DIN ISO 5610-14-2015 Tool holders with rectangular shank for indexable inserts - Part 14 Style H (ISO 5610-14 2014)《可转位刀片用方柄刀杆 第14部分 H型(ISO 5610-14-2014)》.pdf

1、February 2015 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 25.100.01; 25.060.20!%?cU“2286450www.din.deDDIN ISO 5610-14Tool holders with rectangular shank for indexable inserts Part 14: Style H (ISO 5610-14:2014),English translation of DIN ISO 5610-14:2015-02Klemmhalter mit Vierkantschaft fr Wendeschneidplatten Teil 14: Form H (ISO 5610-14:2014),Englische

3、bersetzung von DIN ISO 5610-14:2015-02Porte-plaquette queue rectangulaire pour plaquettes amovibles Partie 14: Forme H (ISO 5610-14:2014),Traduction anglaise de DIN ISO 5610-14:2015-02SupersedesDIN 4984-14:2004-07www.beuth.deDocument comprises 12 pagesIn case of doubt, the German-language original s

4、hall be considered authoritative.01.15A comma is used as the decimal marker. Contents Page National foreword 3 National Annex NA (informative) Bibliography . 4 1 Scope . 5 2 Normative references 5 3 Dimensions 5 3.1 General 5 3.2 Tool holder style H for rhombic indexable insert shape D 6 3.3 Tool ho

5、lder style H for rhombic indexable insert shape V 8 4 Designation . 9 5 Material . 10 6 Design . 10 6.1 Type of mounting 10 6.2 Corner radius, r10 6.3 Thickness, s, of indexable insert . 10 7 Extent of delivery . 11 8 Marking 11 Bibliography . 12 2DIN ISO 5610-14:2015-02 National foreword This docum

6、ent (EN ISO 5610-14:2014) has been prepared by Technical Committee ISO/TC 29 “Small tools”, Subcommittee SC 9 “Tools with defined cutting edges, cutting items” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the DIN-Normenausschuss Werkzeuge und Spannzeuge (D

7、IN Standards Committee Tools and Clamping Devices), Working Committee NA 121-01-12 AA Dreh- und Bohrwerkzeuge mit Wendeschneidplatten aus harten Schneidstoffen. This is the first edition of the DIN ISO 5610 series, and replaces the DIN 4984 series, which was the basis for this series of Internationa

8、l Standards. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN and/or DKE shall not be held responsible for identifying any or all such patent rights. DIN ISO 5610 consists of the following parts, under the general title Tool ho

9、lders with rectangular shank for indexable inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part 8: Style K Part 9: Style L Part 10: Style N Part 11: Style R Part 12: Style S P

10、art 13: Style T Part 14: Style H Part 15: Style V The DIN Standard corresponding to the International Standard referred to in this document is as follows: ISO 6987 DIN ISO 6987 Amendments This standard differs from DIN 4984-14:2004-07 as follows: a) the text of the International Standard has been ad

11、opted without any modification. Previous editions DIN 4984-14: 1987-06, 2004-07 DIN ISO 5610-14:2015-02 3National Annex NA (informative) Bibliography DIN 4000-1, Tabular layouts of properties Part 1: Concepts and principles DIN 4000-76, Tabular layouts of properties Part 76: Inserts, indexable DIN 4

12、000-77, Tabular layouts of properties Part 77: Inserts, clamped, for grooving, parting and thread machining DIN 4000-90, Tabular layouts of properties Part 90: Tool holders for indexable inserts DIN 4967-1, Indexable hardmetal inserts with rounded corners, with partly cylindrical hole 7 normal clear

13、ance DIN 4967-2, Indexable hardmetal inserts with rounded corners, with partly cylindrical hole 11 normal clearance DIN 4968, Indexable hardmetal inserts with rounded corners, without fixation hole DIN 4969-1, Ceramic indexable inserts, with rounded corners, without fixing hole DIN 4983, Tool holder

14、s with rectangular shank and cartridges for indexable inserts Presentation of the designation DIN 4988, Indexable hardmetal inserts with rounded corners, with cylindrical fixation hole DIN 6580, Terminology of chip removing Movements and geometry of the chip removing process DIN 6581, Terminology of

