plug gauge, example with blind hole, for dch, 2 80 mm 5.3 Three-point measuring

26、 instrument Measures are made in the radial direction using the spherical faces of the measuring pins shown in Figure 4. Figure 4 Three-point measuring instrument DIN ISO 3547-6:2015-12 95.4 Requirements for measuring equipment The ring gauge and plug gauge shall be from hardened (60 HRC to 64 HRC)

27、and non-ageing steel. 5.5 Measuring errors Frequent measuring errors are as follows. a) Ring gauge and plug gauge are damaged or worn. b) Ring gauge and plug gauge have no lead-in chamfer. c) Bush is misaligned when introduced into the ring gauge. d) Plug gauge is misaligned when introduced into the

28、 bush. e) Width of the ring gauge is less than the width of the bush. f) Grease, dirt, damages, burrs and swelling are present around features on the bush and test equipment. 6 Procedure The bush shall be introduced into the ring gauge from that side having the lead-in chamfer. Subsequently, the ins

29、ide diameter shall be determined by means of a) the three-point measuring instrument; b) the GO plug gauge (see Figures 2 and 3), which shall be inserted with minimum effort; the NO-GO plug gauge, which shall not be able to be inserted manually with a maximum force of 250 N. Where it is necessary to

30、 limit the maximum force, it shall be agreed between supplier and user. DIN ISO 3547-6:2015-12 10Bibliography 1 ISO 3547-2:2006, Plain bearings Wrapped bushes Part 2: Test data for outside and inside diameters 2 ISO 3547-5, Plain bearings Wrapped bushes Part 5: Checking the outside diameter 3 ISO 3547-7, Plain bearings Wrapped bushes Part 7: Measurement of wall thickness of thin-walled bushes 4 ISO 12301, Plain bearings Quality control techniques and inspection of geometrical and material quality characteristics DIN ISO 3547-6:2015-12 11