15、 chip removing Reference systems and angles on the cutting part of the tool DIN 6582, Terminology of cutting Additional terms for the tool, wedge and the cutting edge DIN 6584, Terms of the cutting technique Forces, energy, work, power DIN ISO 6987, Indexable hard material inserts with rounded corne

16、rs, with partly cylindrical fixing hole Dimensions ISO/TS 13399-201, Cutting tool data representation and exchange Part 201: Creation and exchange of 3D models Regular inserts ISO/TS 13399-202, Cutting tool data representation and exchange Part 202: Creation and exchange of 3D models Irregular inser

17、ts DIN ISO 5610-14:2015-02 4Tool holders with rectangular shank for indexable inserts Part 14: Style H1 ScopeThis part of ISO 5610 specifies tool holders with rectangular shank, style H, i.e. with offset shank and cutting edge angle r= 107,5 for side cutting.These tool holders are primarily intended

18、 for indexable inserts made of hard metal or other cutting materials to be mounted by clamping and to be used for turning operations.NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred symbols of properties defined in ISO/TS 13399-2 and IS

19、O/TS 13399-3 are given in ISO 5610-1:2014, Table A.1.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edi

20、tion of the referenced document (including any amendments) applies.ISO 5608:2012, Turning and copying tool holders and cartridges for indexable inserts DesignationISO 5610-1:2014, Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determination of dimen

21、sions3 Dimensions3.1 GeneralIt is not necessary for tool holders to comply with the pictorial representation; only the dimensions given shall be observed.For determination of dimensions h1, f, and l1, see ISO 5610-1.For explanation of the designation code for tool holders, see ISO 5608.NOTE The valu

22、es of rake angles and inclination angles shown in the figures are recommended values; they can vary according to the application.DIN ISO 5610-14:2015-02 53.2 Tool holder style H for rhombic indexable insert shape DKeyaInclination angle, s.bRake angle, o.NOTE This figure shows a right-hand tool holde

23、r (R); left-hand tool holder (L) laterally reversed.Figure 1 Tool holder style H for rhombic indexable insert DDIN ISO 5610-14:2015-02 6Table 1Dimensions in millimetresSymbolah1js13bh13l3f005+ ,h2h13l1ak16l2max.sbSDHCR 1010 0710 10 7,75 12 10 25 2,38SDHCL 1010 07SDHCR 1212 0712 12 7,75 16 12 32 2,38

24、SDHCL 1212 07SDHCR 1616 1116 16 11,6 20 16 32 3,97SDHCL 1616 11SDHCR 2020 1120 2011,625 20 403,97SDHCL 2020 11PDHNR 2020 1515,5 6,35PDHNL 2020 15CDHNR 2525 1525 25 15,5 32 25 407,94CDHNL 2525 15SDHCR 2525 154,76SDHCL 2525 15PDHNR 2525 156,35PDHNL 2525 15CDHNR 3225 1532 25 15,5 32 32 407,94CDHNL 3225

25、 15SDHCR 3225 154,76SDHCL 3225 15PDHNR 3225 156,35PDHNL 3225 15aFor the selection of length l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.DIN ISO 561

26、0-14:2015-02 73.3 Tool holder style H for rhombic indexable insert shape VKeyaInclination angle, s.bRake angle, o.NOTE This figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.Figure 2 Tool holder style H for rhombic indexable insert VDIN ISO 5610-14:2015-02 8Tabl

27、e 2Dimensions in millimetresSymbolah1js13bh13l3f005+ ,h2h13l1ak16l2max.sbSVHBR 1212 1112 12 11,1 16 12 253,18SVHBL 1212 11SVHBR 1616 1116 16 11,1 20 16 25SVHBL 1616 11SVHBR 2020 1620 20 16,6 25 20 40 4,76SVHBL 2020 16SVHBR 2525 1625 25 16,6 32 25 40 4,76SVHBL 2525 16SVHBR 3225 1632 25 16,6 32 25 40

28、4,76SVHBL 3225 16aFor the selection of length l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.4 DesignationA tool holder in accordance with this part o

29、f ISO 5610 shall be designated by:a) “Tool holder”;b) a reference to this part of ISO 5610 (i.e. ISO 5610-14);c) type of mounting, in accordance with ISO 5608;d) symbol for indexable insert shape, in accordance with ISO 5608;e) symbol for tool style, in accordance with ISO 5608;f) symbol for the ind

30、exable insert normal clearance, in accordance with ISO 5608;g) symbol for hand of tool, in accordance with ISO 5608;h) its height h1, width b, and length l1(symbol for tool length in accordance with ISO 5608);i) its cutting edge length l3.EXAMPLE 1 Tool holder for a horizontally mounted, bore-clampe

31、d (P) rhombic indexable insert shape D (D), tool holder style H (H), for normal clearance of indexable insert n= 0 (N), right-hand type (R), with height h1= 32 mm and width b = 25 mm (3225), length l1= 170 mm (P), for cutting edge length l3= 15,5 mm (15) is designated as follows:Tool holder ISO 5610

32、-14 - PDHNR 3225 P15EXAMPLE 2 Tool holder for a screw-clamped (S) rhombic indexable insert shape V (V), tool holder style H (H), for normal clearance of indexable insert n= 5 (B), right-hand type (R), with height h1= 25 mm and width b = 25 mm (2525), length l1= 150 mm (M), for cutting edge length l3

33、= 16,6 mm (16) is designated as follows:Tool holder ISO 5610-14 - SVHBR 2525 M16DIN ISO 5610-14:2015-02 95 MaterialThe material should be steel with a tensile strength of at least 1 200 N/mm2.6 Design6.1 Type of mountingStandard design of tool holders with indexable insert shall be mounted in accord

34、ance with Tables 1 and 2.Other types of mounting are at the manufacturers discretion or upon agreement. The letter symbol in the designation, symbol 1, shall then be replaced by the respective symbol for the chosen or agreed-upon type of mounting in accordance with ISO 5608.For the modified type of

35、mounting deviating from Tables 1 and 2, the relevant indexable insert thickness shall also be considered.6.2 Corner radius, rTool holders in accordance with this part of ISO 5610 can be equipped with indexable inserts with cutting edge length, l3, as specified in Tables 1 and 2, and any corner radiu

36、s r.The values for l1given in ISO 5610-1:2014, Table 2, apply to tool holders with indexable inserts having corner radii, r, in accordance with Table 3.Table 3Dimensions in millimetresl3rD V7,75 0,4 11,111,6 0,815,5 16,6NOTE The values given for rare nominal values. The accurate values converted fro

37、m the inch dimensions are 0,397 mm and 0,794 mm.For indexable inserts with corner radii, r, other than those specified in Table 3, the dimensions f and l1shall be determined in accordance with ISO 5610-1.The tolerances for h1, f, and l1refer to dimensions measured with master indexable insert and ma

38、ster shim, if applicable.6.3 Thickness, s, of indexable insertThe values for thickness, s, given in Tables 1 and 2, apply to indexable inserts without shim and for the standard design of tool holders.For tool holders for indexable inserts with thicknesses deviating from the specified values, the thi

39、ckness shall be indicated when ordering or upon delivery (in the handbook).DIN ISO 5610-14:2015-02 107 Extent of deliveryTool holders shall be delivered complete with clamping device, but without indexable insert(s).8 MarkingTool holders shall be marked with the letter symbol and the name or tradema

40、rk of the manufacturer.Additional marking is at the manufacturers discretion or upon agreement.Deviations in marking may be by mutual agreement.A reference to this part of ISO 5610, i.e. ISO 5610-14:2014, shall be given on the packaging.DIN ISO 5610-14:2015-02 11Bibliography1 ISO 883, Indexable hard

41、metal (carbide) inserts with rounded corners, without fixing hole Dimensions2 ISO 3002-1, Basic quantities in cutting and grinding Part 1: Geometry of the active part of cutting tools General terms, reference systems, tool and working angles, chip breakers3 ISO 3364, Indexable hardmetal (carbide) in

42、serts with rounded corners, with cylindrical fixing hole Dimensions4 ISO 6987, Indexable hard material inserts with rounded corners, with partly cylindrical fixing hole Dimensions5 ISO/TS 13399-2, Cutting tool data representation and exchange Part 2: Reference dictionary for the cutting items6 ISO/TS 13399-3, Cutting tool data representation and exchange Part 3: Reference dictionary for tool itemsDIN ISO 5610-14:2015-02 12